FX Maverick Compact .25 maxing out at 50 fpe (SOLVED)

Jump to latest Follow Reply
HogKiller said:
Yeah, it's a tolerance stack, can't get away from it. Well you can but, I doubt seriously we'd want to pay for it. With modern CNC machines, when properly set up, they should be holding ± .001" .03mm or closer, if they are paying attention.
Click to expand...
Yeah, so that pin is completely missing from my gun.

I can say that performance is better, but still not reaching the supposed 66FPE max, instead is maxing out at about 50-55fpe
 
Upvote 0
sparker said:
I think we can remove that variable from the equation at this point.
Click to expand...
Not from what I've seen, both personally and reading various posts for 1.5 years. If I'd produced some the stuff they had let through, I'd have been fired.
sparker said:
Yeah, so that pin is completely missing from my gun.

I can say that performance is better, but still not reaching the supposed 66FPE max, instead is maxing out at about 50-55fpe
Click to expand...
Freaking SERIOUSLY?????, luckily I think it's possible to put in a new one yourself, if the send it to you, Or just tell FX to go through it and fix the darn thing. Oh Oh there are two different pins, one is 2mm longer than the other. As for the hammer weight, they only list one on the parts list, ditto for the spring. If someone has the .25 hammer weight numbers that'd be cool or I can take mine apart and check it.
 
Upvote 0
HogKiller said:
Not from what I've seen, both personally and reading various posts for 1.5 years. If I'd produced some the stuff they had let through, I'd have been fired.
Click to expand...
I think you missed my sarcasm.
HogKiller said:
Freaking SERIOUSLY?????, luckily I think it's possible to put in a new one yourself, if the send it to you, Or just tell FX to go through it and fix the darn thing. Oh Oh there are two different pins, one is 2mm longer than the other. As for the hammer weight, they only list one on the parts list, ditto for the spring. If someone has the .25 hammer weight numbers that'd be cool or I can take mine apart and check it.
Click to expand...
I’m going to see if they answer the phone tomorrow. If they send me one it’s easy to replace. There’s another thread that had info on the .25 hammer weight, they said the head thickness of the .22 is 4mm .25 is 6mm and .30 is 8mm. Mine measured 4mm, I don’t have a scale handy to weigh it.
 
  • Like
Reactions: HogKiller
Upvote 0
sparker said:
I think you missed my sarcasm.

I’m going to see if they answer the phone tomorrow. If they send me one it’s easy to replace. There’s another thread that had info on the .25 hammer weight, they said the head thickness of the .22 is 4mm .25 is 6mm and .30 is 8mm. Mine measured 4mm, I don’t have a scale handy to weigh it.
Click to expand...
I've been ill, my /s detecter is off line right now. Just for giggles back off your #2 to 120 bar or so, you may have to crank your HSA IN. I believe I'm at 123bar and perking along at 892, 60ftlbs.
 
Upvote 0
HogKiller said:
Freaking SERIOUSLY?????, luckily I think it's possible to put in a new one yourself, if the send it to you,
Click to expand...
So I was completely wrong about this one. The schematic makes it look like the pin goes in the top of the receiver, but it is actually pressed into the bottom of the receiver. The top is just a hole, so if I get the right hammer I should be sorted.
 
Upvote 0
sparker said:
So I was completely wrong about this one. The schematic makes it look like the pin goes in the top of the receiver, but it is actually pressed into the bottom of the receiver. The top is just a hole, so if I get the right hammer I should be sorted.
Click to expand...
In theory, yes. I've torn mine apart so many times I think I can give Ernst Roe a run for his money...kidding....sort of. So, are you missing the pin?
 
Upvote 0
You must log in or register to reply here.
Top Bottom
Back
Home
Forums
Resources
Menu