Air Gun Technologies Vulcan in Excellent condition. Holds air and shoots great. Comes with 3 mag's, fill probe and soft case. $625 + Plus shipping thru PayPal goods and services.

Went out this morning. Cold. Windy. what's new....
Got setup, started slinging lead
My coffee finally started waking me up about an hour in.
The wind is gusty as can be
I cant even hit the dang paper!
.... and I realize...I'd been turning my turrets the opposite of where there needed
Yay for dyslexia
Got them back to where about they "should be"....
I hear a vehicle...
No biggie...
I wait for them to pass(public shooting area)
..

...
Dude parks downrange of me
...
Gets out, picks up a rock and moves it out of the way for him to continue the path...
that rock is an indicator that the sand starts there.
He gets back in his truck.
He sits there....
For an hour...
Said screw it and packed up.
Was getting in to leave....
He starts to drive off INTO the direction of the sand....
I wait...

He makes it 30 yards and I see his truck slump in
Followed by multiple engine revs....
Definitely time to leave now
In the rearview I see him digging at the sand...
Sorry bud....shouldn't have interrupted me having a good time
My manners indicate that I won't bother interrupting you, because you seem to be having such a good time.

*those.gamo pellets are tttrrraaassshhhh.....but I got them to hit

March compact 2.5-25x42 with MTR-5 reticle. It’s in excellent condition. Includes everything shown along with a sunshade.Scope was purchased new in January 2023
Not interested in any trades
$1400 includes shipping to Conus,PayPal F&F excepted or add 3.5%
I purchased two March scopes and decided to sell this higher magnification scope and keep the 15x scope.
Steve

I'm working on tuning my wife's Bandit carbine without a regulator. I currently have it to where the bell curve is over the pressure range that I want, but the max velocity is a bit higher than I want. The bell curve is also sharper than I'm wanting, though I understand there are limitations with such a small air tube. It's doing 20 shots in an 8% spread, with a peak power of a bit over 12 fpe. I'd like to flatten that to a string of 24 shots with a peak of 10-11 fpe, so I'm thinking a smaller transfer port is the correct next step. Has anyone used 5 minute epoxy to fill a transfer port for drilling out? Or do I need to use some sort of JB weld metal putty? The transfer port is brass and is .146" in diameter.

Any advice would be appreciated.

The most sought after Theoben airgun. According to the Airgun Blue Book, 104 were produced. One cock 24FPE; two cocks 36FPE. This one is new and Beeman stamped. Purchased from Straight Shooters in 2001, then placed deep in a safe. I've never cocked it once. Even the rubber bands that held the inspection tags became brittle and fell off when I took photos. The only fingerprints on this gun since 2001 are mine. It looks like very small stamped "S" near the bottom of the stock in one of the photos, but that's how it was shipped to me. No trades, third party, or international sales. Will ship double boxed, UPS ground insured CONUS. Weight: 13lbs. Dimensions: 51" x 5" x 11". Buyer pays actual shipping charges. Paypal FF or Good and Services + 3.3%. Asking $4500 + shipping.

I cerakoted this in Burnt Bronze to match my bronze FX Impact. Not needed anymore so its up for grabs. Give me a fair price and i will ship to your door.

I think I paid around $45 for it.

My #1 shootin buddy is my dog Blanco. Smart as heck and not afraid of airguns or PB.
Rescued him from the streets of Mexico where he lived for two years.

Tore my shoulder up last October and the MRI didn’t look good. So had surgery first week of December and it ended being a tear in my bicep tendon, tear in my labrum and a spot on the rotator cuff that needed cleaned up. Today was the first time I’ve shot a springer since sometime in October and man did it feel good. Got my R7 out and shot this at 13yds. I definitely am going to put the scope back on it because shooting irons there’s too many fuzzy things lol.

R7
Falcon 7.33gr
13yds

Hi everyone. Received my Panthera last week and today I experienced that the safety is not working properly. Is there any adjustments with the trigger like on the impact to fix it ?

I have Operatives taking down a "Tree" in my front yard right now!
There was a good chance that the winds would help "Tree" attack and destroy my house!
So I went with a preemptive strike!
Skilled operatives, armed with the latest chainsaws, are strategically removing this threat as I type!
'Operation Sap' had been in the planning stages from the moment the pending attack by "Tree" was verified by Highly Trained Personnel.
Reports from the front line of this Operation state that, by end of day "Tree" will no longer be a threat to the future well being and peaceful nature of this domicile.
Rest assured, all "Trees" on this property are being carefully observed for any signs of future terrorist intensions!

As a show of good faith?
I will give all "Trees" living peacefully in the boundries of "Mama's Land" 30 days to pull back from the shooting range.
After 30 days? I WILL launch 'Operation Clear sight'.

Please excuse my ignorance, I am new and trying to learn about Pcp rifles. Does the tighter or more pressure a hammer spring have effect the power of fps ?

UPS just dropped off my $1100.00 AGT Vulcan 3, pre-ordered from Krales on 1/20/23, without ever requesting the $66.99 Import Duty Fee. Is this payback for the good Karma I've earned picking up trash during my Adopt-a-Highway program? WM

Ok, I give up, I've got a Maverick .22 Compact, I've got both FX Hybrid's 22gr and RMR 22gr slugs and I can't get them to work for beans, bumped up the reg pressure, standard liner running the slug side of the transfer port, heavier spring and weight, Huma and yet, I can't get the darn things to go fast enough.

I know this has been discussed before but here's my issue - my stock .25 cal FX Impact will occasionally become inconsistent in poi and extreme spread. Replacing the breech o-ring resolves the issue. This seems to happen after only 2-3 tins of pellets - so about 600-900 shots. This seems excessive to me. I'm shooting 34 grain JSB and FX diabolo pellets. 2nd reg is at 120. Pellet probe has never been removed. This has only begun within the last few months - did not happen when I bought the gun a little over a year ago. The last two o-rings I used were from Captain O-Ring. Any Suggestions?

Hi,

I am finishing a small HPA filling station using a Tuxing single piston compressor
with a permanent water coolling circuit. I am waiting for another 3 fans and the
installation of the Tuxing gold filter.



You may have seen on Amazon the incident with a Tuxing filter torn in half.
I asked Tuxing about that and they told me that the buyer never bought
from them on Amazon and that he could be a competitor or false accusation.

Despite that, I want to make sure that the tube is safe as possible. I will be
filling up to 250 bar maximum, usually 230 bar. I've seen similar tubes failing
at the threads and injecting the cap...

Do you think its a good idea to use a clamp like in the photo to compress the
tube around the threads? I think that a rapture might be safer than an ejection
of the caps. What do you think?



Thanks.

.177 marauder. Includes
Bullpup stock
Adjustable rifle stock
New lane regulator
All parts that were removed for the reg
4 mags and single shot tray

Want to trade for lever cocking instead of bolt. Arthritis makes using the bolt to dificult

I am looking for someone to make me a .22 probe for the Skout Epoch. I may need some help getting the FX liner to fit in the Skout barrel tube as well, but I may be able to handle that one on my own.
.22 Magazine inserts or 3d prints will also be needed. Possibly a single shot loader.

Let me know if you would be interested in taking on this project.

This rifle is in great condition. Low shot count. No modifications. This rifle is regulated. Check out Air Arms site for specs on this rifle.

All originally supplied accessories. 2 clips. I am including a DonnyFL 1/2x20 UNF Double Male Adapter, a $40 value (a moderator is NOT included). I am including the adapter to charge the rifle as well.

Asking - $900.°° plus shipping. "Reasonable offers" will be considered. May consider trades.

I ONLY SELL AND SHIP IN THE CONTIGUOUS UNITED STATES.

Payments accepted - Cash App or PayPal accepted. FF or add 3% for fees.

In 2019 I got the bug to buy a pcp gun and sold 9 spring guns, bought a Diana and ended up selling it and getting a FX dreamline.
Last summer I realized everyone needs a good spring gun and bought a 97k because I'd never owned an underlever.
The gun is heavy but it's definitely got that german craftsmanship like the RWS and Feinwerkbau rifles I sold.
The 97k is a little picky on what pellets it will group well with but overall a really nice rifle.
I've put the Weihrauch moderator on since I took this photo.

I have a fairly new RAW HM1000x in .22cal that I wanted to see if it would shoot slugs with any accuracy. It's set up by Martin to shoot JSB 25.39gr pellets at 950fps.
I bought a bunch of NSA slugs and started testing. The card I have pictured is at 15 yards. If anything shot halfway decent at this range I'll bring it all outside when the weather warms up. The RAW has a polygon LW barrel with little to no choke detected after pushing a few pellets thru by hand.
I didn't change any settings from the pellet tune. The 23gr NSA are averaging 965fps, the 24.8gr at 920fps, the 27.5gr at about 865fps. I had some FX hybrid22 gr on hand and it pushes them at 985fps.
Results as you can see: None were as accurate as the JSB pellets. It looks like the barrel slightly favors the .2175 and .218 24.8gr and 27.5gr slugs. Not sure if its worth going outside with any of them if they can't print a 1 hole group like the pellets. What do you think??

Jerry

So I've been looking around trying to find some slugs that might do well im my Beeman Commander. It's a pretty cheap gun but I'd like to make them work and fool around with them if I can. Im aware of barrel diameters and slug weights and that guns can be super picky. From what I've seen Fx Hybrids seem like a good option but really costly. The H&N sample pack looks pretty good too. I really want to get ahold of some NSA slugs but I can't find a sample pack anywhere that doesn't charge $30 and up for shipping. Any suggestions for other slugs? Does anyone know where I can find a NSA .22 sample pack?

After two years and 3,000 starlings later on this farm, they are finally almost all gone. Here is the last of the videos I took from that farm. Has anyone else had success getting rid of them?

I finally got my scope and rings in and on. After spending some time, trying to zero the scope, the best I could, I tried 10 shots with four different pellets from 25 yards. The differences between the pallet groupings is so dramatic, but you can see which varieties it seems to like best. To be honest, there are probably other variables like my being a bad shot but I tried my best on all of them.

FX Crown MkII Saber Tactical Chassis Version

• .22 Cal 600mm Superlight STX Superior liner
• 480cc 250 bar carbon fiber bottle
• Saber Tactical folding aluminum chassis with adjustable length of pull, comb height, butt plate height and angle.
• Comes with one magazine, foster fitting, owner's manual, and original case
• Price is $1,600 shipped inside of the continental US
• Will accept PayPal payment
• I also have a 500mm .22 cal Superlight STX Superior barrel kit that can be fitted instead of the 600mm or purchased in addition to the 600mm for $200 more

I purchased this gun brand new from Utah Airguns in November of 2022. It has not been shot much and all parts are original. It is in excellent mechanical and cosmetic condition. Please reach out to me with any questions you may have.

Diana 460 in very good condition. .177 caliber. Piston spring (Vortek) and seal replaced 4 years ago and has seen little use. In safe all the time as shoulder is too “old” for springers. Metal and wood a solid 90-95*. Muzzle modified with custom mod and is much better looking than factory set-up. Cocking lever held in place by strong magnet. Rifle will go for $275 plus shipping. RWS lock-down scope mount included, Hawke Eclipse scope is not but can include for extra $150. Shipping where allowed is extra. On “old” Yellow BOI a bunch of times, all positive, a few here. Thanks for looking.