What pistol did you shoot today
- Thread starter Septicdeath
- Start date
I wasn’t sure what I wanted to shoot today…it was getting dark after my chores..so I went to the rack to pick one…I had about 10 of them that I was testing for air leaks for 3weeks now…I went right to my favorite gun hoping it held air …My MK1 with iron sights still had a full charge…10 meters is no challenge for this one so ..took aim at the 25 yards @ 4 “ plates…I switched over to 23 grain Apollo slugs..shot offhand in the dark and hit 3 out 5….I don‘t have a chronograph but this gun hits hard…it’s a crusher…
Upvote 0
I got this FWB 100 running and boy do I like shooting it. I like my Daisy's, especially now that I have both LH and RH versions of both 717 and 777. But this FWB 100 is even more fun than my Rink gripped 46M. I must have taken this apart 10X to get it to run, even after resealing it. It is humming well now. It cost me to the door about 475.00 and then I had to get the reseal kit from Canada. So total about 525.00 into this FWB 100.
Upvote 0
Took the THEOBEN FT Pistol out to get a final sight in done and play a bit with altering my hold technique to suit the new stock fitted.
Damn does she shoot !!! nearly hole in hole at 35Y if I'm doing my job
Damn does she shoot !!! nearly hole in hole at 35Y if I'm doing my job
Upvote 0
Finally got to do a little sighting in.
Well guy's I think I got a good one.
I did the first 5 shot group off hand , and then put 3 through same hole where it's marked 4.
Well guy's I think I got a good one.
I did the first 5 shot group off hand , and then put 3 through same hole where it's marked 4.
Upvote 0
Shooting my new Reximex RPA .177 with red dot. 30 ft standing two handhold. Very happy so far.
Upvote 0
Almost done with the parts gun project …Crosman 38 T/C…just waiting on a roller…it was the sear spring that I couldn’t find anywhere…so I found a spring manufacturer and tried to get one close enough …actual found the right size ….125 x .500…10 coils….010 wire…but it was made with music wire…I went a little more beefy with a .016 stainless wire…I bought 30 springs…it is a very close fit on the guide pin now..the guide pin needs a small 45 degree angle on the end to allow the spring to move freely..and one drop of oil..it now has a little bit more tension now ..doesn’t seem to effect the trigger pull at all to me..so for those who have lost this spring while doing a rebuild not to worry they will be available
Upvote 0
I have one myself..it is the one and done pistol…I call mine the Rattler..it was built for killing farm rats at night…this trick shot was @ 25 yards ..13 consecutive shots…look me up for more trick shots…I even shot tic-tacs and hit paper…lol…the other was 64 shots in a row
Upvote 0
Ol'hatsan 25sc went flat a couple of years ago and hee hawing around on spring it or rechargd it i finly stoped procrastinating and against my better judgement towed in to the dark side and ordered a pcp pump. After the order i did 100 hail mary and scared my body 
So got it going. And charged it to 650fps with gamo premier hollow point . Let it sit overnight and just tested it out a few minutes ago
10m outdoor, first 5 , 2ed cup of coffee, gphp.177
I dont feel that bad for it or me not being shot in a couple of years first crack..
After a brunch break i put in a few more .
Sadly one got away , but overall not bad
So got it going. And charged it to 650fps with gamo premier hollow point . Let it sit overnight and just tested it out a few minutes ago
10m outdoor, first 5 , 2ed cup of coffee, gphp.177
I dont feel that bad for it or me not being shot in a couple of years first crack..
After a brunch break i put in a few more .
Sadly one got away , but overall not bad
Last edited:
Upvote 0
beautiful job !Took the THEOBEN FT Pistol out to get a final sight in done and play a bit with altering my hold technique to suit the new stock fitted.
Damn does she shoot !!! nearly hole in hole at 35Y if I'm doing my job
View attachment 593030
Upvote 0
I'm going out to shoot Mosquito's; Unfortunately it will be with a sprayer , but still air powdered.
Upvote 0
Today I'm shooting the Crosman 1322 with Mellon Air 14" barrel and front site, hinge pin from mag, long barrel collar from Alchemy air. Next will put the 18" barrel from Alchemy to try. 
Upvote 0
Upvote 0
Hi guy’s it’s a beautiful day here in the Northeastern corner US…I Love 
all this High Tec…Precision Made…Exotic ..One off Builds..and ”Expensive “..Pistol’s I see here on AirNation…But it makes me “Wonder” sometimes when you can take a $10 dollar Daisy 
Power line 1200…fiddle around with it and get results like this…Question ??…is it really the ”Gun”
all this High Tec…Precision Made…Exotic ..One off Builds..and ”Expensive “..Pistol’s I see here on AirNation…But it makes me “Wonder” sometimes when you can take a $10 dollar Daisy Power line 1200…fiddle around with it and get results like this…Question ??…is it really the ”Gun”Upvote 0
I’m always amazed at what 2240 can do. With a slightly extended barrel it delivers as much punch as my HW45, and with better accuracy. And that doesn’t mention the legion of options made for it
Upvote 0
Great shooting i see , even with dirty glassesHi guy’s it’s a beautiful day here in the Northeastern corner US…I Love
View attachment 593350
All my targets are 50 feet or more. (16 yards ) out to 40 yards , no my 717 or 777 will not hit anything at 40 but at 50 feet they are super .
Upvote 0
That’s what I was saying..that design breech has been around since the 60’s and it is still used in today’s pistol‘s
with a little more refinement…it was first used on a Crosman 160..I own 2 of them..with a adjustable trigger that is equal to today’s FX gunsUpvote 0