I normally go around 25 yards, I can see the small groups without needing binos at that range. You'll likely end up with a basic circle as you move the liner to each new position on the "clock". Always using the same hold point, which I failed to mention in my previous post (oops).
I would also not tighten the liner nut too hard in between shots and also at the final location. Tightening too much can stress the liner (similar to what cahil_2 stated).
There are also other posts on this subject if you care to do a search.

mike

hi yes all spring looks fine , ive since tried 3 new valves and seats still can't get it to keep air in any ideas please im really stuck now and Rti don't want to know .

just read a post where 28 FPE was considered low power ! ( with a 10.? grain pellet )

In my experience, Keep feeding them, use cracked corn from tractor supply, do 1 50lb bag a week. They will stick around as long as there's food. They will come out at sun set despending on the season. Heat of summer 8-8:30, winter 5ish.

also for others who might need a fill source, your local paint ball place might be able to accommodate you

100-125 yards is a long way trying to keep a 16gr pellet tight. And why you never see one being shot in a 100 yard BR competition. Lots of guns shoot 16’s fantastic. But at 100 and beyond, Lady Luck is gonna have to play her part.

Iowa Airgunner said:

I am looking for a fill probe for a Lane regulator. It is 1/4 inch X 1 or 6.4X25mm.
Lane Regulators is taking a brake so I can’t order one from his eBay store. And all the probes I see are 6.9mm.

Click to expand...

I'll try to remember to measure mine...

Veteran.

Ground Squirrels in the spring.

rc4fun said:

This is the paper that Ernest uses in his video on polishing washers.
Zona 37-948 3M Wet/Dry Polishing Paper, 8-1/2-Inch X 11-Inch, Assortment Pack One Each 1, 2, 3, 9, 15, and 30 Micron https://a.co/d/fvkPGzK
Do not use silicone on the washers. Don't over do the oil.

Click to expand...

Thank you @rc4fun
The link did not work but I found the Zona paper on Amazin'
Edward

beerthief said:

HMMM? the new squirrel meat .

Maybe Feed the homeless campaign , cooked and canned "the new Spam" ?

Click to expand...

They already eat iguanas, can' tell you how many iguanas you can see on the road ran over.

JoePolanco said:

I achieved something yesterday that I've never achieved before. Today with the RTI Mora .25 cal I posted three exceptional (for me) targets. I need to say these were all shot indoors so it's not something that I would expect in a real world scenario. However, I've never shot scores this high before at 50 yds.

This .25 caliber 700mm Mora / AEA 29.5 grain pellet combo, shooting at 975 fps, is absolutely spot on.

Two targets using the AEA 29.5s shooting at 975fps and one using the AEA 33.9 shooting at 935fps. There difference is demonstrable.

View attachment 555383

View attachment 555384

View attachment 555385

Click to expand...

Can't wait to shoot mine. Nice shooting

airgunutty said:

By clipping the spring wouldn't it also be lowering the fps? Don't really want that. Also if I did clip and didn't like the change can't unclip that spring. A new spring is half the cost of a new gun.

Anyway I'm not trying to discard your suggestion as to a possible improvement only saying that I don't think it's one for my particular needs. I do thank you for taking the time to read and to share your thoughts.

Click to expand...

Yep, clipping coils off a spring would reduce power. From my experience, the change is usually in the 5%-10% ballpark per coil. If you want to tame recoil, reducing power is usually required. Glad that you're happy with how the gun is shooing.
R

JP806TX said:

I wish I had your skills.
For me, I added about a pound of lead weight to the rear of my TX today. It seems to "sit" a bit better when I'm in my field target position. Accuracy wise and recoil wise...???

I guess I'll find out this Easter Sunday when I shoot against other PCP shooters.

Click to expand...

Good luck at your competition on Sunday. May all of your lead find it's intended targets

Boerne Shooting Club
33 Shooting Club Rd
Boerne, TX
10:00 am start
gate open at 8:00
$20
1 -3 target match

AGR
Thank you sir for the quick response, much appreciated! I will be forwarding your response to my buddy so he can follow up on this.

Again thank you.
Bell well, stay safe

Mike

Airgunner’s of Arizona 50 yard bench rest match at Ben Avery shooting range. April 15, 2025.
1300 to 1600 time
See website for specific rules

The wind was a bit challenging at time. Great course layout, just like you would expect from PSA. A big thank you to all that put this together!

I have yet to run into a problem removing the barrels on my K1s. I scribe indexing marks on the barrel and receiver.

Noisy?
Not any louder than the compressor.

manabeknives said:

Thanks for all the Photographs
Looks like everyone had fun
How did the flags work out for you?

Click to expand...

Flag worked good. It is a little bit to tall. Easy fix. Nownto make 3 more.

Thats great shooting the brococks are great guns
had one and traded it should of kept it

My 600mm came in a 1:22 twist - I think that was standard and 1:16 was the heavy a few years ago. UA shows 1:16 as heavy and 1:40 as standard currently, but I have seen 1:37 too. My 1:22 shoots 44gr pellets and hybrids very well. The Javelin and H&N 50gr are good too. The 43gr Nielsen and 45gr Zan are terrible but heavier ones shoot fine.

MDriskill said:

FWB themselves made spacers for their standard buttplate, they are typically 10mm thick. Just one of those will get a Junior stock pretty close to a standard one.

Click to expand...

I had two spacers on my 300S.
Now I I have two on my 601 which I took off of the 300S..

darknes said:

Well the stock already exists for FX Panthera/Dynamic for 480cc bottle and 300 bar. I already have it on my Fx panthera
View attachment 555712
As for the power plenum, if you want it that huge, try to see if the cartridge from the Fx Drs fits, my guess is it might.

Click to expand...

I can't complain about Air-G-Tac.com accessories. Tomorrow I'll have the front reducer coming and I'll have another bottle as well as the lower arch rail. For myself, I can only recommend it. Pictured here is my son's Pantheon. Mine is the Kalibrgun Snipe II in the photo a bit in the back. I have both in cal.22.

What I know if something doesn't suit you (expensive shipping to your country,etc) just contact them and they can always find an individual solution.
I'm for example wanted a gauge cover without the logo, so they sent me what was ready for their owner. That's what I call a human approach.