Hot

Geezerhood · Aug 24, 2023

I am now on my 4th Notos - Two for me and two for family members. I noticed that on one of them the moderator will rotate fairly easily but only very slightly in both directions with a firm stop at each end of the travel. Maybe a total of about 3 degrees? What could be causing that?

I haven't shot it yet but it doesn't seem to be loose as far as bore alignment goes, just that strange circular movement.

All the others did not show any movement of the moderator. So far they all like CPHPs and H&N FTTs, outshooting several of my airguns that I paid a LOT more $$ for.

Shortcut · Aug 24, 2023

Sight in time

bsahogger · Aug 24, 2023

I need help in selecting a pcp rifle for HFT. I’ve collected air guns all my life & have always wanted to get into FT but couldn’t due to career pressure. This year I decided to take the plunge & I started researching guns. I’ve owned many Air Arms guns over the years (still have a TX200) so I naturally leaned that way. The HFT XTi50 looked good so I reached out to Pyramyd to see whether they would get them in but they just kept saying they didn’t know, eventually they recommended that I get a S510 XS Ultimate Sporter with a single shot tray from Rowan. Ordered the gun, ordered the tray (great product & service from Rowan), ordered a scope, ordered ammo. The gun came in & was broken: it shot a foot low at 20 yds, turret all the way up (tried two scopes). Contacted Pyramyd & got no reply for 4 days, eventually emailed AA in the UK & was immediately told that the breech was bad. They contacted Pyramyd on my behalf, long story short Pyramyd sent me what they termed a ‘new’ gun. That eventually came in after about 3 weeks with the to & from shipping, meaning I missed out on the event down in Ashland Oregon. New gun wouldn’t hold air for longer than a day. Again contacted Pyramyd, who again said they’d swap it for a new one. Again sent the gun back, didn’t hear anything for a week after they received it, reached out & was told that the guns are out of stock & hopefully they’d have one in over a month from now. Begged, pleaded, asked for a different gun, no help. SO, there’s another shoot in Ashland at the end of September, which I’d like to start practicing for & I’d like to get some advice on what to get since I’m now super leery of Air Arms (sadly) & Pyramyd. My requirements are the following:
More than 12ft/lbs , preferably around 16ft/lbs, that’s why I initially chose a S510 over the HFT500.
Not too long, I struggle with standing shots when the rifle is too long.
Adjustable cheek piece.
Adjustable butt pad.
Quick fill (this is why I don’t like any of the German/Austrian guns).
Single shot with large loading port.
Accessory rail for hamster.
No POI shifts, tried many many of the cheap guns over the years, never again.
Aluminum chassis & shroud style moderator would be nice as well.

ctshooter · Aug 24, 2023

Sales Rules:

I accept PayPal or Venmo - F&F only. Not my preference, but will also do check or USPS MO and ship once cleared.
CONUS shipping is included in the asking price.
I will go based on PM timestamp.
Please - no trade offers for this sale.

Up for sale is an extremely rare Brocock BACS Model 1851 Navy .22 pistol. This pistol is made of 100% pure unobtanium. You cannot find these pistols anywhere and this packages includes all the fill equipment you need. This is the most complete package you'll ever find.

The pistol is in good working condition. All cartridges have working seals, hold air and shoot with no issues.

Included in the sale are:

Brocock BACS Model 1851 Navy .22
Slim Jim hand pump
4 Brass BACS cartridges
6 Stainless Steel BACS cartridges
PCP fill adapter
O-ring replacement tool
6 smaller BACS cartridges and PCP fill adapter (for smaller style BACS pistols)

Price: $750 SHIPPED SOLD

CrashKT · Aug 24, 2023

I'm looking to get a HM1000X no mod. But since I like to tinker, I saw Huma makes a reg for it HERE. It says I don't need to run the V-shaped fill port and pressure gauge connector. If I use that, how would I fill it, just take the bottle off every time?

ShootingNewB · Aug 24, 2023

NOW in .177, .22 AND .25 CALIBER!!

These have been out and in the field now for over 2 years now and have been quite the hit with FT shooters who want an increased shot count. They are fun to shoot (longer)! They will fit into the Bantam Sniper HR/XR and any other side-mounting Brocock.

Very reliable and well built. Designed and built by one of the best mechanical engineers I've ever worked with at our robotics firm; they are amazing pieces of functional shooting fun! Now available in stylish blue, or now jet black.

Limited quantities so limit 2 per customer.
$85 each. PayPal payments only. (FF or you cover their fees)
Shipping CONUS will be done within 24 hours of order. Flat rate of $6 per order.
PM with questions

Thanks for looking...

rcs9250 · Aug 24, 2023

I was just reading some posts on thread:

Are all guns accurate?

I didn’t want to hijack the thread so started this one. You often read ”My new Mod XXXXXX shoots like a laser” or “My new Mo XXXX is a tack driver”.
What constitutes or is the criteria for both descriptions ? To me laser and tack driver would be like photo below, consistent group with a first pellet followed by the rest grouping no more than 2x the pellet diameter.
And as we have learned, every barrel will have a preferred pellet for ultimate accuracy. Some air guns are inherently accurate and are typically upper tier in price, which should be expected but what criteria constitutes laser and tack driver ? And at what distance ? Everyone knows group size typically expands with distance. To me, a tack, a lot of times that I’ve used tacks, they are a touch bigger or same size as a .22 pellet. So every shot would be dead on or at the worst, shave lead as it grazes the head.
Just curious.

sjs · Aug 24, 2023

I keep reading folks saying they use the barrel latch not only for opening but also for closing the barrel.

Is This ?:
1. Necessary
2. May help some with long term wear
3. Just to be safe
4. Overabundance of caution
5. Other

PNW1985 · Aug 24, 2023

Ready to sell off my collection. Not enough time for the sport. $800 each or I’m willing to make a deal on the collection. Shipping will be on you. I also have a spare 17” .25 barrel and a 24” .357 barrel for the WAR guns. I have a ton of ammo I can make you a deal on as well. You can text me at 509-993-9105 and we can chat.

WAR Flex .22 with 24” barrel, one mag and now has a 480cc tank. COBRA regulator with Cothran valve and WAR moderator. Burnt Bronze Cerakote.

Veradium Air Taurus. About a year old. I just purchased off the forum. Gun is a blast to shoot and very accurate. The gun will come with a Moderator adapter and cleaning rod.

Jesfranco · Aug 24, 2023

Price = $220 + split shipping

This is a Beeman R1 in .20 caliber . I get it in as part of a lot . As you can notice is completely disassembled . The only parts missing are the sights (front & rear) . The barrel , tube and stock are sanded .

Fill free to ask questions .

Thanks !

jpgrifles · Aug 23, 2023

Hello all.
New member here from Bakersfield California, my favorite air rifle of all time is the daisy Red Ryder I usually keep one in my shop to give to kids with parental approval, after trying out PCP rifles, I've gone back to my Beeman R9 springer for varmints.
I am also a long-range benchrest shooter and Custom Gunsmith building Target and hunting rifles.
I typically shoot ground squirrels once a week out on Ranch lands in the foothills east of Bakersfield using centerfire, rimfire and my Beeman.
Ya'll have good evening.
T L Johnson

cavedweller · Aug 24, 2023

Sold

I have 1 Element Nexus scope for sale: $850.00 plus shipping @$25.00 = $875.00 all in.
Priced for immediate sale! these retail at $1500.

5-20x50 MRAD FFP IR scopes with the APR-2D reticle - in OEM boxes - 30 mm tube body - Japanese glass!

Neoprene covers included with the scope

Appearance and functionality = 9 out of 10, I am subtracting one point for handling and scope ring mounting marks if any.
Used only at my indoor heated and cooled bench.
I’m selling all my hunting related gear to focus on field target related activities and equipment.

If you need 30 mm scope Ring’s we can discuss.

sometimes the fastest response comes from a text
Text me @: 251-610-8582

Email and paypal is: [email protected]

PayPal FF preferred
Venmo: Rudy-smith-15
I have lots of positive feedback

Everything ships quickly via UPS and will be well packaged and insured with signature required.

goatee · Aug 24, 2023

do you use them? do they help with barrel rigidity?
these air bottles can be so long today and they are so close to the barrel, you would thing it would be an added bonus for strength and rigidity.

Filnez · Aug 23, 2023

I recently ordered the JTS Comp 1 portable compressor from Pyramid Air. It came packaged in a heavy cardboard container with a Styrofoam block inside containing the compressor and the accessories. I ran it on 120 volt AC, not tried on 12 volt DC yet. It operates quietly enough that with it running sitting on my bathroom vanity two of my cats sat there looking at without being frightened off. That's pretty quiet! The fans whir and the compressor goes doop doop doop doop doop, not disturbing at all. First run with the hose plugged up to 4500 psi revealed no leaks so I bled the hose and got my probes out for the Evanix and Weihrauch rifles. Both reservoirs filled quickly from approximately 100 Bar to 200. The compressor came with some tools and spare parts. There is one fault, the fans come on and off with the power switch not with the fan switch button which does nothing but this doesn't hinder operation. The compressor is actually smaller and lighter than I was anticipating, not bulky or heavy at all, very easily portable. I have done 9 fills with it so far. The air exhausting from the case never felt warm. As it will be used to fill guns and not tanks (unless I change my mind and decide to spend even more money) it should last me a long time not being ran up to 4500 psi stressing it. Since it's brand new I can't comment on durability, that will have to wait on time. So far the JTS Comp 1 does seem to live up to expectations. I've already gotten to shoot a lot more than I would have without the compressor.

wickedwoods · Aug 23, 2023

Regular .357 benjamin bulldog Like new, includes one magazine, $500 and that includes the shipping cost.
Located in clarence center ny

View attachment 20230818_164413.heic

View attachment 20230818_164501.heic

View attachment 20230818_164420.heic

airrob · Aug 23, 2023

Brocock Concept Lite XR in .22, before the newest redesign. The best version they made.

Includes a bipod, multiple CARM 3D printed magazines and 3D printed case, (Best) UK filler probe, scope rings and Donny FL Tanto silencer. Prefer pick up NE Ohio but will ship for extra $$.

Payment via Venmo or cash.

olsenjb · Aug 23, 2023

Newbie here...just getting into PCP. I'm wanting a .25 and was thinking I'd definitely want to shoot slugs, but now I'm wondering if I'd be perfectly happy with pellets?

It would mostly be used for varmints (squirrels, rabbits, rock chucks, maybe occasional trash panda) and birds. It wouldn't be super long distance...but maybe stretch it out to 100 yards occasionally.

Thoughts?

Crabbypatties · Aug 23, 2023

Sorry slug guys this is a pellet post..lol My favorite is the polymag hands down! I haven’t found anything that’s more destructive and I have tried just about every pellet made. The hades are cool too but have you read the lid on a Polymag? #Facts

Cotton-Eye · Aug 23, 2023

Hi All, I have A Gen. 1 .22 cal Marauder rifle. It has always drilled tacks. I replaced the barrel a couple years ago with a Walther Lothar barrel (after a friend buried several pellets in the stock barrel. Once again, was always a tack driver. More recently, the trigger broke and I replaced it with a solid steel trigger that will never break (unlike the fragile and cheap stock triggers). It was still shooting very accurately after the switch out. I didn’t like how I had so much play in the trigger, so after a few weeks I decided to adjust the sensitivity and accidentally broke the sear (same cheap material as the stock trigger). I think it was because the rifle was charged (I didn’t degass it this time) and as I was unscrewing the assembly, it caused the seat to fracture. So I ordered a new sear, put it all back together again, and now every shot is way off center in every direction. Sometimes left, sometimes right, sometimes up, sometimes down. My sight is a Sightmark Wraith that has always zeroed perfectly with only a couple of clicks but isn’t able to zero at all now.

Did I damage something when I first pulled the trigger assembly off? Did I put the assembly together wrong somehow? Could the digital sight be going haywire? I’m really at a loss here….

Crabbypatties · Aug 23, 2023

I see a lot of videos of guys pesting or whatever at the same locations with plenty of targets. When I shoot a bird or squirrel they clear the hell out and don’t come back for some time. I’m talking like weeks what gives?

Kilmouski · Aug 23, 2023

I think all air gun sellers should at the very least provide schematics which include o-ring dimensions and properties. If they do not, we should boycott them. People should not have to spend countless hours figuring out what o-ring works on what air rifle.

Folks, this is simply stupid! We need to demand that the sellers of the air rifles we buy provide us with valid specifications for all parts. If they do not want to do that, than we will simply not buy.. The days of sellers over users, are over!

Shortcut · Aug 23, 2023

If anyone is going to the Pyramyd Air Cup and looking for Crown MK2 VP .22 500mm Barrel FX can moderator and 2 mags $1,200 pm me and I will make sure to have it with me. I also have a .177 barrel Kit Extendable shroud w/ mag in $170
Also have a brand new Arrow barrel kit for the Crown or Dreamline. $80
Last but not least I have an Element Helix 4-16x44 FFP APR-2D MOA scope $325

PM me and let me know.
Not interested in shipping cash only.

Sonny Helms · Aug 23, 2023

Pending

This pistol is brand new never been fired. I have heard good things about these pistols they shoot slugs or pellets and you can adjust for the FPS you desire. Well it's just not me so I will let it go for what I put in to it. I will consider trades just no low balls please. The price is firm 1,250 will consider trades but nothing too old or all dinged up. If my hands were a little bigger I would just keep it. saw some shooting theirs 50 and 100 yds. If you are in to pistols this one is very nice. So 1,250 firm and i will pay half the shipping or unless you have something I would like in a trade.

AirNGasman · Aug 23, 2023

Here's a link about RAW's new air pistol!

NEWS FLASH SCOOP! "A giant leap for"... Pistol Field Target! (spy photo included)

Having for some months heard rumblings (from a semi-reliable source 😂) about possible considerations from one of the top FT rifle manufacturers to produce a new field target pistol, I knew better than hold my breath that it would (ever) become reality. IT'S REALITY! As the founder of Pistol...

www.airgunnation.com

View attachment 382976

DeanB · Aug 23, 2023

Just bought this Airacuda and no problems so far and no complaints except for I ask Pyramyd Air if they carried any parts for them like hammer spring etc and they said no and dont know if they will ever get any.
Well I emailed JTS and ask them if I could buy parts direct from them and the response was we dont sell parts.

Deleted part of thread to fact check. Trying to find thread about parts availability to make sure I read it correctly.

Hot

Hot

Umarex Notos Moderator is loose

Events Pyramyd Air Cup

Traditional Pistol SOLD EXTREMELY RARE - Brocock BACS Model 1851 Navy .22

RAW Rapid HM1000x question

Magazines WTS 40 shot Brocock magazines now available!

Are all guns accurate?​

HW/Weihrauch HW35 TLC

PCP Rifle NLA UPDATE Selling off my collection $800/each.

Traditional Rifle NLA Beeman R1 .20 Project - “Sold to Mark Ellingsworth”

Optics SOLD Sold - Element Nexus 5-20x50 FFP APR2D MRAD

N/A barrel bands,, yah or nay

PCP Rifle SOLD Benjamin bulldog

PCP Rifle SOLD Brocock Concept Lite XR .22 Loaded $850

Benjamin Marauder accuracy issues!!

N/A Demand fair treatment!

I think all air gun sellers should at the very least provide schematics which include o-ring dimensions and properties. If they do not, we should boycott them. People should not have to spend countless hours figuring out what o-ring works on what air rifle.​

PCP Rifle NLA FX Crown VP .22

PCP Rifle SOLD Brand new Huben GK1 .25 Cal pistol Pending

JTS JTS airgun parts

Filter

Are all guns accurate?

I think all air gun sellers should at the very least provide schematics which include o-ring dimensions and properties. If they do not, we should boycott them. People should not have to spend countless hours figuring out what o-ring works on what air rifle.