EaZy Trigger Fill for PCPs

[manabeknives]

Ok, an update from Wyatt and Brian at Ed Gun West.

They shipped out a brand new EzAY fill to replace my broken EZ fill which I purchased in January 2025.

I paid $150 to UA and I appreciate Brian standing behind the product. Hopefully it works once I get it.

Tips for EzAy fill users: Do not leave EZ fill on your fill tank valet open and/or pressurized over night. Also, you can safely fill guns to 250 BAR ( not greater) and it should work as designed. Do NOT leave valve open after you fill your rifle to max fill pressure. Be sure to close the valve on your big tank.

They are getting a lot of returns and repair requests because of the above issues.

My example to Wyatt today and he confirmed:

“ I typically fill or top off my guns at either the Regulator set pressure, or slightly above about 8-10 times during a 3 hour bench session. No bleeding until the ‘end’ of my session. Then I bleed tank only ONE time saving a good amount of air I believe anyway. “

Anyway, hoping this helps.

Tom

Thanks for the update Tommy
Only to 250 bar....hmmm
Nope...it stays in the box as a costly reminder not to buy gimmicks + i couldn't sell it in good conscious. I think it is junk
Hope the repairs hold out
Mike

 

[bigHUN]

I don't want to be an @rse but where you guys finding 300 bars refilling from a bottle? Especially from those small ones.
I tried several times to top up my 14L bottles (I believe these are the largest scba we have seen so far) to 300 bars with multiple last push, after an hour cool down max I was reading on the digital gauge about 280 ish. So I gave up pushing my compressor so hard several runs only to get a very last 10%.
Just asking for a friend

 

[manabeknives]

I don't want to be an @rse but where you guys finding 300 bars refilling from a bottle? Especially from those small ones.
I tried several times to top up my 14L bottles (I believe these are the largest scba we have seen so far) to 300 bars with multiple last push, after an hour cool down max I was reading on the digital gauge about 280 ish. So I gave up pushing my compressor so hard several runs only to get a very last 10%.
Just asking for a friend

Getting a fill from a dive shop or a paintbal store, they will fill to 4500 psi.

 

[AlanMcD]

I don't want to be an @rse but where you guys finding 300 bars refilling from a bottle? Especially from those small ones.
I tried several times to top up my 14L bottles (I believe these are the largest scba we have seen so far) to 300 bars with multiple last push, after an hour cool down max I was reading on the digital gauge about 280 ish. So I gave up pushing my compressor so hard several runs only to get a very last 10%.
Just asking for a friend

I refill with a nice slow, cool Shoebox compressor, so I don't lose much of anything on cool down - maybe a few bar, but no more than about 5 or so. So a fill to 4500 psi easily ends up a bit over 300 bar. The first few fills are easily that high out of the 9L, but I used to have the issue you face when all I used was my Joe B Guppy, which I think is a 1.8L or so bottle. That was part of why I added the 9L to the mix . . .

 

[tommyb]

Thanks for the update Tommy
Only to 250 bar....hmmm
Nope...it stays in the box as a costly reminder not to buy gimmicks + i couldn't sell it in good conscious. I think it is junk
Hope the repairs hold out
Mike

Not only that but $150 is a lot of money for a problematic 1st generation device that is having frequent repair issues from our members.

I wonder if Brian is working on an updated more reliable EzAy fill 2 to replace the first generation. Even if so, I would not pay another $150.

I will report back on this thread once I get the replacement and see how it goes.

Honestly, for some owners like me, I didn’t use it above 250 BAR max fills. I personally can attest that my dive shop fill intervals were longer using the device. I could physically look at my GW tank pressure gauge and easily assess if I was conserving air based on 8-10, or more top off from 175 BAR as an example.

It makes sense if you only bleed once vs 8-10 times during a session that a user must be saving some air from which is in the hose.

But, I understand your frustration and only hope the new one works better.

I’m not holding my breath.