Search
Search titles only
By:
Search titles only
By:
Home
Forums
New posts
Forum list
Search forums
Leaderboards
Calendar
New events
Members
Find Members
Notable Members
Current visitors
Resources
How to Airgun Stuff
How to Navigate Site
Calculators
Rules & Terms
Classified Rules
Avoid Classified Scams
Log in
Register
Search
Search titles only
By:
Search titles only
By:
More options
Toggle width
Share this page
Share this page
Share
Facebook
Twitter
Reddit
Pinterest
Tumblr
WhatsApp
Email
Share
Link
How to upload videos
Help
Menu
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
RoosterCogburn's latest activity
RoosterCogburn
replied to the thread
Pellet or slug? Overkill or ethical?
.
So does wind resistance. shooting a 15gr slug with a bc of .078+ is a lot easier to put on target than a 16.2gr pellet at the same...
Jun 10, 2025
RoosterCogburn
reacted to
Cantona256's post
in the thread
Pellet or slug? Overkill or ethical?
with
Like
.
Expansion matters!!
Jun 10, 2025
RoosterCogburn
reacted to
Cantona256's post
in the thread
Pellet or slug? Overkill or ethical?
with
Like
.
Only if you don’t take expansion into account.. I get a lot more pass throughs with pellets than slugs. That’s FPE left on the table.
Jun 10, 2025
RoosterCogburn
replied to the thread
Snowpeak
Artemis P15 5.5mm - location of hammer spring adjustment screw
.
I had one that was either steel or aluminum and one that was brass.. i never had a plastic one in the base 35.. I wouldn't be shocked...
Jun 10, 2025
RoosterCogburn
replied to the thread
FX
FX Wildcat MK3 leak (cannot be filled anymore)
.
i thought so. I honestly felt stupid for a minute, like i lost my mind. Try it in B
Jun 10, 2025
RoosterCogburn
replied to the thread
FX
FX Wildcat MK3 leak (cannot be filled anymore)
.
it's like the valve is being held open.
Jun 9, 2025
RoosterCogburn
replied to the thread
Snowpeak
Artemis P15 5.5mm - location of hammer spring adjustment screw
.
The p15 is like p35, you only stand to start losing power after 150b you're out of HS quickly, so you're basically just barely opening...
Jun 9, 2025
RoosterCogburn
reacted to
hgg2k's post
in the thread
FX
FX Wildcat MK3 leak (cannot be filled anymore)
with
Like
.
To test the theory, I resurfaced the Delrin edge with a slight taper and a rounded edge from 1000 grit to 5000 grit. I also polished...
Jun 9, 2025
RoosterCogburn
replied to the thread
FX
FX Wildcat MK3 leak (cannot be filled anymore)
.
the seat looks very good. the delrin might be a pain, but i hope it works. It's a brutal process to disassemble, reassemble, fill and...
Jun 9, 2025
RoosterCogburn
replied to the thread
FX
FX Wildcat MK3 leak (cannot be filled anymore)
.
it is the delrin being compressed against the metal of the seat by the valve spring + Air pressure.
Jun 9, 2025
RoosterCogburn
replied to the thread
FX
FX Wildcat MK3 leak (cannot be filled anymore)
.
Had to watch several times and play every slow. New valve seal.
Jun 9, 2025
RoosterCogburn
replied to the thread
FX
FX Wildcat MK3 leak (cannot be filled anymore)
.
A valve seal is a valve seal. Delrin buts up against the seat, forms a seal. My mistake. I’ve not had an fx gun for a while and forgot...
Jun 9, 2025
RoosterCogburn
replied to the thread
FX
FX Wildcat MK3 leak (cannot be filled anymore)
.
Somewhere air is passing through without the hammer resting against the valve pin. There is one passage way for Air to reach the barrel...
Jun 9, 2025
RoosterCogburn
replied to the thread
FX
FX Wildcat MK3 leak (cannot be filled anymore)
.
This tiny divot caused a total blowout on a snow peak I used to have.
Jun 9, 2025
RoosterCogburn
replied to the thread
FX
FX Wildcat MK3 leak (cannot be filled anymore)
.
Jun 9, 2025
Top
Bottom
Back
Home
Forums
Resources
Menu