Hello, I’m in the Portland area and new to the site. I got into air guns when some rat traps “didn’t meet specs”. I’m looking for places to shoot, people to shoot with and maybe some pest/invasive species control opportunities.

My arsenal is limited to a .25 Hatsan and a .22 American Classic but I’m looking to expand.

A couple years back I decided to have my D34 tuned and a Vortek kit installed. I shipped it to a reputable Smith and things were just groovy. Upon return the box was damaged but the gun looked fine. I mounted a scope and zeroed it. No problems. It shot beautifully.

A few weeks ago I decided to take the scope off and shoot it bare. When I zeroed the iron sights I noticed the back sight was screwed left almost to the limit. A quick check revealed the scope too was zeroed almost to the limits of the windage screw. A careful check with a straight edge showed a very slight, almost imperceptible bend to the right. It must have been damaged by UPS when they shipped it back. I just didn't realize it.

I did some research and decided to bend the barrel back to center. I made sure the front sight was plumb and centered the rear sight. I made up a maple jig that fit the barrel then set the whole mess in my bench vice and proceeded to add pressure.

A straight edge across the top from the front post through the rear sight told me exactly how much bend I was giving it. I would apply force until I got a bend and then test fired a pattern.

I started slow and the first few tries the barrel would just spring back to the same POI. But after a brief learning curve I started to make headway. The gun started out shooting 4" right at 10 yards. After 13 "bends" I got the pattern right in the middle of the dot.

I optically centered the scope using a mirror and mounted it on the rifle. It was 4 clicks right and 10 clicks low at 25 yards.

The entire process from making a jig to sighting the scope took less than 2 hours. The gun shoots as good or better than it did before. No affect on accuracy at all.

I sweated and fretted the first few bends. That barrel was WAY over to the left when I put pressure on the jig. But it sprang back nicely. When it was all said and done you couldn't tell it was ever bent. Now when passing a straight edge across the (centered) sights it comes across the center of the receiver at the rear. When I started the process it was at the extreme left edge.

I was so happy with the results I decided to bend a hatsan 95 barrel that had snapped up and bent. It was easy. 3 bends and it brought the POI back down to zero at 25 with an optically centered scope. The iron sights jibe perfectly. I didn't touch the scope adjustments at all to get zero. The rear iron sight is pretty much centered in its vertical travel. Horizontally it zeros exactly in the center.

What a hoot. I would have never thought you could bend a barrel back straight again with a stick and a vice. Well I was wrong. You can. It's not difficult at all and it's a bunch better than dealing with adjustable mounts and scope shims.

Attached is a photo of the rifle and the jig I made to straighten the barrel. Just a piece of maple cut to length with a lug at both ends. I cut a saddle in the front lug for the barrel. The rear lug is square and rests against the pivot block. It's as simple as clamping it in a vice and turning the handle until you think it bent a little. Then test firing and repeating until the rifle's POA and POI are in the same spot.

Re my Commander XR Magnum in 5.5mm:

I got it about 2 weeks ago. New. I spent 2 weeks testing virtually every pellet and slug in various head sizes and weights from 18.1gn to 33.956gn. I am obsessed with accuracy and shoot for an hour or three in my backyard at 50m. I demand very low single digit standard deviations in velocity. I am experienced in tuning.

I've managed to get my SDs where I want them but at 30m the all I get is 3/4" or 1" groups no matter what pellet or slug I use. I run my pellets at 888 fps or so and slugs at 1009 or so.

I've checked for loose screws and bolts, The barrel and shroud is tiht as it should be.

I've tested it with moderators on and off. (no difference)

This type of group is regardless of what ammo I am using and I've varied the speeds to see if that made a difference. It hasn't.

I've changed scopes, optical and digital to see if it was a mounting or scope issue. It isn't.

I clean my barrel every 100 to 200 pellets.

So far I've shot well over 1000 pellets/slugs with the Brocock/BRK Commander XR Magnum.

I am not shooting in moderate or strong wind.

I am looking for suggestions as to why can't I get the tight MOA groups that I usually get with my other PCPs

PS: I also have a Commander XR (not Magnum) in 5.5mm and I get MOA accuracy from it at 50m.

TIA.
#Brocock #CommanderXRMagnum #Accuracy #NotAccurate

I received this wonderful Cometa from Jon tuned and with a brass trigger! Mounted a Hawke 3x9 scope and ended up with a tack driver. Easy to cock and a pleasure to shoot!

I have a Beeman under lever with a composite stock. I'm looking to trade for or purchase a wood stock for the same. Mine is in great condition, no marks at all. Not a flimsy piece of plastic, pretty solid. Has a built in magazine holder. I'm just wanting to change things up a bit.
thanks
Mike

Check out this video of us taking the M4 out on a Prairie Dog hunt to see what they were capable of!


*Warning - video contains Hunting content*

I just mounted this Seals 6x24x50 scope on my QB78S rifle. And so far it’s a good combo.

Bone stock Notos and as my first mod I did the FX 500mm barrel kit. I chose the superior heavy liner as I plan to mainly shoot slugs. I haven't touched anything else but the barrel swap.

So I was shooting 15.4 gamo pellets @740ish and 23gr NSA slugs @ 650ish. After the 500mm kit I lost quite a bit of speed. The 15.4s are 660ish now and the 23gr are 550ish.

Any one have an idea as to why? More curious as to understanding why the loss in speed.

I plan to fully port and big bottle/reg swap too along with custom spring and hammer stuff too at a later point. So I know I'll pick up speed at a later point.

Max armory taking pre orders.

Hello all!

I've got two PCPs right now. An Uragan 2 600 with laminate stock and an FX Dreamline tactical with bottle. Both in .22
I've got a buyer for the dreamline and I'm thinking I'm going to let it go.
The thing is, I love my uragan to use mostly as a bench gun, but to use as handheld is just too heavy with scope fot hunting. I can use it, but is not ideal. The gun is 3500gr, with scope and silencer (Donny Sumo) is around 4500gr.

I'm looking for a really light but with some power in .22 setup to use on the go, but that is capable to shoot up to 80yards.
I could just use my Dreamline and adapt it, or I could sell and buy a new shorter and light gun.
I looked most into the Airmaks Krait (powerful, short and 2500gr) and to the BRK Ranger XR (less power, also 2500gr but should be really shouldable), but I'm open to anything really. The FX Panthera compact hunter also looks good, but a bit heavier.
I was also thinking of using an primatic scope like the Element Immersive 10x or the MTC to lower the weight, or a really compact scope like the vector veyron.

So, what setup would you guys sugest for compact shoulder hunting?

Is there a free website that will tell you who owns a residence by entering an address?

I’m pretty sure everyone knows about the NEW FX IMPACT M4 , I saw Justine’s video and basically FX did a facelift to the gun with a few changes, I would like to see your thoughts and opinions. Be safe

This is very different than small bore, power, and shot count come to mind quickly. However, the accuracy issues and recoil also will reveal themselves as one pursues this niche of the hobby. From my limited experience, AAA is the gold standard, AEA is very affordable! However, how many others are there really? Not a small bore attempting to pass itself off. Now there is the Bulldog/ pitbull. As well as the Russian ataman series. What is the real shot count and performance of these bad boys? Thanks

If anyone see parts they want that are on my akela just hit me up i tell you where to get one.

Guys, is it only me or is it really more convenient to have a charging handle on the left side? I'm right-handed, and recently I got in my hands a couple of Marauder bullpups that were converted to left side charging handle. Before swapping them out to the right side, I tried shooting them and it actually feels good. Especially for bullpup configuration. I don't need to let go of the pistol grip with my right hand and can keep the rifle sighted, while with the left hand I can feed the next round. I wonder if anyone has the same experience and prefers the charging handle to be on the left side instead of the right. Thanks guys!

Let me explain, first off, I love BOTH of these platforms. But, for competitive purposes, let’s critique them. Appearance, epic, either version, carbon fiber wrap gives a sleek appearance. Power capabilities- equal, Vulcan 3 is a bad dude! But so is the Epic. The irritating hammer pings? Well, the Epic 2 had it, hands down but is a longer gun. But, with the ability to adjust the reg significantly higher, you cal use a shorter barrel. The Epic has an external adjustable reg, Vulcan 3 does not. Both have unchoked barrel. Both have big power. Now, the epic 1 hasn’t appeared yet, but the Vulcan 3, as awesome as it is, will finish behind. But! The Vulcan 3 is about $400 cheaper. It’s also a robust platform. Upon reflection, the Eastern European dudes got their sh** squared away. JMHO.

I currently have a avenger .25 and I'm wanting jump into a better long range rifle something capeable and accurate enough for rabbits or other critters out to 100 to 150 yards. I was contemplating a fx m3 but now I see the m4 is coming out it would be a bit before I pull the trigger on a new toy. I'm just wondering what would be a better caliber I would also want to use it for extended Prarie dog shooting. But mainly for them lil evil threatening rabbits that are teasin me outside the range of my avenger

4 new tins. $40.
Free priority shipping 50 states

Hey All,

In culling my 100 yard bench rest candidates decided to move along my .22 RAW HM1000x.

Gun is laser accurate but with my RedWolf HP .22 and FX Crown .22 etc. I have decided this one needs a new home.

Shoots the Redesigns right at 950 and surprisingly the 22.07 JTS pellets at 1010 are just as accurate (did a post on the forum about this a few days ago along with a pic of 40 shots at 100 yards)!

Gun has a Neil Clague moderator on it and is whisper quiet (seriously, insanely quiet)!

Comes with a couple mags, Neil Clague moderator, single shot tray and will ship in a hard case.

Scope, rings, Atlas bipod not included.

Say 1150 and will split the cost of shipping and insurance. PayPal for pmt.

Got an opportunity to buy an impact 2 with a 22 and 25 cal. both 600mm with slug liners.
Shogun moderator
Mtc viper pro 5-30 and fx rings
Adjustable butt with monopod
Adjustable cheek
Sabertac bottom rail
Plenium has been upgraded
Power kit
2019 cf tank. With nice cover and carry strap. Think it’s the larger one. He said it was 800 when he bought
Some kinda of compressor. Didn’t check it out but was blue and is ac only and has water lines and pump to keep cool. From a quick search looks like a 250 dollar one
Has 25 cal mag but no 22. Has 3d printed single loader
Is 2300 a deal. I don’t care for the scope and 25 cal and the adjustable butt

That copper m4 is really calling me! This will
Be my first pcp

Thanks

American Air Arms Paradigm .30 camo laminated stock. Rifle new to me from AoA September 2023. Gun has a mark on it from when assembled at AAA where the tension nut meets receiver. Best I can figure is their wrench slipped when assembling. There’s no depth to mark, it’s just an anodize scratch. A marker of some kind would probably hide it but it’s not my desire to deceive anyone. Includes factory box and one magazine.
I sighted it in and then used it strictly for pesting. It does not have even 150 rounds through it. The Paradigm is everything all reviews say it is. Reason for selling, I’m switching gears on my hobbies and I don’t save/collect previous hobby gear.
I do not have PP or Zelle or any of those methods. I accept cash, personal check, bank check, USPS Money Order. I have an excellent seller reputation, having sold 10 or 12 PCP’s here on AGN. My ad is 100% truthful. I provide tracking as soon ad I get tracking number.
Was $2600, now $2100+ shipping within CONUS. My loss is your win.
Additional photos on request.

Alkin W31 compressor. Came from Alkin Compressors, Clifton NJ on 1/27/2022.
Comes with all paperwork (manuals), 92 ounces of oil for oil changes, unless it’s picked up it will ship dry. Almost ready to turn over 5 hours. Runs perfectly. Includes 240 volt male plug and female receptacle and 4” square electrical box for outlet, one drier repack kit, male DIN300 and female Foster fill whip ends. Manual drain.
Can send additional photos on request. Moving away from PCP’s so will just collect dust if it stays. Has lived it’s entire existence indoors, heated and air conditioned. I have the original skid and factory overbox. Pick up would be great but shipping can be arranged at buyers expense. It would need to be picked up at my residence with a truck with a power tailgate because believe it or not, I don’t have a forklift.
I am willing to deliver within a 3-4 hour radius of Mentor, Ohio (pretty close to Lake Eries south shore) if buyer arranges rental of a van.
$2700+ shipping arrangements.
I do not have PP or Zelle. I accept cash, bank check, personal check or USPS Money Order. I have an excellent rating on AGN and accurateshooter.com
Machine is exactly as stated in perfect condition with no repairs having been needed.

Up for sale fx impact mk1.25 cal 600mm barrel

Fx Power plenum
Fx 20 moa scope rail
Fx full length cheek riser
Huma regulator first @160bar w/gauge and second @110
Stx superior liner w/cf sleeve
Stx rear block
M3 power wheel
1x 26 round side shot magazine

Tune for jsb king heavy mk2 @ 895 no leaks or issues, very accurate.

Bipod not included.

$1100 + split shipping cost paypal or zelle

American Air Arms Evol 15” barrel .22 caliber. Comes with factory soft tactical case and one magazine. Bought from AoA October or November 2023.
There are tiny marks where magazine sits in receiver from normal install and removal of magazine, otherwise the rest of the rifle is perfect. I have nearly a tin of JSB 25.39’s through it. Bought it for 50 yard plinking and is everything that reviews tout it to be. I’m moving in a different direction in my airgunning and do not want it to just sit in a safe and get old. Ad is 100% honest. I have an excellent seller rating on AGN and accurateshooter.com
I do not have PP or Zelle. I accept cash, personal check, bank checks or USPS Money Orders. I provide tracking number as soon as I receive it.
$2000+ shipping to CONUS.

This is a no right or wrong answer question. In the pursuit of accuracy, there is target and live. My buddy in California shoots tournaments, hence target, but loves to smash tree rats and trash pandas .
My other close partner has zero interest in shooting pests, but is a strictly slug shooter for tight groups. Me , on the other hand, my end goal, whether pellets or slugs, is to put lead to targets! Live , or paper/ metal. My goal is have every niche tool for every reasonable application. From mouse to coyote, from 10 yards to 100 yards. Now I find all 3 ventures viable. Just listing preferences, we respect each other’s decisions.