Taipan Taipan Slash first tuning report.

Jump to latest Follow Reply
MACTEN said:
It doesn't but Tony may soon have a solution.
Click to expand...

SigG posted a couple of messages back that it's pre-threaded. Are you saying Tony may have an adapter soon or that yours is not pre-threaded?

Slash End cap.jpg
 
Upvote 0
Ada
bernieorosz said:
SigG posted a couple of messages back that it's pre-threaded. Are you saying Tony may have an adapter soon or that yours is not pre-threaded?

View attachment 575895
Click to expand...
Adapter is required. It's the same setup my Veteran II's are. None available. Tony should have the solution soon.
As well, it may be real information they copied, but that person is quoting the Wolfeik group website which aren't Taipan.
 
  • Like
Reactions: bernieorosz
Upvote 0
jpiperson2002 said:
One .25 Slash Tactical with the shorter 420mm barrel arrived set at 69fpe using I forget which JSB pellet.
The adjustable power range available via regulator settings in the 420mm barrel appears from specs in web ads to be between ~80J (59fpe) and ~130J (95fpe).

The additional 'power kits' have parts which can be used to increase the top power, or to reduce power down into the 12fpe range.
I'd originally hoped that the Slash could be tuned down by the user into the sub-20fpe range for close target practice, like a K1 and GK1 can.
I won't know the actual lowest power range available in the 420mm barrel without real world testing, but a bottom end of 60fpe would still be hotter than I'd like.

I'd asked Tony @ Talon airguns to set it up in the 50-70fpe range if possible while he was shooting the test target he sends with each new air gun.
If you have one drop-shipped from another vendor it might arrive at any power/regulator setting. It wouldn't matter much how the regulator is set when it arrives though. With a chrony a person could just run the regulator from Min to Max and plot a velocity/power curve for regulator setting and pellet type. A few hour job for sure but just part of the fun of getting a new model.

I haven't checked the relation of the regulator's face plate position to the velocity of a pellet.
Mostly I'd be curious how many rotations it takes to go from the bottom to the top of the available adjustment on the regulator, and whether there is a linear relation in regulator setting to a pellet's velocity. Some airguns can go a dozen+ rotations on the regulator control, though the effect on velocity might drop off after some point. Or else the reg pressure might be set so high that the shot power begins to decrease as the higher pressures prevent the valve from opening properly. I don't know how the new valve on the Slash works but it will be easy enough to see how pressure affects the power curves with a few hundred pellets of testing.

I'm not able to check accuracy, just power curves, and don't have the patience or opportunity to gather a lot of data points for those.

MACTEN is off to a good start and I expect that we'll see some more demo videos as well as people show off their new machinery.

JP
Click to expand...
As for the regulator adjustments. I said earlier it seems 1 degree on the clock = about one bar or just under so lot's of movement available up and down.
 
  • Like
Reactions: bernieorosz
Upvote 0
MACTEN said:
Ada

Adapter is required. It's the same setup my Veteran II's are. None available. Tony should have the solution soon.
As well, it may be real information they copied, but that person is quoting the Wolfeik group website which aren't Taipan.
Click to expand...

Thanks for the clarification.... I'm surprised DonnyFL doesn't already have one available and ready to go :).
 
  • Like
Reactions: MACTEN
Upvote 0
MACTEN said:
They haven't tried yet. Not sure they think too many Vet II's are out there which is the exact same setup on the shroud end.
Click to expand...

Maybe DonnyFL will come up with a 'Reg Dialer' for Slash, similar to his original Taipan Vet 'Speed Dialer' we all used :).

But like you say, there needs to be a good market for him or anyone to produce them.
 
  • Like
Reactions: MACTEN
Upvote 0
You must log in or register to reply here.
Top Bottom
Back
Home
Forums
Resources
Menu