I have an AEA Challenger Pro .22 rifle. It is a great shooting gun and 6 months old. The O ring blew between the gauge and tank. I contacted the vendor, ie, Utah Air guns. They told me they don't work on AEA guns and to contact the Pellet Shop. I did and they sent me a new O ring but wrong size. I recontacted them and they asked where the gun came from. I told them Utah Air Guns. Pellet shop now refuses to send correct part or deal with it. Now I sit here with a nearly $900 gun, including extra clips, that leaks air. DOES ANYONE KNOW A VENDOR WHO WILL EITHER SELL ME THE NEEDED PART OR FIX THE GUN FOR ME IF i PAY ALL EXPENSES. I am aware that O rings are not covered by warranty. BUT, I now wonder,,, what if something actually serious went wrong with the gun since there is obviously no vendor support for repairs nor any warranty in spite of what is claimed. This has been going on now for 6 weeks. I am pretty disalusioned and likely will just sell the gun and forget the whole pcp thing. Also I have looked on line and see no video's in which I can learn how to change o rings or much anything else on most pcp guns. So what do you do when there is the eventual problem?

The ZELOS comes from the factory at 2000PSI regulator pressure and it can be turned up to 3000 PSI. When I turn it past 2500 PSI I get no increase in velocity. I would like to get my 25.4gr going 920 FPS but can only get a consistent 905 FPS. When I go to 2750 Reg Pressure the velocity goes down a bit to 890, the same velocity I can get at 2300 PSI reg.

Why does me velocity not go up between 2500 and 300 PSI? There is no HST adjustment that I know of on the Zelos. Is that the problem?

Once I increase the reg do I need to shoot it for a while for velocity to rise?

This summer I started “pest control” with a Diana Model 34 (circa 1998) air rifle passed down to me by my father-in-law. I’ve been impressed with the power and accuracy compared to the Daisy BB guns I grew up with.

I was having such success using just the iron sites that I figured I could get even more accuracy by adding a scope. I bought a Vortex Optics Crossfire II (4-12x40 AO). As soon as I installed the scope I started missing. I zeroed in the scope (several times) but it never stayed put. After several weeks of frustration, I removed the scope and started killing the varmints like before.

So here’s my question…Should my Diana 34 be worthy of a scope? Is it possible that a break barrel wears out to the point that the barrel doesn’t snap back into the same position each time? In my mind this would explain why I seem to be more accurate with iron sites. I’m not as young as I used to be, and a scope would help.

The Olypsys Tech was a Pretty important part for The O-Ring Store, LLC Getting ISO 9001:2015 Certified Due to Quality Control, Making Sure we are Receiving the Correct Sizes, Shipping the Correct Sizes to Customers, and Keeping Record of it.​

We Use the Pro Vision Booth with the Pro User License but there is A free Version Available you just have to buy the Grid to start Using it, or buy an O-ring Kit that Comes with the Grid, For Example https://www.theoringstore.com/store/index.php?main_page=product_info&cPath=175_174&products_id=24381​

Another Useful aspect of it is Crossing the OEM Part numbers to the Metric Size or a Standard Size, So you can Spend $0.10ea on the O-ring Instead of the $5ea from the OEM. Once you get the Size Getting the Correct Material and Duro is Easy. Air Rifles i Always Suggest using The Disogrin (TODI Urethane) Its more Expensive in the short Run but it will be alot Cheaper in the Long Run​

​

Were are Going to have a Quick 15-30min Webinar on using the App, Feel Free to Send me your Contact info and ill get you an Invite. If you have Any Questions, if, ands, or buts feel Free to Contact me as Well.​

Here is the Link to Olypsys on our Website:​

​

​

Can someone explain the value of a one way check valve when filling an air tank from a compressor?
Thanks,
Barry

The Texas heat or this EDgun Leshiy 2?!!!


4k - no audio


1080p - audio

I found a few post about AVS slugs but nothing very helpful for my question.
I'm interested in the bases and options for hunting and accuracy.
Does anyone have experience with them in .22 and .25 in FX impacts?
I ordered a couple tins for .22 and one for .25. I chose the hollow base in weights a few grains heavier than what I've tested.

Since even this forum is caving, where and how do we buy used mods? I need several and prefer buying used to save a few bucks.
Another forum?

What is the build quality of an EDGun West Leshy 2 like? The specific gun of interest is the 35 cal hi power. Specific questions:

- how is the barrel mounted to the receiver?

- is the receiver one piece or bolted together from many components like an FX?

- what parts are polymer?

- does the folding "back half" of the rifle lock up solidly to the front?

- does that quick mount for the Behemoth silencer make a stable, ridgid connection with the barrel?

- is the barrel a rigid steel component or a "liner in a tube held by spacers in a shroud"?

I'm asking this forum these questions because I have completely lost faith in the "airgun influencers" promulgating marketing points on social media. I would very much appreciate an owner taking his time to comment on how well satisfied he is with the Leshy simply because he has found something that delights him. Alternatively, I would appreciate being warned away from a steaming pile of over priced, shiny aluminum alloy crap even more.


Kind regards,


Mike

Oops. I slipped and fell on the BUY IT NOW button. Have been in need of a pick me up, and the timing was right on. KRALE in the Nederland was happy to take my card and was even careful about ID theft and fraud. I appreciate that after the runaround I got from those guys in Canada.

The package is a Reximex Tormenta in .25 with a couple of extra magazines, in synthetic. I have nothing against the Walnut stock, and may pick one up later just because. I already have a Kral .25 Knight that has done OK, but I feel that I have maxed out its potential. The Knight is quite large and a bit unwieldy for field work. The Tormenta should fill in the Airgun quiver nicely.

Glass is to be decided. Reximex claims 40fpe stock. I will shoot it before I change anything.

Arrives Wednesday.

I am not a bench rest shooter as I lack the talent and discipline needed… What I do mainly with my airguns is plink and pest. To that end I’ve found through lots of shooting that three shot groups best represent my skills. And because I rarely get a second attempt on a missed critter, three shot groups work for me. Two groups at forty yards tonight after work, Ghost Carbine sending JSB Exact Jumbo 18.13s, bipod front, shoulder as rear bag.

Here are 2 groups of 10 shots each from 30 yards (max distance where I'm at).
These are FX 34 gr .25cal pellets.
I prefer slugs but am looking for a minimal tune for max shots to plink in the yard.
My settings are 1 on the big wheel and 2.25 on the QTS

Reg 1 at 130 bar

I haven't gotten a full shot count on a fill yet but as soon as I do, I'll share it.

Do any of you have results you'd like to share for a minimum power max shot count setting? I love the group and the info here is excellent. Thanks for sharing and reading.

So fx made the pocket chrony. Then they also made the chrony display. So why didn't they just make 1 product that read the speed and also display the speed? Each product cost $250. So that's $500. I was going to buy them so I don't need my phone but then saw the garmin xero c1. Like wtf. It's a pocket size chrony that will read your speed and also display it at the same time. Price is $559-600. So why the heck fx didn't think of putting both into a single product. Wtf is up with making 2 separate device? Come on fx. Well no brainer, garmin got my vote and money on this one.

So I have a slug A liner in my fx impact 25 cal. I only shoot nsa slug cause I find it's the cheapest slug vs all the other slugs. I shoot 36 gr nsa. I have 10 boxes of them. My slug A liner does about 2 inches groups at 100 yards. When I say groups it's at least 5 shots to 10. Not 3 shots like some ppl doing. To me that is ok but I would prefer under 1 inch at 100 yards or is that too much to ask for. My gun is tune to shoot them at 960 fps and 150 bar. I was wondering would the new superior heavy be any better to get tighter groups with nsa slugs? The only video I see someone testing superior heavy vs slug A liner is ted. But he only tested with fx slugs and knock out. He never tested with nsa. Have anyone shoot nsa slugs from superior heavy and slug A liner can fill me in if I should folk up $110 plus shipping and tax for better groups. I don't wanna spend money and find out it is worst or the same. Then trying to sell it back on here and get low balls.

Looking for some info on taking my notos to Canada from the USA.

I searched and the requirements aren't clear, I know i would have to declare it and fill out a form due to the foot pounds of energy and fps it shoots, but what about barrel length?

I've read rifles need to have a barrel length of 18", does this apply to air rifles as well? Any other advice welcome.

Pic for attention

I have a marauder .22 no leaks works perfect. 300$ shipped my number is 601-641-1504

Where have you found good used airguns where you aren't paying near-new airgun prices and where you have confidence in the vendor? DO they package your guns well and ship them in a timely manner? Has it been a crap shoot or consistent? How have your used guns (from the stated vendor) held up over time?

For weeks and weeks I have been fighting a silent battle in my head (couple of you know because we keep in touch) about offloading some guns again and making a transition heavier towards BRK, Daystate….I willingly took a loss on 3 very expensive semi auto guns as a trade in to buy a and a Pathfinder today because of my very pleasant experiences with the dealer time and time again. Everyone at the dealer is top notch. I willingly took the loss to avoid dealing with folks that don’t understand the beast and would blame me for something they did incorrectly which may cause a malfunction. Trading it in at least it’s peace of mind at a loss but that’s ok. Please stay neutral and please don’t name brands and dealers (no pointing fingers) This is just my personal experience. When you buy a BMW or a Mercedes you expect awesome service right ? Guess it depends on the day of the week. My BRK dealer is awesome no questions asked guess we’re going to be driving a Bentley (British gun) a lot more. If you are thinking about buying anything message me I have owned a ton of guns. I will give you my personal experiences with the whole package. At the end of the day you might as well buy a Yugo If the Range Rover isn’t going to come with great service and 100% be ready to use without oil leaks

I’ve been looking into getting a Daystate Huntsman revere regulated since I only here great things about them my question is do any of you have the 25 cal version regulated and what kind of out the box power and shot count are you guys getting who have one

Or is it obvious to others when someone wants to sell or buy something?

The long awaited Mora has finally arrived at Talon Airguns...
In stock now.. .357, Standards and Compacts

RTI Mora Sniper 700mm AirGun - High Power Air Rifle Products

https://youtu.be/YZaEJb7aTU0

talontunes.com

Hey all,

So I’m new to PCP air guns - I had a few other co2 and springers, but this is a first. I went with the Avenge - X full synthetic. Looks like you can swap out to the tactical stock. I guess Im getting at which one?? There is a tactical stock chassis, a saber stock, ect.

I have the 210 tube not bottle - can someone send a link? If that’s allowed - first time posting

Thanks!

WTS, HW45 .20 caliber. I purchased this new last month for absolutely no reason, I haven’t shot it, all I did was add Hogue rubber grips, original wood grips are also included. Brand new, mint condition. I will include three new tins of sealed H&N 11.42 Grain .20 caliber pellets.

$385 PayPal’d (Family/ Gifted) and shipped to the lower 48. Great deal, no reason to buy new.

I’m new to swaging slugs. I have a pressslug and set it up but don’t know what settings with the dies I should use etc. I’m swaging .22 slugs. And what lube are people using to swage? Thanks y’all.

I just want to reiterate the problems a tick bite can bring you.I think we all are aware of the dreaded diseases they carry.If you get a bite go get the medicine as fast as you can, better to just practice good sense, like wearing colored clothes, having tick spray, looking for the rascals when you take your clothes off., also checking out your dogs and pets.....ticks feel vibrations and can jump on you. I think the ticks were on the rats and caused the "Black Plague" Now I think it was fleas, another scum bag bug