FX Crown MKII with three separate calibers. The .177 caliber has a Superior liner. The .22 caliber has a Superior liner with a carbon sleeve installed. The .25 caliber has an STX liner. Included in this package are a magazine for each caliber and the correct FX probes. There are two very small marks on the stock that I’ve shown in the pictures. I’m the second owner and when I received it, it had a small leak so I sent it to FX for a complete re-build. It has held without any issues since then. The tank is dated 2018/12. The last picture shows the Crown and accessories packed and ready to ship. The box is not an FX box. The two orange items are the barrels in flannel protective sleeves. This is an extremely heavy package so I’ll only ship to CONUS. I’m asking $1600.00 and I’ll pay for the insured shipping. PayPal friends and family is preferred but I’ll also accept a money order or a check with a hold for clearance.

Bought this .177 RAW from a competitive shooter a couple years ago who won USARB nationals and other events. Made by Martin and comes with a Sightron 36 target scope. I'm not shooting it and it deserves someone who likes high level competition. $2200 includes scope. You can contact me directly at [email protected].

That everyone copied everyone again. All these pcp guns coming out with the air tank around the barrel.

Personally, I'm okay with that to a degree, but I'd have liked to seen some more affordable semi auto offerings in rifle/carbine formats. At least most of them caught on that we're getting tired of the plumber fitting/super soaker bullpups.

What do YOU guys want to see in the future?

problem resolved.
sure wish they took phone calls though.

It's definitely a M30 with a different stock. So JTS...FX...Barra ...ok who else??? Hey Benjamin make a Marauder like this!!! 35 shots per fill on the BARRA... interesting ..
Video link below..

Hey AGN. Check out my video showing my attempts at sub MOA groups, 5 shots, at 50 yards, with this budget-friendly .177 Air Venturi Avenger shooting pellets!

SPOILER ALERT
It is definitely capable of sub MOA as shown in my video. 2-out-of-3 5-shot groups are sub-moa. Time to push it out to 100 yards.

Selling some of my impulsive acquisitions, everything in VG condition. All are .22 caliber
Split SHIPPING I use Pirate SHIP least expensive cost.In the picture top to bottom are item #s listed

***SOLD***#1-Talon pistol/carbine, 28" overall length, weight 4.0lbs ------------------$340.00

***SOLD***#2- Talon with 20" barrel, Altarus regulator,(scope/rings NOT included)Trigger guard now installed---


***SOLD***#3- RED Condor SS, Talon Tunes? moderator SUPER QUIET-----$430.00
***SOLD***#4- Kral Puncher Breaker, 27" overall length, Bull Pup,3 magazines, fill probe.---------$270.00
***SOLD***#5- Tactical Zobroia Kozak, (NOT Bull Pup) 2 magazines, fill probe. just resealed ---$520.00
***SOLD***#6- Mad Dog stock fits Talon---------------------------------------------------------------
SHIPPED $80.00 NOW $70.00

I aquired this rifle from the original seller just under 2 years ago, shot about 9 rounds through it and its been in the safe since.
This rifle is 100%

It shoots Lee 113 grain .309 at 860 fps consistently

The stock is custom made from Loren @ diamond gun stocks to fit the 580cc cf tank on the rifle. The rifle also has a talon tunes heavy hammer spring. I have receipts for the stock , that was just finished in January.

The rifle groups very well at 65 yards (see pics)

The rifle also has a Rocky Mountain Precision Airguns roller bearing trigger with 2 pound spring installed and I removed the auto safety (can still engage it manually) and I still have the auto safety to reinstall.

If you want to run a moderator no issues or adaptors required as the barrel end is threaded.

The rifle comes with the bulldog tact soft case which fits it very nicely or i can ship in a hard case your preference.

If you were to duplicate this brand new with the regulator , stock , rifle, etc., etc you'll be well over $2300



I'm selling the whole package , rifle, stock all the mods hard case and the Lee mold , the rounds I have cast for $1100 and ill cover shipping to lower 48.
PP FF, Venmo or money money order or cashiers check.
I'm only selling because its too beautiful and too good of a rifle to sit in my safe.
Text 980-505-3124 or DM with questions

Hey, pretty sure RTI is there. I haven't saw any news from their booth.
It's been a year since we were teased with the "Mora".
Can someone please swing by and see what they have?
Pics or video would be awesome but just a response with basic info would be much appreciated.

This past summer, for the first time in 5 or 6 years, my FX Boss started acting strangely. Got together with Mike Bricker (Centercut) & he helped me tear it down, re-seal it & gave me a newer OEM reg to fix the problem. Ultimately, it did not help. Mike suggested I try a new Huma reg. My Boss has ALWAYS been incredibly accurate, shooting JSB, 44.75GR Diabolo pellets but that is the ONLY pellet it would shoot. Never had any luck with Hades, Polymags or 50gr Diabolo. It just wouldn't shoot them well at 835-845FPS. Got a Huma reg (very fast response & shipping, 3 days) & installed it. Aside from installing it backwards the1st time (it goes in OPPOSITE from OEM reg) the process was easy. The most time consuming part was tuning it & even that wasn't bad. My Boss is shooting around 885-895FPS now. Accuracy is still superb but here's the part that still blows me away & makes me smile. It now has the power to ACCURATELY shoot Hades, 50gr Diabolo & yes, even Polymags accurately (& of course the 44.75 Diabolo) but what I NEVER expected was the shot count. I used to get 3 to 3 & a half 9 shot mags. Today, out plinking, I shot a full 6 mags, 54 shots! Literally DOUBLE what I'd get before! Howzat even possible? Always LOVED that gun but now it's even BETTER!!! THANKS for suggesting the Huma Centercut! Best $88 bucks I've ever spent on airguns.
Gerry

I went out to do some ground squirrel hunting on a permission with a big problem. The BRK Ghost is just an awesome accurate air rifle and loads of fun to shoot.

Enjoy

I want to say THANK YOU for the above and beyond service but for anyone reading this, I'm not promoting that Custom Magazines is in the habit or having a responsibility to do this.

I reached out to them to see if he could create a magazine based on an existing rifle but not in a factory caliber. Darko responded that he would see what he could do but it might be a few days because of other commitments. Well, he got back to me in 2 days with a pic of the prototype and a promise to test it. Two days later I had ordered and they were on the way on the next day... AMAZING ... he even offered a single shot tray and loader, which I was happy to scoop up...

Here is the result...


Now this is something that many have inquired to Tom of AAA about but I took it upon myself to try... a 177 P-EVOL. The idea is an EVOL for AAFTA and EFT pistol ft events. The Mini would have been the perfect choice but I only have a gen 1 Standard. With a couple of parts from Tom and my own valve, I was able to get it down to 12 ft lb at 1400 psi and this 12" barrel and shroud that I made and fitted. It is 24" overall and the barrel assembly is 14.5" with the fore end depth less than 3". At 1700 psi, it makes 20 ft lb easily. The short tube will be fitted for appearance and balance when I can acquire a different guage block. Mine is early gen 1 and my guage block won't fit this tube.
It's pretty amazingly accurate and VERY pleasant to shoot in rifle form and gets a huge number of shots on the current reservoir.
I also fitted a 15" barrel to test with and use the original tensioning shroud...

Fun project...
Bob

After all the hypes on YouTube about ppl praising Fat Boy 2 as the next gen of moderator that is caliber interchangeable and the bulky but short dimension seemed to please these YouTubers with the sound attenuation without the tube extension, and the claim that the tube extension would bring the bark down to whisper quiet.

So I bought it with the extension tube.

I was surprised that the Fat Boy 2 without the extension tube produces loud and sharp bark. The extension is heavy and attaching the two does reduce the bark but at a level that is not proportional expected compared to the volume.

I tried to add layers of thicker insulation material to the core in the Fat Boy and use hair curls as the frame to roll the insulation with no substantial improvement.

Do I have a bad luck or it's just what Fat Boy 2 all about?

Anyway, I'm looking for the alternative which able to accommodate both cam 22 and 25, light and no bs bark attenuation and the length should be less than 20 cm.

Please advise.

Thanks.

One lot consisting of pellets and slugs.
180 49.5 gr .300 NSA slugs
250 44.5gr .30 Impulse Air HBT
200 47.2gr .300 NSA slugs
200 50gr .30 FX pellets
500 44.5gr .30 JSB Hades
300 48.6gr .30 Hatsan Vortex Strike pellets
$50 plus shipping

Ain’t Mother Nature neat!

Evening everyone,

I ran into a problem with my Beeman AR2078A a few months ago. I use this rifle exclusively for shooting CMP matches, bought just for that reason. It’s been a good accurate rifle especially if I’m shooting well. I went to a match in October if I recall and had crappy day. I had shot a few 1” groups in practice but at the match it opened up to about 4”. I wrote it off to a bad day. The next month I didn’t practice much but it was worse. In addition to large groups I only barely got 50 shots instead of the usual 65 or so. Being CO2 powered I made sure the rifle stayed in a warm controlled environment. I didn’t shoot it again until today. I ran some cleaning patches through the barrel to make sure it was clean, loaded up 2 12mg CO2 cartridges and started shooting. Temperature was about 70. The group sizes got much better but everything was about an inch left and 2 high. It stayed consistent and delivered 70 rounds. Could cleaning the barrel have made this change? I can rule out temperature variations as weather was shirtsleeve warm which is normal when I shoot this rifle. Same pellets as always. Could something else be going on? The learning curve is still pretty steep for me but I’m getting it figured out. Thanks.

Rick H.

Ok, I’ve finished the HW 80 hunter I built (I’ll checker it after a month of drying) . I wanted to keep it stock strokes to try to see what it’s about..

( I’m working on a stroked version as I feel 5 mm more and it might be the best gun there is at it’s power, and stroke to cylinder ratio..more when that is further tested) It is a gun that’s built as good as it gets. When HW changed them front welded brackets witlh a spring loaded machined one that holds the arm tight at battery cocked. Along with the new cocking shoe. There IS NO AIR RIFLE that is as well built . Now it can benefit from some work as I have done. The factory seals are always parachute to support the guaranteed idiocy of the average shooter .
Remember, they are selling to mom and pop for jr. too. Not this type of airgunner.

This Mongoose has been reshapped in the breech block to match the chamber and sight screw holes filled with screws. I’ve welded them ,but you end up with heat transfer lines. I don’t mind the hairline screw lines . The best are the K breech blocks with none. The barrel was shortened to 11 inches. It has been recrowned and mildly choked with a full length shroud and … well it’s not empty in there.
I did do a slight bit of port shaping. Along with a new piston seal I made. (most Hw are tad smaller than 30 mm, 29.89.actually)
The spring is a smaller wire. .135… WHAT YOU SAY.. All them kit makers use .142 to .148 wire In their kits… It is easy to get a stout wire short stacked and tight wound to give a snappy cycle .. At THE COST OF YOUR ARM . Sadly the HW80 has a odd breech block to cocking arm ratio. It’s just out of what I refer to “the golden ratio” [I’ll post on that later, something I’ve found with the best guns for ease of cocking to power ratio. To breech block to arm ratio, THATS WHERE THE EXTRA 5 mm stroke will come into play]

The piston was carbonitrated,At the rear.. buttons are one way to center the piston . You need to indicate it and center the rod and re pin it with slip fit guide and it can’t move. The spring and guide are my own Designs.
The action and barrel have been bead blasted and reblued to a satin finish. It is a hunting weapon
The stock, yes ,I saved that for last.. it is a Venom inspired design from a local tree that was cut 25 years ago.. Its not my fanciest wood but sentimental , Yes.. it is a functional hunter stock. Albeit the front screws look like every Tx ,they are not. They are pillared with metal sleeves just under the wood to let the screws go flush while the metal braces against the machined brackets. (You could never get away with that ,with the welded brackets , they all stripped and you were re tapping and using cups in the stock) I prefer less outside,especially flush, to see the wood not brass rings or stainless steel

It’s shooting 14.66 ftt at 780 fps just a hair under 20 ft lbs with very little recoil. YOU WILL ALWAYS HAVE SOME,in a spring gun as it’s physics.. You can’t beat it. With the lighter spring cocking isn’t arm breaking like big wire. Trigger is ,well ,Rekord. 1 lb .

One thing I will be doing in the ne’er future is welcoming full open build specs as well as as much help as I can to those who want to try these builds on their own. I’ll tell you EVERYTHING IVE DONE. Remember, I can give you grandmas cookie recipe, not sure they will taste like hers..
I do not do this for any business or money as a tuning so called master or for profit. Been der done dat. Not worth it
Manny may be offended as they call balk and be offended because they think their knowledge s value, when in reality it’s fruitless . First ,it turns the many younger potential AIRGUNNERS away as they can’t afford these lustful guns. Give them hope and a bit of encouragement and we grow new AIRGUNNERS for the future of the sport..
Second, knowledge Is power, but what is knowledge if it’s not passed on..
Third, there is no money in truly tuning air rifles, the time spent on one gun that gives you fits can tie up a week worth of work.
TO THE GUYS WHO CAN MAKE $ kit dropping and de buring with new seals for $300 go for it..

I am looking for help in deciding on an air gun for indoor handgun practice. I am a long time handgun shooter. I take my shooting seriously, having owned numerous fine shooting handguns over the years including a S&W M41. I currently shoot my Freedom Arms Model 97 revolver, which I dearly love. I also shoot my Diana 5G springer, which I find to be a fine pistol with the caveats that it is a PITA to cock and I find the recoil to be a bit annoying. It is, however, accurate enough for my needs and has a decent trigger and sights. I don't find myself shooting more than about 15 rounds before I become annoyed with shooting it due to its cocking effort. Here are some of my requirements and wish list:
* I do not wish to be saddled with a scuba type tank. A hand pump is not an objection if necessary.
* I would like it to be comparable in accuracy to my 5G.
* Good adjustable open sights are required. Being able to add a red dot such as a Fastfire III in the future would be great. My eyes will not last forever.
* I do not shoot in weather extremes.
* I do not compete.
* Maintainability/availability would be great
I really don't have objections to paying decent money for a good pistol if necessary. As I said, I take shooting seriously. Model 41s and 97s do not come cheap, but if there is an outstanding bargain that meets my needs, so much the better. I hope I am being realistic in my wants. Thanks in advance for any help you can provide.

[No trade offers on this listing please...]

Hello AGN,

I'm looking to sell a very nice Edgun Leshiy 2 Long Hi-Capacity w/ 0.25 Caliber 350mm Alfa Precision Barrel, REPR regulator, 360cc 315Bar CF bottle, 2 BLACK magazines w/ updated (easy to remove) magnetic mag covers, Leshiy Black Out Kit, Jack.K magnetic magazine holder & regulator adjustment tool, magazine speedloader, extended locking pin, Edgun fill probe, DonnyFL Leshiy 2 shroud & original Leshiy 2 box.

This Edgun Leshiy 2 Long Hi-Cap REPR sells for $2,870 plus tax & shipping from Edgunwest.com. It is currently set to shoot JSB 25.39g pellets at ~820fps (which is about 38ft lbs) but I can set it to shoot at whatever fps you'd like within reason (or you could do it yourself, it's very easy to adjust the REPR reg). A DonnyFL w/ UNF 1/2x20 is included with this rifle so that you can swap out the factory shroud and add a moderator of your choice to reduce the report on this rifle (for example: a DonnyFL Ronin or Fatboy 2.0 or Huma Mod50 fit perfectly with this shroud). This rifle is in excellent condition with only normal light wear on the edges at the normal spots like the scope rail, trigger guard, butt-stock, etc. as shown in the photos; the air tubes, factory long moderator and DonnyFL shroud have all been carefully wrapped in an automotive grade carbon fiber vinyl wrap that looks great but can also be easily removed without any residue if you don't want it.

To summarize, this awesome L2 package comes with everything listed below:

• Edgun Leshiy 2 REPR Long Hi-Cap 0.25 Alfa Precisioon 350mm barrel w/ upgraded 360cc 315bar Wolfiek Group carbon fiber bottle
• DonnyFL Leshiy 2 Shroud w/ UNF 1/2x20 end cap
• 2x BLACK 8 shot 0.25 magazines w/ updated magnetic cover
• 1x Jack.k under the scope magnetic magazine holder
• 1x magazine speed loader
• REPR regulator adjustment tool
• Edgun Leshiy 2 Black Out Kit installed
• Extended locking pin installed
• Edgun fill probe
• 2x extra pucks
• Carbon fiber vinyl wrap on factory moderator, air tubes and DonnyFL shroud
• Original Edgun Leshiy 2 box

[Scope and mounts shown in the photos are NOT included in the purchase price...]

As configured with the extras listed above, this setup would total around $3,300 after taxes/shipping . . . so asking price here is more than fair and, therefore, firm.

Price here is FIRM at $2,000 + 1/2 actual shipping

Local pickup is available in the SF Bay Area - otherwise, payment by Paypal Friends & Family is preferred (or add 3.5% if using PP Goods & Services). I have plenty of feedback both here and dating back to the Yellow Forum so please feel free to do your due diligence and know that you're dealing with a reputable trader.

...I just bought a .22 Ghost HP and found the action lever to be quite sloppy...is this normal for the Ghost...?!?...is there some remedy...???...

...I don't have much experience with these new-fangled lever action repeaters...do most of them have this much play in the lever...???...

...I do have a "Benjamin" Cayden and an Air Maks Caimen, and both those rifles have a lot less slack in their lever arms...

...their combined price much is less than that of the Ghost...

...the Caimen is downright snug compared to the Ghost...

...I am not sure that it is something I will be able to overlook going forward...I would like to think I would just get used to it, but fear it may bug me every time I use the rifle...

...if it were not for the tiny five shot test group AoA produced with this rifle @ 20 yards, I would have already returned it...they tuned it well for JSB 18.13 grain pellets for me...

...AoA has issued an RMA # with no restock penalty...the only cost I would incur would be shipping...Chris @ AoA rocks...!!!...

Just can't find anything to make it better.

SOLD

I have two Leshiy 2 and selling one to fund other hobbies. Purchased last September, 2023. Absolutely a beast gun. I had to tune it down to shoot .25. No flaws/issues, like new.

Leshiy 2 REPR 9mm re-barreled to a .25, 350mm barrel

All pictured are included.

Behemoth Tri-lug moderator
7 magazines
Speed loader
460cc or .46L bottle
Muzzle Brake
Plano case
Valkyrie handle
3 pucks

Asking $2000 shipped to your door within the USA.

FX pocket chronograph V2.
The V2 is the latest and greatest from FX.
I bought this new and used it for 1 week.
I decided to upgrade to the more expensive FX True Ballistics Chronograph.
My loss is your gain.
$220 includes USPS Priority shipping.

PayPal Friends and Family or Venmo only.

You can check my AGN member profile to verify a clean and safe transaction.

If I don't respond to your PM within a few hours, send a text to 415 350 5282. The AGM PM feature does not always work.

Rod in San Francisco

Looks like the trend this year is how close to a powder burner can ya get AND air reservoir around the barrel.

I like this over the DRS or whatever the FX one is.

Just completely rebuilt using genuine Feinwerkbau pump head and all seals. Properly lightly lubed with Feinwerkbau grease. Gun is in very nice condition and was privately rather than club owned. Typical Feinwerkbau accuracy. Trigger is of course amazing and action is as tight as new. Asking 750.00 shipped CONUS. PayPal F&F preferred.