Like new condition in the box with the original manual, papers, test sheet and euro optics card.

Retails for $595 for the FFP version. Is on backorder and sometimes hard to find. In my opinion, one of the best compact scopes without going to the very high end category. This is American made, amazing quality, super lightweight and compact. Basically the same size as a Vector Veyron but much better quality. Very clear glass that doesn't have too thin of a reticle at lower magnification.

Here is a review of the other reticle version:
And a video of the FFP put to good use:

These work great on a small platform like the Leshiy Classic, L2, and the Lelya (which I have used it on all) or any rifle you want to keep the weight down on.


Normally retails for $595 but is usually on back order at most places.

SOLD

Here are some pics:






T

First question: I have two pumps and a compressor and several air tanks with gauges, and all gauges show different numbers from one another. It is impossible to know what the actual pressure is.
Does anyone know if pump/compressor hoses exist, that allow a 1/8 BSP thread pressure gauge to be installed on the hose itself somewhere? Or maybe an adaptor that sits between the hose and the pump, or between the hose and the air tank?
I have an electronic pressure gauge that I could install somewhere, and which I think might be most believable, but the most obvious place would be on the hose itself somewhere, which would make it reusable.

Second question: see this pump image -


Notice, how there is a red colored piece at the end of the hose. This is a filter for oil/water. Should the hose be installed with the filter towards the air tank, as it is on this picture? Shouldn't this end be connected to the pump? What about the bigger size pump filters, like this one:

Should this filter also be connected on the air tank side (to the quick attach probe)?

This FX Chrony V1 is like new condition. It comes with a velcro strap attached that lets you easily mount it to barrels, shrouds, etc to get a good reading. It has a bolt/washer setup that can screw into the bottom to fit on certain tripods. It does NOT come with the mounting bracket, but I should be able to provide you with a 3D printed one that functions exactly the same. However, it's not really needed due to the velcro system or tripod mounting.


It retails for $200 but I will take $160 shipped.

Like new condition, in original box. Edgun Dedal Stalker Scope 6x30. It's like the Russian version of the ACOG... they are not sold in the US anymore. It has no blemishes or issues, illumination works great, super fast target acquisition, and will be hard letting this one go. I might trade for a high end optic with higher magnification.

Official Dedal website (has the downloadable manual btw)

Only website that still lists a price is here for 900 euros

Here are the pictures!

Hey guys,

This is probably a stupid question but I wanted to know if there's anything wrong with using some rubbing (isopropyl) alcohol to clean the outside of an FX carbon fiber bottle. One of my M3 bottles had some decals on it and when I removed them, they left behind some sticky residue. Normally in these situations, a little rubbing alcohol will remove the residue with a little effort but I just wanted to know if the alcohol would potentially hurt the epoxy (or whatever it is) on the bottle. Filling these things up to 250+ bar, I don't want to mess with the integrity of the bottle so anyone know if it's ok to clean it this way?

If not, what's a better way of removing the residue without using alcohol?

Thanks in advance for the help!

Most ballistic apps have scope location settings for horizontal (X) offset and vertical (Y) offset. They can be set to actual inches of offset if needed. Though I don’t use those, what I would use, but what’s missing is a similar setting for (Z) offset. That would be how far away the scope is from the muzzle. Drop is measured from muzzle, while angular adjustment of the turrets is measured from the scope. When that distance is large, it makes a difference. I have a couple of long range airguns where that scope to muzzle distance exceeds a yard. There is no way for the ballistic app to correspond at all distances without taking (Z) into account, yet they don’t do it.

So I'm looking to buy an airgun that is single stroke (single pump) that is also muti-shot capable, like a repeater. Pump,shoot,pump,shoot
I'm trying to find one similar to that barra old west one or the daisy pump one, but something that shoots harder than those examples at 350fps? Oh and I'd like to spend under 200 if possible

I'm in Virginia. Whats an economical feed for refilling my squirrel feeder?

I've owned a few Chinese made pcps and still own a B&W S45 and consider it one of my best all around high power simi auto airgun.

I'm just curious if these airguns made in China are available to the people in China? For sure powder burners are not allowed.

Don't for sure want this simple post to turn into a political thread so ....I hope that the peasants around the world where fire arms are not allowed can own a PCP but it seems as though there are many manufacturers of air rifles that don't allow fire arms. Just saying.

DonnyFL SUMO Moderator .177/.22 1/2x20UNF. Like new, Not a mark on it. $120 shipped.

Hi , I’ve a question, how to get better
Results with the spreads ? Here are my chronographs results :

There is a new hunting opportunity for us living in the Pacific Northwest

I have an excellent condition Element Helix scope for sale. This scope is super nice. My only complaint is that my old eyes can’t take advantage of the amazing reticle that comes with this scope. I loose the ultra fine center dot easily. I find that thicker crosshairs just work better for me so the Element is going to someone at a great price. Everything that came in the box is present.

$260 and you pay for the shipping. I take PPFF unless you are willing to cover the fee on goods and services. Let me know if you have any questions.

I bought a .22cal RAW HM1000x about 6 months ago. Martin said it was tuned to shoot JSB 18gr at speeds around 970-980 fps. However, I found the rifle wasn't accurate as received. Also, I bought it with 2 barrels - a 20" and a 22".

Over the past 6 months, I've tried various Air Arms, H&N, JSB, Daystate and other pellets at energies between 30 - 45 foot pounds. I've tried different regulator settings, different hammer springs, and an SSG. I've shot from a bipod, from sandbags, and from a rest. The average accuracy is 1 - 2" groups at 25 yards. 50yd groups are all over the place. In no case could I get even close to 1/4" groups at 25 yards which would be my minimum standard. For reference, my .177cal RAW will shoot 1/8" groups at 25 yards with several different pellets and 1/2" groups at 50 yards. After giving up on pellets, I tried shooting slugs from ZAN, FX, and JSB at various speeds, but the accuracy was worse. I just received some NSA slugs tonight that I will try this weekend, but I'm not holding out a lot of hope

My conclusion is that both barrels are bad. I've been talking with Martin the whole time, trying different ideas that he had, but nothing has worked so far. He recently said that the .22cal barrels have not been very accurate the past few years, and that he has gotten a lot of them back. I'm likely going to be sending these back to him too, but I want to make sure Ive exhausted all of my options first.

Both bores are polished, and the crowns are very clean, even, and without any burrs. The only issue that i can find is that each bore is slightly tighter the first 1 - 2 inches (at the breach end) and then the pellet pushes through the bores without any resistance the rest of the way. They are both unchoked. I'm thinking the tighter breech may be what is ruining the accuracy. Is it worth trying to open this up by polishing it with a mild valve grinding compound?

Any ideas would be greatly appreciated.

Thanks!

Found a 303 Super at a recent gun show. The rear sight is missing , other than that its in great condition. I would like to find the rear sight, adds character. Any leads would be appreciated. Thanks

Well weather , wind I just dropped back to 50y from 100 .

17 clicks first 15 tries. Irons , cphp .177 ,R9 mhaa... I guess it will do for today or old age showing up more each year..

First 11 after 17 -- last 5 by put
clicks. --- -- --- ------ Up time

My little backyard setup. Highly residential area so discretion is necessary. As u can c I have a Crimson trace CMR-206 Rail Master sight on this so I can literally "shoot from the hip" and be deadly accurate. This is the 1st $1,000 pellet gun I've ever had and before I even shot it I ripped it apart to switch cockin fron a right handed to a lect handed mechenism. Doing this is not for the "faint-hearted". It's actually quite hard to do. Example: I had everything apart but the assembly still wouldn't come out. But if I jiggle it just right the entire "guts" literally slude right out. It seems it's one of those "push down and slide out" tupe of mechanizm. it's a German/computer made object so everything fits exact. DO DON'T FORCE ANYTHING" anyway, I'm so glad I made it a "Lefthanded" cocking mechanizm. It is now "apart of me" and we work together for the perfect shot. I mean with a CMR-206 Rail Master laser I am in complete control of this Pistol. The CMR-206 is non forgivi

Pros
Once I switched to a "Lefty" cocking mechanizm it was nothing but shear pleasure

Cons
$1000.hey buy I jumped from a $180 Diana Bandit to this. And Im sure glad I did. I never knew plinking could be soo much fun. I mean I get 25 shots between fills. (The Diana Bandit 9 shots) dont get me wrong, I love the simplicity of the bandit. I just never knew that plinking could be as great as with the HW 44. Its quiet as u can get. It loads very easy. I cant say enough about this pistol. The only thing iD change would be is to make the safty quiet. Its so loud it chases the game away. Literally. Once the squirrels here the click of the saftey they are gone. Bummer.

You can probably find one of these at your local hardware store.
In the future I'll just toss one in each package.

I've fired just over 600 rounds in my Avenge X with no issues and now today a I've got a major 3 car pellet disaster inside my barrel. Not sure how this happened and what caused it but I was firing at a target and noticed no hit on it or around. Thought I must have just missed and so I fired again, same thing but accompanied with a slightly different sound than I normally hear. I fire one more time into the ground in front of me and FINALLY it dawns on me that nothing is coming out and I have now fired two pellets into the first that never exited the barrel. As I point the weapon up and down I can hear loose pieces that I can only hope and assume are from the pellets.

My question now is what is the best way to try and clear this and ideas what caused it....defective or pinched pellet upon entering the chamber? Have I now done damage to my barrel?

Has anyone used shelterdist.com? ScamAdviser says its OK but it seems to good to be true. Anyone had any experience with them?

Looking to sell a nice FX Dream Tact in .177 cal. Had big plans for it but gone in another direction. Only shot it to verify function. It's currently shooting FX 10.3 at 825 fps. Comes with various different weight hammers to dial in whatever velocity you want. Has a brand new barrel kit with a used Donnyfl Tanto which someone drilled holes in. Very quiet.
The target shown is a full mag leaning in a doorway at 25 yds. The shot that dropped low was 100% me.
Comes with 2 mags, various hammers, an o-ring kit, and a plenum which I got with the gun. Not sure of it's value. Also comes with the Mueller 8.5-25 scope and mounts.
Asking $625 shipped TYD in the lower 48.

As new STIKMAN SCBA fill staion, Cascade fill feature. 48″ Microbore hose with female Foster quick connect fitting.
Has everything it came with new. Used As a back up for my Din 300 omega tanks. 150.00 shipped
Only trades im interested in are 257 caliber ammo and or molds for casting. My feedback is A ok......

Be a better field target shooter in 15 minutes- Pellet Sorting with Greg Sauve
In this episode, I talk to Greg Sauve about what he does to prepare for a match regarding inspecting and sorting pellets. It's a tedious process but can make a huge difference for those shooters looking for every point!

#airgunshooting #getoutandshoot #fieldtarget #airgunfieldtarget #aafta #deadeyenc #pelletsorting

.

For those who have ordered CARM magazines from Croatia, how long have your shipping times been? Ordered on 11/24, processed and sent on 11/27 (information from Croatia Post) When I check USPS tracking, it states "Origin Post is Preparing Shipment".
Obviously, I expect longer shipping time from Europe (although Krale manages it in 2-3 days - incredible!), but just curious how long it has taken others to receive theirs.
Not griping, just curious.