Hi Guys,

I have decided to make some room in my safe and have put up my RAW .30 cal up for sale.
This is a package deal with everything on the table.
5 magazines, 2 moderator lengths, 2 stocks, 1 1/4 tins of 44.75 pellets, and Anschutz Pickatinny adapter.

For everything in these pictures I am looking for $1600 + shipping

So now for the details
This is a RAW LRT made by Martin, notice the wood trigger guard.
Personally I find this more desirable than the metal trigger guard.
I was contemplating doing a fresh refinish on the stock as it has become almost a green laminate now.
And thought as many guys like the green I would leave it.
I recently had it completely resealed and in the process my tuner and I had a discussion and he convinced me that it would
be good to go with a new HUMA regulator.

Also included is the Sporter stock I refinished years ago.
I changed the trigger guard to match the LRT stocks, and decided to try and stain it.
It was a lot of effort, but it came out good.

Next up the Moderator,
The stock moderator is 2 chambers, and can be a bit loud with a .30 cal.
So I called Martin up and asked "by chance would you sell me extra chambers?"
He replied no problem how many do you want?
I bought 3 and it is amazing the difference, it takes a 30 cal RAW and makes it backyard friendly.
I then found the exact twill Carbon Fiber tubing that RAW uses and bought several feet.
It also makes it extremely long so that is where having the stock length moderator is still good.
You currently have 2 lengths, but there is a spare piece of the tubing that could make a 3 length of 3 chambers.
I never did this because I liked the 5 chamber design so much.

Magazines,
I like to read so I have always bought many magazines. Oh wait wrong type of magazine. hahaha.
I have a total of 5 magazines and if you have ever bought RAW magazines you know this is not cheap.
I have 4 right side magazines and 1 left. I bought the left as I was experimenting with a scope that had clearance issues at the time.

Anschutz adapter,
This will allow you to use pickatinny for a bipod, which I imagine most of you will go for.

Stock Regulator will be included as well.

If you do the numbers you will see this is a smoking deal as this package would be very expensive to replicate.

Let me know if you have any questions.

Greetings my fellow air gunners, just wanna say thank you to all that help me getting my account restored....Simplyhooked PCPs you are greatly appreciated. Big Thanks....

I have never been to a FT event. Do people still use high end traditional air guns anymore? Is it all PCP?

What's the best looking air rifle you've seen or shot. That 1 air rifle that you'll never sell and would keep.

Talon Tunes 580cc bottle for Impact Mk1 and 2. Will fit Mk3 if reg is deleted or you update bottle valve. Excellent condition. Lots of life left. Ships empty.




$160 shipped

Saber Tactical Adj butt stock-Excellent condition-SOLD



$125 shipped-SOLD

600mm .25 STX Superior barrel kit with FX carbon fiber liner and .25 probe. Blemish on shroud but only cosmetic. Screw on thread protector ready for your moderator.





$200 shipped-SOLD

Any questions please let me know. PP FF preferred. Longtime member.

Thanks!

DT

FX WILDCAT .22 CALIBER WITH 4 MAGS AND ALSO SOME NEW SPARE PARTS , HAS FX MODERATOR , with all kinds of spare fx parts , new valve , hammer cocking mechanism trigger sear ect, ACCURATE GREAT LITTLE BULLPUP
PRICE $750 SHIPPED PAYPAL F&F W/O SCOPE
here is some NEW parts I will give with gun so if anything fails you own it

hello everyone. so the airgun geeks YouTube channel just posted a new video on the new umarex Zelos (). a lot of us know that is is simply just the snowpeak m60 with the umarex name on it, but at $599 are we thinking that's reasonable? to my knowledge its a bit tricky to get an m60 in the US and when you can Im thinking its around that same price anyway. I think I like how the gun looks, and overall I think the gun could be really really cool, but is it worth the $600? personally I think it is...but I want to hear what you guys think, let me know!

Got a new toy toy in the mail today! I'd wanted an Eliminator in .20 ever since watching Kevin shoot his .25 on the Pellets and Pistons YouTube channel. After a member here graciously offered to let his go I couldn't get my wallet out fast enough.



I opened the box and the seller had gone above and beyond and shipped it in a protective hard case. When I opened it I was definitely taken back for a moment. He had sent plenty of pictures but they didn't do this thing justice. It is beautiful in person!

Well as soon as I was done cleaning the drool off of myself and the floor I took it over to the shooting bench. I went to cock it and the barrel cracked open just a hair. I pulled hard and nothing. Pulled harder with both hands and FINALLY it cocked back. Loaded up a pellet and shot it. It was loud lol. Definitely not an HW30S. I pulled the valve plug on the back and released a couple spurts or air. Cocked it again (still a beast but manageable for my little arms) and shot one over the chrono.



NEARLY 29FTLBS! Thats awesome but I don't need all of that. I proceeded to release air and chrono it until cocking it was more manageable but still put out some impressive numbers. I ended up right at ~24fpe. Still not an all day shooter but at least I can cock it easily enough now. I'll probably end up bringing it down to Hunter Class power levels around 19.5fpe. That will be easy on the arms and still a pretty decent laser.



Here are my first 30m groups with the Crow Mag shooting the JSB 13.4gr pellets. Grouping pretty well for a "new" gun IMO

I done a side lever mod today. It works great and cost less than 10 bucks. It can go back to stock if I wanted it to. The only thing that I can't put back is the little notch I cut out of the stock for the handle to set in. I put 60 pellets through it and I really like it.

I guess the guys across the pond are getting there shipments early......

My GK1 (v1#67) just finished its 66th 150ct tin of .22 GTOs. That’s 9900 of em, costing in total more than I paid for the GK1. Since I’ve also shot at least 100 other projectiles (being conservative here), I’m calling this it’s 10000-shot celebration.

In that time, it has actually just got better, or perhaps that’s me getting better at shooting it, or both. It consistently shoots 1/2” (or less) groups at 50 yards with GTOs at 900fps and has never failed to shoot, jammed, or had any other issue. All original parts including the gate, which works very well with no seating needed for GTOs - just clicking 2 in at a time. It just gets filled and shot and shot and shot and shot, 250bar to 190 and the mag and air (nitrogen in my case) are reloaded. The barrel gets cleaned every 3 tins from the front with a rod and retractable patches - 5min job. I use it mostly for fun (spinners and targets), pesting (99% rats) and it goes hiking and Xcountry skiing in my pack. It has sported red dots, prisms, a $3k thermal and currently is fitted with a bugbuster, which I use to shoot precisely from a rice bag with short eye relief at 10X or using a freehand taco hold at 3X, which allows quite a bit of eye relief. It spent most of its life with an Impulse Air 1200 mod, then I made the shroud active, and now it is wearing @subscriber ‘s oval mod, which makes it sound like tapping a nail.



Here is my celebratory 50y, 5 shot group. I pushed out the boat and used a splatter target, which I then peeled off to show how good this thing really is. It does this all day every day, in semi auto, with a sublime trigger that tapped two into a raccoon dome 1/4 inch and 1/4 second apart.





Because there is no reg (to creep), the icing on the cake is that it will hit your point of aim every time you pick it up. It’s the perfect pesting instrument. Quiet, handy and absolutely clinical.

Ill end with a great quote from our friend Manny (@Nomadic Pirate 66) who posted this very early in the main Huben GK1 thread, before release:

“I've been searching for a PCP pistol that fits my needs for over a decade and a half now,...the Huben might well be nirvana.”

Manny seems to have a pretty good crystal ball, but did he envision that V1 issue #67 would make it to 10k shots without a single hiccup? I think that’s pretty remarkable for a semi…

I was wanting to know what the maximum velocity that a fx king can get with a 18.13 pellet. Thank you. And when can I get one in brown?

The classic Leshiy is small, lightweight, and virtually indestructible. This has a custom hammer spring with a PEEK preload bushing that gives it a huge range in power and efficiency. Huma regulated. I have (3) Leshiy's already, so this one can go.

Included:

• Original Leshiy (very few marks)
• 350mm LW 9mm/.357 barrel
• 250mm LW .22 barrel
• Factory baffle with a custom marine brass bore reducer (.22)
• DonnyFL 1/2-20 moderator adapter kit
• RARE auxiliary air cylinder made by John Hagan (I think it's 1 of 5 total made)
• Shroud extender
• DonnyFL Baffle inset
• Spare valve
• Custom hammer spring and PEEK preload bushing
• Upgraded Wiki manometer / air cylinder gauge (300bar)

Terms:

• No trades. Not offering any of the accessories until the Leshiy has sold
• $1425 shipped for everything
• $1100 for Leshiy + 350mm 9mm barrel, DonnyFL 1/2-20 adapter + 1/2 shipping
• $950 for Leshiy + 250mm, Huma regulator, and spare valve + 1/2 shipping

I bought one of these over a year ago, and recently was planning on installing it in my Impact.
I cleaned the liner, and looking at it I can see the pressed in grooves on the outside, but looking inside the liner it appears to be smooth bore with just a hint of rifling. Definitely nothing like all the other FX liners I’ve looked at.

Has anyone else ran in to this issue? I know this Superior Slug was made after the Superior Heavy and before the Slug.
I’m guessing it won’t shoot very well.

Since FX never publicly admits their mistakes, is this something that happened and was brushed under the rug?

AirMaks arms padded gun case in great condition.
32 inches by 11 inches
$50 Shipped TYD

So I received my CS4 on 19 Feb 2024. Took the case apart to install an hour meter (which didn't work like I wanted it to, so ordered a different one).

Removed the small pre-filter and installed my homemade one with color-changing silica beads in it. (Two 3/4" PVC caps, tube wrapped with electrical tape to make a snug fit. Intake end has holes drilled in it, output end has a 3/8" brass pipe fitting to mate with the brass elbow into the compressor head).


Had some rusty water inside the bag when it arrived. No large debris in the water tank, but I flushed it about five times with tap water until it ran clear (was a little murky at first). Then put some Dawn dish soap in the reservoir and ran it for a couple of minutes, then began flushing it. After several fill/run/flush cycles, it was running clear. Then I purged the system completely of water, and finished by filling it with 250 ml of distilled water.

Connected some LED strips to the coolant hoses to make the water flow easy to see when running. Soldered them to the pump contacts so that they come on when the power switch is switched on.



Also added a 4-sensor temperature logger, but one sensor (to the motor) is faulty. Waiting on the seller to get back to me on a replacement. Have the sensors on the Head, Coolant tank, Motor, and Ambient air for tracking purposes. (Temps are - MHCA - Motor, Head of cylinder, Coolant tank, Ambient)

(Start of the 2-hour break-in run)



(Temps after 30 minutes)


Currently running the compressor for two hours with no load, though I saw nothing about that in the owner's manual, only saw it here on AGN. Where did this info come from?





Parts:
Hour meter #1: (returned because it is too large and the backlight won't come on when the power switch is turned on) - https://www.amazon.com/gp/product/B0C539D7R8

Replaced with this one. Smaller footprint, allowed me to install it in the back of the lower case, as opposed to the top cover, which would require disconnecting wires every time I opened the case:
Hour meter #2: https://www.amazon.com/dp/B0C2XZ3SYV

Plastic tube for pre-filter: https://www.amazon.com/dp/B08ZM5BCQJ

Silica for pre-filter: https://www.amazon.com/dp/B09QFJQQ7Q

Big air filter: https://www.amazon.com/dp/B0BBM4BB84

Small air filter: https://www.amazon.com/dp/B07M8KTS9B

Temperature logger: https://www.amazon.com/dp/B0C39TKV4X

LED strips: https://www.amazon.com/dp/B014V4RO2W

So I've been dabbling in NRL22 lately and I have had another one of my dumb ideas. In NRL22, they have a monthly course of fire that all of the clubs shoot, and each club usually adds some extra stages as well. In each months course of fire, they include instructions for Adaptive Class for shooters that are not as mobile as they used to be. For example, a stage might have you shooting back and forth from a tripod and prone. For Adaptive class, you would use a 55 gallon drum instead of going prone.
A club where I have been shooting NRL22 takes this a step further and lets shooter shoot the course of fire from benches. No moving, just sitting at the bench shooting the targets.

So my brilliant idea was to add an un-official FT class. Shooters could shoot the course of fire off of a seat with sticks, just like long range FT. And any stage with a lot of standing could be shot standing off of sticks.

It would be more challenging than long range FT because the NRL22 targets are generally smaller (range is 40 to 100 yards, target sizes are 1/4" to 3") and you have to shoot 10-12 rounds in 2 minutes (oops, we just lost Ron), but it might be a good way to get more use from your long range air guns. And the NRL22 rules allow slugs up to .25 caliber, pellets only at .30 caliber.

Is this something you, as a long range FT shooter, would be interested in trying? Assuming a match was fairly close and price was $20 or less? Throw a reply down here to let me know what you think. Especially if you are local to me, as this may go from theoretical to practical in the next couple of months. If you aren't sure if you are local to me, you aren't. Trust me, the people that are local to me know it all too well.

Well , it seems that my M3 with its current setup/config is finally behaving itself.

Over the past few weeks i have taken it out to fire a group every few days .... to see how it does , and It has been doing very well!!

Routine is full 250bar charge ... ( i dont fire under 200bar so approx. 30 shots before recharge ) ...... 5 shots to settle...then a 10 shot group at 120yds . I pick a day time when the wind is basically zero.

Setup..
NSA 27.5 at 1060fps
1st Reg 200bar
2nd Reg 145bar

Tungsten Hammer
Pin Probe.

Custom Carbon Fibre ( 4dia tube sections with machined spacers pressed and bonded)
FX barrel liner and original tube fully bonded with Carbon tube sections.

The whole barrel/liner assembly has NO tension on it whatsoever.....

Results form this arvo..... which are typical of what it has been doing..

I am seeing to measure scope height after zero as well as velocity at a couple different distances. If I get sighted in at 35 yards then I need to get scope height? Or is it measure my scope height before and input it into the ballistic app? I’m just not understanding getting a scope height after I zero?

Also, if I run a magneto speed and only able to get a velocity at the muzzle how would you get the velocity at say 50 and 75 yards to input that information in the app?

Thanks.

If I shoot to targets at 50 or 88 yards, my Sidewinder .25 if not as accurate as my FX Panthera.... Or at least I can control the better the Panthera.

If I go out and shoot at long distance, the Sidewinder is extremely accurate. I just took two birds at 150 yards, easily.

So, the problem when shooting to paper targets is not a lack of accuracy, it should be something I am doing in a wrong way..... But I have not identify that yet.

Well, I'm pretty much a walnut stock snob, kinda guy. I love them, but I'm always disappointed when the factory applies dark stain over walnut, seemingly to make the color more uniform. Maybe it's done so that no one complains about "their stock" looking different from the pics on the website.
Natural walnut does have wide variations of color and grain, (just look at both sides of my stock). Idk, but it often covers up some nice multi-shade mineral lines underneath.
So, when I received my new K1 a few weeks ago, I new right away that I would once again have to refinish, in order for ME, (snob part), to appreciate the natural wood.
So, I sanded off all the stain & pressed checkering, added some decorative caps to the grip and forearm, made from Gaboon Ebony wood, and Basswood spacer, and then applied several coats of Maccari Royal London Oil.
His oil leaves a very light honey color, seals a bit and protects the wood, and gives a nice satin rich look to MY eye, similar to many European gun stocks.
Then I had my checkering friend add some nice hand cut checkering.
The Huben comes with a combo of some pressed checkering and stippling that looks pretty nice, but it's quite smooth and not very functional imo.
Oh, and I added a rear sling QD stud, and a forearm recessed QD cup, for sling carry on my plinking woods walks.

Anyway, I'm much happier with the look, and feel, and wanted to share it with the Huben lovers on AGN.
But, I understand this is just my personal preference, and many like the darker look too.
These K1's & GK1's, are such amazing shooting machines!

Have fun!

Have joined this forum hoping to find assistance with finding a 2nd gen Umarex Walther PPK/S .177 cal BB gun. Am starting a bb hand gun collection (see "about me" in profile if you like) but the PPK is proving to be a hard find.

Am a huge history buff so begin collection with both Springfield armory and Colt versions of the 1911 and will soon adding a luger. They're not hard finds but, Wow, the PPK certainly is.

They are available from European vendors, am in process of finding out if they can deliver here to the U.S. Does anyone know?

Grew up in the era of James Bond, Cpt James T Kirk and Jim Phelps ( the original leader of the Impossible Mission force, still can't believe they made him the traitor in the 1st MI move, loved the rest of the MI movies but won't watch that one) and my name is James, so you can imagine who I often was playing games as a kid and why I want a PPK.

Also would like a Colt Hammerless 1903/1908, seen in the old MI TV series, but doesn't appear a replica BB or pellet gun is made. Anyone know if one is?

Thanks everyone

Monstrum 4x12 - 44 AO rifle scope. New in box. Reduced - $75~

This is a great value with crisp optics at a bargain price. 1 inch diameter tube, 44 mm objective with 4–12 MIL Hash gradients. Nitrogen filled and is both fog and water resistant. Ideal for both air guns, and cartridge rifles. The aircraft grade 6061 aluminum construction and adjustable objective allows precise focusing.

The fit, finish and function are outstanding for the price. Includes flip up caps.

It is new and was never mounted.


In addition to the Monstrum scope, I am also selling a four pack of GAMO pellets and a 4500 PSI PCP compressor. Also need to sell a Diana Stormrider Gen 2 PCP, a Benjamin Cayden PCP. All of it new in box. Had to sell my place on acreage and move into town. I never got the chance to enjoy any of it.

New matte finish CF moderator. 177-25 caliber. Monocore design. 1/2-20 threads. 5.5" L x 1" diameter.

$40 shipped CONUS only
PayPal F&F or CASHAPP

FX Dreamlite .25 600mm

Second owner
Does not leak
O-rings replaced in AMP reg around 2021
Fx Power plenum
Comes with factory 250cc air tube (white gauge) and a lighter weight 220cc air tube (black gauge, installed)
Huma internal plenum, I never used it, came with 220cc tube
Huma Regulator gauge with better resolution
3 smaller Streamline mags, better with low scope rings
1 factory Dreamline mag
Homemade butt stock, better with low scope rings and Streamline mags
Factory butt stock
Fill probe
Huma 40/4 mod
Nearly full tin of 33.95 JSB
Misc 25g JSB, 20g H&N, Polymags
Factory box

I can remove the rubber grip gun tape, peels right off but makes picking up the gun much easier without a stock. If you are interested and don't want the grip tape. I can remove tape and send pics without it on.

Transfer port has been ported and pellet probe trimmed for better flow.
With 33.95 JSB's, hammer on "max" 939, 945, 944, 946 fps, app. 66 FPE
33.95 JSB ,hammer set at "B" 892, 888 fps for accuracy. It will shoot 25g too at lower hammer settings but I just stick with the heavies. It is FX accurate even at the higher FPS.
It will shoot the 20g H&N (included) at around 20 FPE if port and hammer turned to minimum to save air. These aren't JSB accurate but still fun to plink without using much air.

Only selling as I bought an FX Maverick

$800 shipped and double boxed with Huma. Or -$90 without the Huma mod, $710shipped