Daisy Powerline 881. Just been sitting in the safe. Foam wiper turned to dust when I went to pump it. It does give a SLIGHT pop when I pump it but I assume it needs a rebuild.

I am in SoCal 92883 area. It ain’t worth much so would rather not deal with shipping if anyone local is interested.

$50 bipod not included

A few months back, I bought a pre-owned HW95N in .177 cal from AOA. It was in perfect condition and looked brand new. Like #1. I shot it some in my 10M basement and the accuracy was atrocious to say the least. It barely could shoot a 1 inch group and being a match shooter, I was sorely disappointed to say the least.

After about 100 shots, my head was spinning because of the twang and I had had enough. I bought a Vortek HO spring kit. I took it apart and found the usual greasy mess inside, so I degreased it and installed the kit. After that, the twang was gone, but the shot cycle was very snappy and it was still shooting 8.4s around 870 fps. I shot it another 250 shots figuring it would settle down-nah! Some say you should break in a gun by shooting it 2000 times. A waste of time an pellets IMO.

Took it apart again and found some galling on the spring guide. I ordered a 12 fpe spring from Vortek and after cleaning up and polishing the galling, I installed the spring, lubricated everything, and reinstalled the kit. Now it was shooting 13 fpe at 830 fps. It was easier to cock and the shot cycle was smoother, but not great. Accuracy was where I wanted it to be and if I did my part, I could shoot one hole 5 shot groups at 10M. It still sounded rather snappy, though. After about 150 more shots, I was shooting at my indoor range and when the gun fired-WHOA- it sounded entirely different. Instead of the usual snap, it went THUD. Not being very experienced with springers, I now know what others describe as this kind of sound which is desirable. Like #2. I went to the outdoor range and shot the rifle at 50 yards and was getting some really nice groups. After I got home, I tested it across my Pro-Chrono and velocity with the AA 8.4s was 840. There's a lot of power potential to this rifle.

Observations:
1. Trying to get high power out of these springers is achievable, but not very comfortable to shoot. Good for hunting where you don't take a lot of shots, but I really prefer energy closer to the 12 fpe level. Maybe the Brits have something there.
2. This is the third HW rifle that I've had experience with. All of them needed a replacement spring kit. Weihrauch should be ashamed of themselves for building beautiflul guns, but installing sub-standard springs and doing a sloppy job with internal lubrication. My R7's spring was turning into a banana after a tin of pellets. It didn't break, but the power was low no matter what weight pellet I used. It now has a Vortek kit and is starting to thud like the 95 and power went up 2 fpe.
3. I now have two good performing HWs that live up to the reputation they deserve.

See These two shots at 132 yards:

I'm considering QD Fox as a source of after market magazines for my AGT U2

How do these stack up against the factory product? The price diffence isn't significant enough that it would trump buying them over the AGT mags (which are very solid and reliable) ....unless they are awesome.

Hajimoto Productions is selling some Zelos related things the HUBEN bottle adapter with an adjustable regulator built in , and offers the HUBEN with a 500 cc , or 700 cc CFB .
I used a c88machine bottle adapter $50 , and a round bottom 500 cc bottle from Amazon for $40. I would like a bottle barrel band for it with a pic rail.if any of ya all know where one is. I have 2 different tube pic rails one is from Natchez came with rifle no barrel band. The other is from Pyramid Air came with 2 ND Zelos , and has a barrel band although it was not in the pics on website.? I put them on a tube together for informational purposes in the pics. I will post a pic of the bottle as well in a edit in a few minutes. One of the bottle pics was upside down?

So I have a FX Dreamline with a 500mm barrel in .22 cal. It's pretty dang accurate shooting Diablo Exact pellets. I'm wondering if switching the barrel liner to a slug liner would increase the accuracy at 100 yards. I would love to hear your thoughts and what slugs you like to shoot.

I have a 2016 HW 100 KTL ,it is tuned at 21fpe with JSB 18s and is lase accurate. It had the small air cylinder, in 2022 I bought the large one from AOA. It comes with both cylinders, 4 mags, degasser, complete reseal kit, and gauge and fittings to adjust the regulator. The scope and mounts are not included.
The gun gets 4 mags per charge ( 56 shots ) on the lg cylinder and 3 on the small and is changeable in field.
Both tanks have marks where I changed the gauges from one to the other but are pretty much covered ( see pic ) and one spot on cheek rest. Other than that it is flawless, holds air great, and extremely accurate, annd whisper quiet. Asking 1000 shipped , 1025 west. Having trouble downloading pics .Let me know and I can provide what you need.
Thanks
Chuck

Looking to trade my like new vet 2 standard in 25cal for something else in 22, and compact. Let me know what you have.

This vet has a delrin tipped hammer to help with ping, and the donnyfl quick hammer adjust knob. Comes with 2 mags, probe and single shot tray.



Scope not included.
For more pics or questions. Message me for details. Will sell outright too.

Thanks for looking.

I do not know everyone’s feeling regarding the dreaded windmills.
I do know that thousand of birds are killed everyday.
I do not need them and I hope you don’t.
This one WAS in Solano County, California U-S-A:

WTS: Snowpeak Max 1 .22 - $400 Shipped!

Price: $400 shipped CONUS.
Payment: Venmo, Zelle, PayPal (add $12 for G&S fee).
Email: [email protected]

Price includes everything below:

• Snowpeak Max 1 .22
• One magazine (20-rounds)
• One fill probe
• Shroud Adapter for 1/2-20 moderator (AEA Challenger Adapter #83)
• Original assorted o-rings.
• Owner's Manual

Note: Scope and moderator not included.

I purchased this Snowpeak Max 1 .22 earlier this year from Wes at AirgunArcheryFun. The gun is solid, does not leak (after it was fixed), accurate and gets a ton of shots on a 300 bar fill.

JSB 25.39's shoot at 896 fps/45 fpe with current tune and reg at 165 bar.

It's a great bench gun. But, for me, too heavy/front heavy for offhand shooting. The cocking lever is very smooth!

The Max 1 is being offered at a very competitive price, with a few caveats that I will note.

• The regulator gauge has few small scratches on it (see pic). It arrived to me this way, and more annoying than anything.
• The fill probe can be difficult to get in, so I just leave it in with a cap on it. Plus won't lose it now.
• The Max 1 was shipped to me empty, and would not hold air when filled. Wes immediately had it repaired. I was disappointed, but the gun was quickly fixed, and leak is gone.
• The shot string is very good (see chart), with many shots on a 300 bar fill! There is a very very slow decline from shots 1 thru last, but it still has a good ES SD (see chart).
• Similar to the Zelos, the hammer spring is very strong, and backed out almost all the way. Turning it in, doesn't do much, but the regulator setting at 165 bar (factory setting), works very well for this gun. The hammer spring is also at factory setting.
• Most important to note... There is sometimes slight counter-clockwise movement when the air cylinder is being filled and warm. Wes had me degas, and tighten as much as possible by hand. However, I still notice an occasional slight ccw movement when it has just been filled using my slow GX E-L2 compressor. It can move about the width of a sharpie pen or so, not much at all, but it shouldn't be doing that. I have put a marker on the cylinder to check for any movement, and easy enough to twist cw back if I want. Also, when warm, I can actually twist it slightly by hand (it has a 'mushy feeling'). When filled and cold, air cylinder cannot be turned unless a lot of force used. I never had a bottle gun, but assume that any slight movement is not normal.

If interested PM me, or email me at: [email protected] .

New, old stock. Not a scratch or ding in it. Walnut stock. Theoben stamped. OEM magazine included. Must of bought new about 25 years ago. No trades, third party, or international sales. Will ship UPS ground insured CONUS via Pirateship. Weight: 13lbs. Dimensions: 51" x 5" x 11". Buyer pays actual shipping charges. Will accept Paypal FF/Good and Services (+3.3%)/Venmo/Zelle/Walmart2Walmart or USPS MO. Asking $3000 + shipping.

After looking at Jarmstrong's conversion, I decided to do the same thing to my HW44. I had already outfitted it with the Rink Formgriffe stock (Shoulder-stocks) but decided to go all the way with the carbine conversion by replacing the pistol barrel with a HW110 .177 310mm carbine barrel. I decided to keep the pistol air cylinder because it was adequate for my needs. I get two magazines out of one fill and that met "good enough". I ordered a barrel from airgun spares in UK and it arrived in four days with no import tariff issues. I disassembled my current set up, removed the barrel (it just unscrewed), screwed the new barrel in, put it all back together and that was it. I got some additional guidance from J on some plastic holders for my vice to secure the barrel when I removed the old one. A little extra mussel power was needed because the barrel had locktite applied at the factory.

Original setup.


Finished Product

Prime deal video I ran across

So I recently made my first purchase with Lee spring, luckily I use a prepaid card and plan for purchasing because my original order was $46, I was charged $24 and part of the order shipped the other day now this morning they tried charging another $56, wtf 46-24=22 right. So I call and got the run around from 2 people then transferred to the big guy I guess and what a load I got, OK 2 shipments from 2 warehouses makes sense but about the additional charges he goes on to say how that's how there system works but in the end of the day it'll correct itself. Yeah right. The reality is someone thought I'd be a big company with lots of charges because of the variety of my order and they could get away with some extra because there's no way I'd be looking. We'll lucky I do look and plan for purchasing so there's not much extra there and they got declined.

Amazon Prime day

I bought a Nate Chronograph to check my tune on my .25 DRS Tactical. The chronograph had sensor issues so I messed up my tune. I received the replacement chronograph and tried to tune my ar but t couldn’t get above 630fps with regulator screw screwed out as far out as possible and hammer spring to max. I degassed and bottomed out regulator screw plus one full turn. The fps increased when the regulator screw was turned in and reached 925fps bottomed out with max hammer spring. The regulator adjustment is opposite of what I would expect, am I looking at a bad oring on the regulator valve?

I've been kind of obvious that my 392 is in it's way to Mac1. When I shipped it yesterday, I got the tracking number.

I was able to wait until last night, then I started tracking ... watching it go from Akron to Cleveland, and now somewhere SW of Toledo.

I have a feeling I'm going to be doing this a few times a day, until the "delivered" status shows up early Friday afternoon.

Is it just me being so psyched about finally getting the steroid tune, or has anyone else done this?

For those that know the history of aftermarket options, were there ever any bullpup kits available for the Maurader semi auto, or were they all for the bolt action, or would the kit fit both?

Also, where would be the best place to advertise that I'm looking for one, even if it's a paid ad? I realize finding one is a real long shot, so I want to make the best possible effort.

I'm aware the Akela exists, but I'm specifically looking for one that fits the Maurader. Thank you!

Hello, I am selling my Vulcan 3, 700mm on .22 Cal. I have shot less than a tin of 500 pellets and a few slugs through it since I bought it from Talon Tunes.
This rifle is in like new condition.

Rifle,+2 mags, +fill probe, +soft bag, + Bipod, + pellets/slugs you see on the picture $900
Element Helix 6-24x50 FFP Scope + FX Scope Mounts $300
If you take the entire setup, $1,150 (including shipping in continental USA)

If you want more information, pictures, etc., please PM me or text me at 737-281-6400.
PAYMENT: I can do PayPal either F&F or you cover the PayPal fee's. I can also do Zelle.
Thanks, Alex

Hello,

I already have a 74 cubic ft Carbon tank but was looking to buy a 98 ci carbon bottle off eBay. It was manufactured 11/23. I'm not sure of the brand.

I have heard the small bottles tend to leak; it is allegedly good to 4500 psi (same as my 74 cubic ft one). Has anyone had luck with the small bottles? Thanks in advance!

R/

jde

Was able to kill 12 last night. This short one minute video clip is of six of the best shots.BRK Ghost in .22 cal shooting 25.39 JSB Monster Redesigned ‘s at 950 fps. Pard DS 35 50 night scope, Eagle Vision rings, Primos Trigger Sticks with Bog Death Grip rifle rest. Listen closely on the first clip to the sound of the round hitting the rat. It actually echoed it was so loud.

I would like to pick up a P-Rod to tinker with. If anybody has one that they have considered parting with, please let me know!
PFA

Still trying to get my WC 22 w/slug liner to shoot anything consistently. Every string with slugs or pellets swings something like 40-60fps, usually more.
It seems to shoot slower the longer I wait between shots.
I've tried 80-90 bar reg up to 125-130bar with hammer from all the way in or all the way out.
It's hard to find the knee when the fps is jumping all over the place.

Here's what I've tried:
* new AMP second reg, no improvement
* new Huma extra hi press reg, no improvement
* switched between pellet and slug port, no improvement
* new barrel probe oring, no improvement
* new reg orings, no improvement
* many different pellets and slugs all the same horrible es/stdev.

Any thoughts

my next thoughts are:
* hammer strike consistency
* ???

After much debate I’ve decided to sell my EVOL mini .22. Gun is in excellent condition. Zero leakage. Comes with:
1) the gun
2) 3 mags
3) soft case
4) Donny adapter and Tatsu moderator (airgun use only!) factory moderator included
5) magpul adjustable butt stock (factory one included)
6) magpul grip (factory one included)
7) barrel removal tool
8) gauge removal tool
9) and since this is my last .22 6 tins of pellets
OPTICS NOT INCLUDED, But can be included for additional $250.00
Zelle or PayPal. If goods and services +3%
Split shipping and insurance. Located in So Cal.
$2200 (optics +$250.00) no trades