Hello fellow airgunners,

Finally some sunshine on my target. Soon also on the bench again.

Love to share this video & short with you guys.





Keep on shooting!

Hi, new member here. Just put some pic my two 10m 80's rifles. Both are refurbished with new seals and springs. and perfect condition.

Diana 75 hv and Anschutz lg 380 match.

My new Crosman 3622 came in today. Installed a steel breech kit I had squirreled away for a rainy day. Rifle looks excellent. Bluing is deep and shiny. Barrel is spotless and the crown looks great. Rifling is sharp and neat. I ran a patch which came out nearly clean. The 3622 weighs 3.8 pounds bare on my scale. I cannot over emphasize how sleek and tiny this rifle is. Compared to a Benjamin pump 392, the Benji is huge, hulking, heavy. The stock feels great and is made in two pieces. The forward section replaces the pump arm on the 362 and attaches via the two plastic barrel bands. The length of pull is adult, small to medium adult , and is about .5 inches shorter than a Marauder.

Here is my almost not a Marauder .25 Super Light (5.3 pounds bare) compared to the new 3622:



I was able to get a BSA 2-7X33 compact scope intended for the Ruger 1022 mounted up and get a few shots in. Velocity was right on the stated 700 fps for 24+ shots. I sighted in at 15 yards due to the cold and wind and the rifle made a tight, slightly ragged hole using the CPHP pellets. Noise, I would say it is relatively quite, moderate report. Slightly sharp pop. The Marauder is noticeably quieter, but I am running an added DFLS on the carbine length short shroud.

I am going to give this 3622 a full 10 stars. The only let down is the trigger, so maybe 9 for 10. The trigger is not really bad and I am sure I can work it a bit. A little heavy but predictable. What I do not like is that the trigger is plastic. The trigger is the most important tactile contact point and I would wish it to be metal, like the Marauder and like the GTA trigger I installed to replace the plastic trigger on my Urban.

I read so little about the whole FX airguns lawsuit / whatever it is, really no idea what exactly is going on with wall that. but im looking to get an FX airgun with my tax returns, should I be concerned? or does this have nothing to do with that at all? any help would be greatly appreciated as I have little to no idea what's going on with all that

it just snapped when cocking it,poor grain direction .I did my repair and decided to modify the crappy pressed checkering. I hadn't stippled in 10 plus years so its not my best ,but I really didn't care for the original. I still have to finish the stock ,the stippling was a test.

Those of you that have owned a Dreamline and a Crown Mk 2 at the same time know that you can use your Dreamline barrels in your Crown - they just look a little “skinny” in the Crown.

Bullet Central sells a Carbon Fiber shroud in 500, 600 and 700mm lengths.

This shroud lets you slide your Dreamline barrel inside it. The BC carbon shroud is threaded 1/2 UNF internally, so you screw your Dreamline shroud into the muzzle end of the BC carbon fiber shroud using the Dreamline barrel’s moderator threads.

BC shroud is Super simple, super solid, weighs nothing and looks pretty.

Since I have 3 Dreamline 600mm barrels (.22, .25 and .30), I can use the same BC Carbon Fiber shroud with all three barrels screwing off one barrel and onto another Takes less than 60 seconds.

The BC shroud is not cheap at $115, and its just cosmetic… but I thought it was pretty enough that I splurged. I’m normally a function over form type of guy, but heck my Crown shot a 200 at the 40 Yard Challenge, so she deserves a little dress up, lol.

-Ed

Hawke Airmax 4-16 x 50 in excellent condition. Check the pictures to see the scope’s condition and what’s included. $ 250 which includes insured shipping. I accept a money order or a check with a hold for clearance. U.S. sales, only.

I have had my 2240 for years, and every now and then I tinker with set up changing various things looking to improve performance etc. This time I used a "safepac" style pcp conversion, and did some work on the valve port for improved flow. All things have gone fairly well, but now I need to get a stronger hammer spring. At a full air charge the chrony numbers start low as the current spring does not hit hard enough to release enough air against max pressure. After about 5 shots the numbers climb, the accuracy dials in, and then goes back the other way once the overall pressure in the reservoir drops. I see there are hammer spring kits with as many as 4 different wire guages. If any of you have been down this road, what spring did you settle as the ideal set up for complete release at full pressure? Thanks in advance

MTC Genesis LR 5X20X50; Butler Creek flip up caps, fully functional, no issues, sat on my LGV for years. $200 + shipping USPS money order only.

I'm the original owner of this Brocock (BRK) Ghost HP 22 cal. It was purchased at AoA in late 2022.

The trigger has been adjusted to make it much lighter than stock. Otherwise, the rifle is all original.

Price is $1,795 plus shipping or it is available for pickup at Rio Salado Range (AZ).

Thank you but no trades.

I have a new R9, looking for advice about scope and rings. I target and plinking at 50yds max. I’m not a hunter, but these iguanas are fun and saving the environment at the same time. South Florida has a real problem good targets.

..maybe im just morbid.

Having a bit of an issue with my Avenge-x (.22 with carbon fiber bottle) I'm hoping that maybe someone here knows what is going on.

I was shooting some a few days ago and I was getting a little below 890fps. I tried shooting again today (without touching any settings and with the same ammo) and I'm getting 860fps. Normally I would chalk this up to differences in weather, but that seems like quite a drastic change in fps.
The gauges seem to be reading all correctly, so I'm thinking it might be the hammer spring is starting to wear. I wanted you guy's opinion before getting a replacement, although I might get one anyways they don't seem that expensive.

My settings are:
2500psi on reg
+7.5 turns on the HS
TP set to High
Shooting JTS Domed (25.39gr)

I’ve had to ask the forum quite a few questions to get to this stage and I thank all those that took the time to give me advice. I don’t know anyone with an air rifle so I’m very indebted to this group of guys and forum. My setup is the HW30S with a HAWKE 2-7x32 Vantage AO. I have cheap Target Match single screw mounts med height, not even a recoil pin (that‘s all I could find and it will do for now until my store gets a nice one piece in). Pellets today were H&N Field Target Trophy 4.5mm 8.64 grn. My gun, out of the box, zeroed at 20 yards. It took about 20 shots to zero (forgot to adjust the parallax in my first 3 shots). This is my last 2 - 5 shot groups. Both can be covered with a dime and my last on the right, 3 pellets through the same hole. I’m an old geezer that had lense replacement surgery for cataracts 3 months ago. Powder burner for 50 years. This is going to be much fun! Better late than never! Beyond my expectation results. What distances do other .177 HW30/R7 normally shoot for targets?

AEA or Bin Tac:

Three scopes for sale!

Element Titan 3-18 x 50 FFP $475 shipped

Hawke Airmax 4-16 x 50 SFP $300 shipped
With sunshade and box

View attachment 442580

I don't have enough room to dedicate space to pellet storage and am always moving tins out of the way or working around them, so I made this little two-sided storage/organizer. I can see what I've got, easily select a tin or push the whole lot aside. Glued and screwed, it's plenty strong even if not "furniture grade" fit and finish, lol. The bare wood slides on my carpeted work area. If it were a hard work surface I'd use carpet tape and secure a piece of carpet to the underside or put little casters on it.

Can someone make me a meme of a homeless guy holding a sign, that says "will do tile work for Huben GK1"

Thank you in advance

Just the way I like it!



•Airgun: FX Airguns Panthera
•Rail: Kraford Lypt PR5
•Weights: Kraford Lypt Fat Bastard
•Bipod: Scandinavian Arms
•Grip: ERGOAir vertical
•Magazine: Studmagloader
•Tank: AirMarksman
•Moderator: Impulse Airgun
•Scope: Nightforce Optics NX-8
•Rings: Sportsmatch UK Ltd.

99% condition. One very small imperfection, but otherwise perfect. Santa Rosa address. Five shot chrony string with 13.58gr. Beeman Kodiak pellets: 698, 694, 694, 689, 692. Average FPS: 693.4. Standard Deviation: 3FPS. Energy: 14.5FPE. Spec for this gun is 15.1FPE. Blue book value is $690 used. Ship weight: 10lbs, 11ozs. Dimensions: 50" x 10" x 5.5". Buyer pays actual UPS ground insured (Pirate Ship). Paypal FF/Venmo/Walmart2Walmart or PP G&S (+3.3%). Asking $550 + shipping.

I have two UTG compact scopes for sale. One is a 3-12 X 44 the other is a 4-16X44. They are both the smaller compact versions with illuminated reticles. Both are like new shape. Both include flip scope caps and UTG rings. I have the original box for the 4-16 but not the 3-12. The scope without rings attached in the pics is the 4-16. The one with the rings is the 3-12. Looking for 80 shipped a piece or 145 for both.

Sold to Mr. J.P. 2 Apr 24

USFT MAC1 #134

.177 WFTF <12 FT LBS

REGULATED

TUBE VERSION

$1950.00 PLUS $75. INSURED AND SIGNATURE REQUIRED SHIPPING

YES - HARD TO FIND AND SELDOM COME UP FOR SALE.

Regulator = Yup. There's a guns inside the tube that you access after you empty the gun and take off the access plug where the foster fitting is screwed into. Then use the long rod with flat tip screw driver to turn up or down.

I JUST ACQUIRED THE <20 FTLB HFT USFT MAC1 BOTTLE VERSION SO I'M SELLING THIS ONE.

I WILL INCLUDE THE ROWAN THREADED 1/2" UNF ADAPTER for moderating - VERY QUIET WITH a moderator.

I HAVE LOTS OF POSITIVE FEEDBACK SO BUY WITH CONFIDENCE

TEXT FOR FASTEST RESPONSE - RUDY SMITH AT 251-610-8582
PAYPAL: [email protected]
VENMO: RUDY-SMITH-15
ZELLE: 251-610-8582

Hi lads, seeing how NOBODY has downloaded my gk1 perfected mod:


Despite being awesome and ultra-affordable, I came to the conclusion that.. maybe not manny people have both a GK1 V1 and a 3d printer to begin with... so... maybe I need to focus on doing something for a more worldwide spread airgun.

The initial guns that come to mind are the 2240 and the diana chaser, how many of you have one of those? Do you know about a even more popular air pistol?
I know the 2240 is more owned, but I also think that maybe the chaser is prefered for younger shooters that also are more into 3d printing.


The design of my "cheapo" (3d printed, 23cm long, single or double action, 12 shoot pcp pistol) is completed for almost 2 months, but I think that will occur the same that happened with de GK1 perfected mod, I have to count on people willing to purchase an e-bay pcp conversor for the 2240, + a cheap gamo barrel that aparently is not available on the states... So... Nobody is gonna download it.


With a bit of work, I could adapt the ideas and design to make the same but using the 2240 or the chaser has the base, you will have a 3d mod that turns the gun into a double (with really long and hard trigger) action or single action (short and nice pre-loaded pull) 12 shot revolver. Thar may sell much better, no need for extra equipment, e-bay chinesse parts or crappy barrels not available in most countries.

Would you pay 10 bucks to turn your 2240 or chaser into such revolver?

What features do you like it to have?

Are you aware of an equally popular airgun that everyone has?

We are happy to say that we can finally offer you the option of extreme long shooting with the right tool.

.22 caliber slug will weigh 35 grains and a .25 caliber slug will weigh 44 grains.
The box will contain 200 pieces at a very reasonable price.

These should be in production in a month.