Does anyone have a Chart with BCs of .22 pellets.
If there is not one out there already. It would be nice to make one and put it as a sticky up top as this information is priceless
and time consuming to figure out.

I did a search but could not come up with a chart.

Daystate

Air Arms

I figured to repurpose these plastic drums to a spent pellet catch. Seems to be working . Leaf trash from the trees seems the only inconvenience over time , but should be easier the raking and scooping off the ground.. time will tell.


The few caught test pellet .177& .22

Got up early and beat the wind to the range! But not by much was dead calm when I got there. Got setup and the wind showed up
Nothing crazy like wind but breezy.
Was able to acquire an old pizza pan from work; so I utilized it as a 100y target
Started slinging away
Got all of the slugs to hit the 100 yard mark
A few even went THROUGH the pan!!
Slugs are NO JOKE when it comes to carrying that energy and smacking right through metal at 100yards!
I was NOT expecting them to go through at all.
Set targets at 15, 35, 50, 75, and 100yards.
Was able to hit them all quite easily with slugs compared to using a pellet. Was able to watch the pellets drift in the wind by about 4 hash marks in my scope from POA.
At that point it was getting quite windy, and the Lothar was low on air...
Toted the 880 along to see what she could do against the Lothar.
While accuracy wise she could keep up(more holdover and windage) but she just didn't have the oomph to do much damage after 75 yards.
However.....I WAS able to consistently smack the 100 yard taget with the 880. Leaving very little dings for damage.
Anyways; enjoy the pictures and videos!
Had a blast even though it wasn't for as long as I hoped it would be.

My BRK Pathfinder in .22 was getting an inch and a quarter groups with Nielsen 17.5 grain slugs at 40 yards and I thought that was the best it could do. All the other slugs that I had available to me had groups worst than that. ( groups shot with red dot)
And then...forgotten in a corner I found a lonely zip lock bag with a small sample of 16 grain AVS polycore slugs. Tried those and put 5 slugs in a rugged hole. And then.again. And again. My last few slugs I put over a chrony and they turned a very respectable 24.5 FPE.
And then the disappointment...AVS no longer produces those slugs. If anyone out there is reading this and happens to have a stash of them please reach out.

m3 impact . lots of Xtra. tried to slug it but failed. 30 cal. have every part for 22 cal with new heavy liner but never used.has the smaller brass hammer in it. also bought two new carbon liners. 22 30. put barrel tensioner and screwed up my moderator. I'm just tired of it. I Use my other airguns and just gave up on this. please no endless questions. I don't know how to ship so local pickup only. has everything in pictures helix scope. 1200 bucks. will set up for pellets for 200 bucks otherwise I don't want to touch no leaks. reg dealeat.

Up for sale is my Air Logics Genisis .22 Cal Single Stroke Pneumatic. There is less than 12 in america and only 150 made in england very rare and this one is in very nice condition. I am asking 1500.00 for this rifle it is very rare you will probably not see another one. phone number is 860 992 2527.

I have for sale a fx barrels/ other goodies
Fx 600mm 357 with probe and mag 300tyd
Fx 600mm 30cal with pellet liner and heavy liner and carbon sleeve and mag/pellet probe 400tyd
Fx 25 heavy liner 600mm tyd
Burris fast fire 4 Red dot 300tyd
Leupold freedom 1.5x4 200tyd
Message me and I can provide pics thanks god bless!

Done some shooting yesterday with my Tiapan vet long with 22 redesigns at 75 yards. Shooting 910 fps. Shot a couple times to get centered on target then shot one five shot group that was .635. Then two groups with .25 cal impact 33.95 then three groups with hiM Is all at 75 yards and one group at 110 yards with mkIIs. I was happy to say the least!!

ForSale: As new Sniper HR.22 in perfect condition. 2 Brocock magazines, 2 Brocock single shot adapters, one Carm mag and one carm single shot adapter and one Element magazine. Includes picatinny raised rail. Scope and mounts not included. I'm selling to fund a benchrest rifle. Everything works perfectly and shoots like a laser. $1000 plus shipping
Photos upon request.

Warren Peppered Laminate Grip (BNIB). Retail $250, asking $108.



Prices include shipping to CONUS, HI, PR. I prefer Zelle, Venmo, PPFF.

.22 - .25 Badger kit: CF hand guard with adapter & hardware, 5 stack Huma-Air Mod 40, picatinny rail adapter (for use with 350mm barrel). Retail $275, asking $125. SOLD


.17 - .22 Valkyrie Tishina kit: Aluminum hand guard with adapter & hardware, Tishina moderator with shroud (for use with 350mm barrel). Retail $275, asking $125.



17'' CF hand guard with adapter & hardware (BNIP). Retail $275, asking $125. SOLD


Prices include shipping to CONUS, HI, PR. I prefer Zelle, Venmo, PPFF.

Any body have pictures of this event ? please post .
Thanks Stan

shown here John French bestows Lexi Linder with a royal gift for winning the 1st ever Squatchbomb challenge.


Audio: lorde - Royales

***MOD EDIT:
Thread locked for Rule #3. Unsafe operation.

Lasers are extremely dangerous to the user and ANYONE who may be exposed directly or indirectly by reflection. There can be immediate and irreversible damage including blindness from even incidental exposure even at long distances. Airgun Nation cannot permit such unsafe practices. ***

Hey all - just a word of warning - be very careful the type of laser sight you put on your PCP. I picked up a blue laser off Ali Express for my Notos and evidently it is one of the higher powered ones. As I was sighting on a squirrel it went up like a tinderbox. Thankfully I was able to dispatch it before it started a fire but FYI and be careful with the laser sights and pointers!

My regards to all members ! May i have to post something many many months but i am always here daily ,reading every interesting thread and enjoying our lovely forum.
There is a well known problem with the first gen impacts that can not fit inside the action the power plenum or the later 720 plenum .
I mean if you will try to upgrade it with any type of fx pp older or latest you will find a serious difference. Is going so tight inside the action clamp that you destroy always the 2 orings ( I think 9x1.50 , 90 hardness) .
In my case I followed the instructions of a well known airgun store of Spain which I have seen in YouTube.
Long time ago I recommend as well in one of my posts, the same method to some members who have the same problem .( now I regret for this and I apologise).

According the instructions of this store you remove the screw from the action clamp and you insert it and start screwing it from the opposite side by using the same time a metal round between to open the clamp ( I don't know how to describe the metal round in English language but probably you got me what I mean) .
I tried very carefully by turning 1/4 each time and same moment trying to insert the plenum inside without damaging the orings .
When I assembled the gun ,it was leaking instantly the air near the power wheel.
After many many attempts assembling and disassembling the leak remaining the same.
In the end I used a microscope I have for barrel inspection and I see inside the clamp a small line like a hair .
Suddenly I realised that outside of the action the crack was more visible . It was a crack in action .
That was the end . Oufff!!!!
I assume that aluminium material has very tight tolerance and is not elastic at all and I have the feeling that even if I was going carefully step by step in the end I passed the limits .
I leave and working outside far of my country and I have the change to enjoy my airguns once or twice per year in my vacations .
And now I was 2 weeks for Easter vacations ..
Without any second thought I called the official Fx importer of my country ( Greece) and I order one new action .
I was looking it in his website long time that was available one piece and was brand New for impact x .( same is mine) .
I started searching in airgun nation to confirm that this block it can receive the latest regulator bodies 10 mm and not the first gen 8mm.
When the vendor confirm that is writting on the action impact x I order it imediately .
I want to mention that his price on the site was 280 euros and he send it to me on north Greece for 250 euros including the transportation fee when the same time in other stores in Europe the price is 480 for the impact action older or newest .
Next day the new action was in my home .
The funny think ?
Saturday Easter night after 12.00 midnight I am starting to assembling the gun .
There is a storm in area and electricity suddenly is cutt off in all town.
I switch on few candles in the table and wearimg a head light .

I have disassemble honestly maybe more than hundred times this gun ( specially the first 2 years )but never I enter so deep in action like safelty small spring and metal balls .
After 2 hours working almost in the dark
Gun is ready and keeping air perfect .
I installed as well the new 720 pp and the new type hammer spring holder ( the shorter one 16mm,before I have the 18mm ) and newest hammer spring adjuster .
I want to mention here that my gun is full modified from day one back in 2019.
Polish power plenum , valve seat open 7.6 mm ,valve house tp to 7.6 mm , rear block tp 7.6 mm ,huma air brass double transfer port , pin probe handmade in lathe ,hammer spring from huma 57 cm ,hammer weight the latest type of fx and first time now trying the tungsten hammer ordered from ebay but same specs with fx .

This was a lesson for me about what can happen with so much tinkering but doesn't matter .It was an experience ...
We are lucky as fx owners that the market is full of spare parts . Even actions!!!!!

Long story short next day i am not suttisfied at all with the new 720 pp and I installed again the Poland power plenum and with the new adds ( new hammer holder and screw adjuster ,and tungsten weight ) the gun is a beast .
So far I was shooting Nsa 61.5 with amazing results at 990 fps .
Now with the new mods shooting a new round Zan 63 gr with same accuracy like before at 1058 fps .
Regulator 180 bar ,I down a little bit back the hst and closed the valve adjuster up to get the groups tighter almost at 3 and half lines.
I have a very short blast with a relatively low noise and speed 1028-1030 with a very good accuracy .
First game a crow at 110 yards .
The thump noise of zan 63 gr it was so instant at 110 yards that I didnt realise the 2 different sounds. You know the usually sound bam-thump!!!!
Completely one and instant sound in this distance with the touching of the trigger. Is a serious and noticeable difference in these high speeds from 990- to 1030 with a havy 63 gr slug .
I will post a card from strelok app with muzzle velocity at 1030 fps.
114 ft-lbf at 160 yards and 84 ft-lbf at 250 yards! Is scarry .......

Regarding the accuracy I didnt shot long range groups . But while adjusting the gun to find the sweet spot , when I managed to have many rounds almost hole to hole at 45 yards I knew I was ok .
With strelok up I am always spot on in long distances and I confirmed it by shooting small stones up to 260 meters .

Regarding my dissapoiment of the 720 pp is a very long story and I will open very soon a new thread cause if I will not find a solution with It I will not relax!
Gun 2 days after the repair .
Smoking some stones at 260 meters .

Last photo shooting an old love !
Wolverine 303 unregulated .
Since I got the impact 2019 is resting in the case ....and still keeping air !

Works perfectly and has a Huma reg installed. Shoots NSA 47.2gr @887 like a laser. Have taken many ground squirrels and rabbits with this setup. Everything in the picture is included in the sale, 2mags, original AGT moderator, scope and mount (VicOptics S6) , roughly 350 47.2gr slugs, and bipod. Also not shown is original soft padded case. Absolutely zero issues with this Uragan. Holds air and zero leaks. Went down the rabbit hole building ARs, need to feed that addiction now.

$1150 shipped. PayPal, Venmo only. Send a PM if you're interested. Thank you for looking.

I have a beautiful M3 600mm pellet liner .22cal Impact for sale. (too many .22's on the shelf)
Purchased new on April 16,2021 from Trenier Outdoors

It will be shipped in the original FX Hard case, including Magazine, Moderator, FX side mount for 2nd regulator, FX CF barrel sleeve (not glued), A modified Atlas knock off Bipod, Saber Tactical Arca Rail with Picatiny for Bipod, and Original Booklets,

Rifle shoots very well.
Located near Traverse City in Michigan for local pickup.

$1650 and would be willing to ship for $30 to Lower 48 US States.
Not Interested in out of USA shipping.

Hopefully photos attach, if you need more let me know and I will send to your cell, or Email.
Attached is a photo of a Fantastic 50 yard and 100 yard 5-groups, using 18.13 JSB ( never tried Slugs)

Hi. I bought a used NcStar Mark3 10-40x50 scope and trying to zero it in on 40m.
I started with 18x and hit low, I turned the knob "up" and had to turn all the way to the point it didnt go any higher and hit low 3 and 4 (red mark) but when I zoom in to 30x i hit black (blue mark) without adjusting the knob. I dont mind shooting with 30x zoom but utstyr hard to find targets at closer range. It looks like if I zoom out to 28x i might hit center tho, but this cant be right?

I seen folks use tap water distilled water, water wetter, Whats the deal is tap water fine followed with vinegar after a few months to clean up the mineral deposits, Is distilled water by its self bad, Do you need water weter if you use distilled water or should I just use tap water with ice.

Selling my crossman build to put the funds into a new project.

Trigger polishing and many small tweaks went into this little tack driver. Feyatchi optic and all the old parts included

Letting this go for $325 $300 $250​

shipped to anywhere on mainland USA. ​

No optic included

Gun and parts over $400 with taxes and shipping.

Build thread is on this forum. I'll try to put a link in this thread.

New crossman 1322 USA version 2022 (box)
Steel breech
Buckrail minimalist folding stock
Buckrail honeycomb grips
Buckrail plumper pumper
Buckrail suppressor
Crosman 1377 1322 SuperPack Pump RP Valve, Power Hammer Spring & Boss +25% Port
Extensive trigger work
Feyatchi red dot NO OPTIC INCLUDED
UTG dovetail to picatinny mount

I have been shooting springers for years and just bought my first PCP.
I ended up going with a JTS Airicuda Max in 22cal.
I wanted a regulated, wood stocked well built Multiple magazine PCP.
This one fit that bill. I was looking at an Air Arms S10 multi shot but decided to get The JTS to start with and learn about the
operation and function of PCP rifles. After this intro to PCP rifles I will most likely will purchase the Air Arms in .17 cal in the near future.
I ordered the JTS with an AirVenturi G9 Hand pump. It took 100 pumps to get it back to 3200 PSI yesterday. So far I have pumped it up twice.
The pump works very well but it does make you tired when you are 55 years old.
I was going to shoot after pumping it up but my heart rate was making the crosshair move around to much so I will wait for next day.
I have the new portable JTS compressor on order and should have it within a week. I think that will be money well spent.
I thought my Air Arms TX200 was accurate and fun to shoot but now I can see all the fun PCP guys are having and understand why. A PCP sure is different than lever.
I have only been shooting in my basement so far with the JTS but at 10 yards it is easy one hole groups ( I shoot with a rest) . I need to take it outside for longer ranges.
I like everything about the Airicuda Max, The side lever, the adjustable comb, wood checkering on stock, metal magazines all metal construction.
For the price point this rifle is amazing !!!!!!!!!!!!!!!!!!!!! Great first PCP for sure.
I will definitely be purchasing pellets more often now.
Looks like I am going down another rabbit hole !!!!!!!!!!!!!!!!!!!

Excellent condition. 37fpe. Very low shot count . Includes 1 mag, fill probe and 1/2×20 moderator adapter. Has extended bolt handle and original is included. She holds air and cycles perfectly. 15.89 Hades @995fps for 34fpe. 18.1 gets 37fpe. I have some 17.5gr NSA slugs arriving tomorrow so will update about velocity and feeding. Pictures will get posted soon. Please CALL OR TEXT. 503-504-708 four. USPS MONEY ORDER ONLY. Thanks for your time, Bill and Addi.
.UPDATE☆☆☆UPDATE
NSA 17.5gr make 944fps.

This is one of the test units. It's been shot on multiple rifles and does not clip.
Shot it yesterday on my Condor. Works good.

Carbon Fiber and PETG plastic moderator.
1/2 x 20 UNF threaded steel insert

Size: 5" (129mm) x 1.2" (30mm)
Caliber: 22
Thread: 1/2 x 20 UNF
Weight: 2.1 oz.






USED: $45.00 to your door.in CONUS only.
I will ship OCONUS but we will have to work out shipping.

PayPal only. I will invoice you via PayPal once I have your Email Address.

Money back upon return if you are not pleased for any reason.

Being a lefty is hard sometimes. Thankfully some companies put out accessories that even the playing field. FX Maverick .25 sniper with Saber Tactical adjustable butt plate and cheek riser. Rifle came Friday, put a tin of FX 34’s through it yesterday to settle it in, today found a decent tune with the swirling 10-15mph tail winds in the rain. Splatter burst is (5) 5 shot groups at 50 yards, 8” gong is (3) 5 shot groups at 100 yards. FX 34’s going 895fps.