I'll run several CO2 cartridges through it and then decide what to do if anything. Thanks for the info supplied.

Always fill slowly, bleed quickly. One of the pcp "commandments". What compressor?

3rd time was a charm
thanks for the help

marflow 777 said:

there more than like only less than 10% of the members here and far less that are not member that have the tools or skills to replace a spring no less do the complete job
now some just what an idea or be able to read some others thoughts

i have always thought that helping people was a good thing and if you do not what to just walk by and that is what you should have done here

Click to expand...

Agreed. I forget that not everyone can work on these things. Apologies

The upper end Hawke's are a really great scope for the money.

Is anyone privy to the info needed to date the manufacture date of a FX wireless chorny?

tim

1/2- 20 or m18 threads

FLgunner said:

Did you cock it before filling? If not Cock it and try again. If there is no air in the cylinder and the hammer is forward it could be putting pressure on the valve and holding it open enough for air to leak out the barrel. By cocking it, you are removing any chance the hammer could be holding the valve open.

Click to expand...

Yes I have cocked it all the way back and it is still letting air out when I pump but thanks for the response.

Nice cond. $125 TRD>([email protected]) Willy

This listing has been renewed

Gentlemen, the forum community has answered the question that was posed, and y'all showed great restraint in your responses.

Thank you all for taking a stand to protect the Air Powered Shooting Sports by taking care of the question on the lowest level possible, peer-to-peer. The united front of Airgun Nation members giving a unanimous and firm "NO!" reflects well on the membership.

Thread locked and will be allowed to remain as a reference of your collective good character.

scubajeeper said:

I’ve never personally ordered from Krale but my good buddy has several times. He tells me that he gets guns faster from them than some shops here in the states. He’s happy with them.

Click to expand...

I've read that as well!

Great Post!!
Thank You!!

Oldgeorge - I wonder if you may be binding up on the hammer pin. When I reassemble a crosman I like the hammer in the cocked position and the bolt forward, line everything up best I can, open the bolt to install the breech screw (not tight just enough to allow the bolt to close, install hammer spring, rear cap and screws, test for function before tightening all screws. Good luck

Custom made grips to convert the HW75/P2 back to its roots and accept the .45 grip panels. The grip panels are deep hand checkered Rosewood. They are modified so the screws can handle o-rings and stay snug. A problem always plaguing the 45. Also the standard 1911 grip cut outs (magazine release, detent) have been filled and colored. The screws are ground smaller for the o-rings, polished and blued. The extension is made of a very dense hardwood called Jarrah from Australia. Then painted black. It’s drilled to accept the original Target grip screw and a hole for access to the trigger adjustment screw for making fine adjustments with having to remove the grips. I made one for a fellow member here and another along with it. Probably will not make any more. This may also fit the HW45/P1 with the Target grip. Don’t have one check for sure. And I do not remember how the trigger adjustment screw works on the HW45/P1. The kit includes a pair of Rosewood grip panels, extension block, 4 Allen screws and 4 o-rings. GUN NOT INCLUDED!! $75 plus $5 shipping. Continental U.S only.

Emu, thank you for the review from someone who definitely is a field user and hunts A LOT and shoots a lot like Luis above noted! Oneday I hope to get a chance at a javelina/peccary!

Found mine on ePay - listed as, Crosman 22 not working needs seals. Could tell was nicely assembled 2240/50 with older Hy-pac adapter. Turned out 2B a 2250, 177 cal, and HS adj was max in holding the valve open. Still haven’t taken it down for a thorough inspection yet. Planning for it to be a peep sited plinker like yours

Centercut said:

Butt hook for Skout Epoch.

I worked with Andy @NAIAD001 to get a decent butt piece for my Skout so that I could “get it off the bench” and shoot EFT. I sent the factory butt pad and mounting piece to him, and he did an excellent job. Perfect fit. It allows the same adjustments as the factory butt pad. I removed the wing extensions since I like a tight fit on my shoulder. Last photo shows the butt hook with wing extensions.
HIGHLY RECOMMENDED! Great job Andy!!!

Butt hook without wing extensions

View attachment 423051

View attachment 423053

Click to expand...

Can u email me at [email protected] about this butt hook. Thanks

Ok thanks will do

This listing has been renewed

@IndyDurtdigger I was just curious. Not looking to chastise you. I bought my setup under the new owners and got it in about 3 months. The only delay was some miscommunication on one of the base punches. Your experience was your experience and you’re supposed to speak out about it good or bad so that people know. Thanks for letting us know.

Thanks, BB. I don’t really see any reason to adjust mine at this point.

This listing has been renewed

I added an ARCA adapter that mounts under the trigger guard and use a Two Vets 55 Ball Head mounted to a Recon Tripod or a rail we have mounted in our blind. Controls the weight now that the geometry of the mount has changed.

Airgunrevisions.com Spring tune kit Kratos, Akela, Caden .177 or .22 caliber
New in package.$23.00 SHIPPED.