What pistol did you shoot today
- Thread starter Septicdeath
- Start date
I wasn’t sure what I wanted to shoot today…it was getting dark after my chores..so I went to the rack to pick one…I had about 10 of them that I was testing for air leaks for 3weeks now…I went right to my favorite gun hoping it held air …My MK1 with iron sights still had a full charge…10 meters is no challenge for this one so ..took aim at the 25 yards @ 4 “ plates…I switched over to 23 grain Apollo slugs..shot offhand in the dark and hit 3 out 5….I don‘t have a chronograph but this gun hits hard…it’s a crusher…
Upvote 0
I got this FWB 100 running and boy do I like shooting it. I like my Daisy's, especially now that I have both LH and RH versions of both 717 and 777. But this FWB 100 is even more fun than my Rink gripped 46M. I must have taken this apart 10X to get it to run, even after resealing it. It is humming well now. It cost me to the door about 475.00 and then I had to get the reseal kit from Canada. So total about 525.00 into this FWB 100.
Upvote 0
Took the THEOBEN FT Pistol out to get a final sight in done and play a bit with altering my hold technique to suit the new stock fitted.
Damn does she shoot !!! nearly hole in hole at 35Y if I'm doing my job
Damn does she shoot !!! nearly hole in hole at 35Y if I'm doing my job
Upvote 0
Finally got to do a little sighting in.
Well guy's I think I got a good one.
I did the first 5 shot group off hand , and then put 3 through same hole where it's marked 4.
Well guy's I think I got a good one.
I did the first 5 shot group off hand , and then put 3 through same hole where it's marked 4.
Upvote 0
Shooting my new Reximex RPA .177 with red dot. 30 ft standing two handhold. Very happy so far.
Upvote 0
Almost done with the parts gun project …Crosman 38 T/C…just waiting on a roller…it was the sear spring that I couldn’t find anywhere…so I found a spring manufacturer and tried to get one close enough …actual found the right size ….125 x .500…10 coils….010 wire…but it was made with music wire…I went a little more beefy with a .016 stainless wire…I bought 30 springs…it is a very close fit on the guide pin now..the guide pin needs a small 45 degree angle on the end to allow the spring to move freely..and one drop of oil..it now has a little bit more tension now ..doesn’t seem to effect the trigger pull at all to me..so for those who have lost this spring while doing a rebuild not to worry they will be available
Upvote 0
I have one myself..it is the one and done pistol…I call mine the Rattler..it was built for killing farm rats at night…this trick shot was @ 25 yards ..13 consecutive shots…look me up for more trick shots…I even shot tic-tacs and hit paper…lol…the other was 64 shots in a row
Upvote 0
Ol'hatsan 25sc went flat a couple of years ago and hee hawing around on spring it or rechargd it i finly stoped procrastinating and against my better judgement towed in to the dark side and ordered a pcp pump. After the order i did 100 hail mary and scared my body 
So got it going. And charged it to 650fps with gamo premier hollow point . Let it sit overnight and just tested it out a few minutes ago
10m outdoor, first 5 , 2ed cup of coffee, gphp.177
I dont feel that bad for it or me not being shot in a couple of years first crack..
After a brunch break i put in a few more .
Sadly one got away , but overall not bad
So got it going. And charged it to 650fps with gamo premier hollow point . Let it sit overnight and just tested it out a few minutes ago
10m outdoor, first 5 , 2ed cup of coffee, gphp.177
I dont feel that bad for it or me not being shot in a couple of years first crack..
After a brunch break i put in a few more .
Sadly one got away , but overall not bad
Last edited:
Upvote 0
beautiful job !Took the THEOBEN FT Pistol out to get a final sight in done and play a bit with altering my hold technique to suit the new stock fitted.
Damn does she shoot !!! nearly hole in hole at 35Y if I'm doing my job
View attachment 593030
Upvote 0
I'm going out to shoot Mosquito's; Unfortunately it will be with a sprayer , but still air powdered.
Upvote 0
Today I'm shooting the Crosman 1322 with Mellon Air 14" barrel and front site, hinge pin from mag, long barrel collar from Alchemy air. Next will put the 18" barrel from Alchemy to try. 
Upvote 0