Dr. Kralenstein said:

What does it matter to you if he keeps responding on an open public forum?

Click to expand...

You are absolutely right.I missread into his responses . And who is he to say that it is not a good idea . I to would like to know if a Diana 177 could be drilled and reline with a 22 cal liner. I think it could , and what about the money , most of our hobbies are expensive. There are many members on this forum that might have a more positive impute .Years ago friend had an old 22. Rim fire resleeved. Worked great

OldSpook said:

Porous Moderator Design Tests

Yesterday at this post we started kicking around this idea. So I made one and tested it. Not bad. 😉 Here is the audio, stripped and set up for comparison, three shots bare, three shots unwrapped and three shots wrapped. Here is the graph of that audio. I cut the graph off at 10 kHz. It...

www.airgunnation.com

Click to expand...

Thanks. Been lurking on this forum a while, have read the linked thread.

Give Airguns of Arizona a call. There are Alpha Wolf upgrade stocks available as far as I know. It's pretty much drop in, but there are some extension pieces for the safety.

elwoodblues said:

Froggy's does have a Saf-pak that goes into the block of the chaser and fills to 2400 psi but only gives a dozen shots or so but at a much higher velocity I have one that I'm not using...

Click to expand...

I know modding tuning and tinkering is a lot of fun, but if I was looking for that amount of pressure I would simply go with the Diana Stormrider (unregulated Gen 1) - filled up to 2900 PSI it shoots on 1000fps+. Since the regulated Gen2 is out, the Gen1s are quite cheap. Same for the Diana Bandit (also fits in the Chaser stock with minor adjustements) - and simply use the long barrel of the chaser. A baser. Or a chandit

It looks like you want to exceed your Benjamin Marauder .22 in terms of power

elwoodblues said:

How did you get that barrel on the Notos

Click to expand...

Turn down the breech side to 12mm OD and add a internal groove for pellet probe oring

JOSHUA777 said:

so then lyou dont need a adapter? im new to this ,so still learning. so if you buy the buckrail , you DONT need an adapter? thanks guys for all your awesome advice. cheers!

Click to expand...

No need for a adapter. All you need to do is unscrew the end cap and also remove the shroud bushing. The ldc replaces all of that. It only adds about 4 inches to the length.

Gandalf714 said:

Its cheap plastic. BUT, its very lightweight and strong. Really not that bad. I replaced mine. Its a .22 with pretty much everything possible done to it.

View attachment 423268

Click to expand...

LOVE the "Flying Tigers" sharkmouth. (I'm a WWII aircraft buff)

JOSHUA777 said:

ok so thank you very mcuh. greatly appreciate. so you say it doesnt perform well at lower reg. setting? havent heard that one yet. if so why and what does it do? i havent heard anyone mention this? thank you.

Click to expand...

The regs just aren’t as consistent at super low pressure. To optimally run 14.3 you will need to set it very low. The avenger is just meant to run at a little higher power levels. You can always experiment. Maybe a little higher reg with low hammer will work. It actually did pretty well on the one I had.

Do not advertise or announce an upcoming availability.

Make quality posts that add to the community. Get your requirement of post count and presence THEN post a WANT TO SELL.

This listing has been renewed

It's worth what a buyer is willing to pay for one. Since Jim E from another site is retired from importing them to the USA ; They've become less available. Very few come around for sale. The more desirable models such as ; Running Target, Unlimited models with adjustable comb height and two sets of sights are a very expensive rare bird. I see many posts about these come and many say 550- 650 is a fair price. It really doesn't matter if it's seals are old, that's to be expected. What is to be expected is the seller not being responsible for others . If you want one rebuilt....do it. It's not at all hard. Or pay someone like David Slade to work it to your expectations. But let's not expect the seller to short price himself to benefit the buyer.

1969Nova said:

I'm now 76 yrs. old and it is time to reduce the cocking effort of my .22 RWS 54. This is my starling gun.


I have to be able to cock it while lying prone on the breezeway floor. Velocity is not necessary. Right now I'm getting 764 fps, but only need 500 or so. Heck even 400 fps is plenty for birds at 16 yds.

Who has a decent replacement spring?

And no, I don't want to cut coils, forge & grind new ends, etc.

Click to expand...

I am and old man and my preferred ag is Mr. Mike Melick XS12 .177 with his magic . At 25 yards is very good .

I fill my LP50 with my CF 4500psi SCUBA tank...
Just a use a little Valve control is needed!!
It just take a slight opening of the valve.....just to get the air flowing...
also I don't like to Fast fill my air cylinders/bottles.
So a little Valve Control is all that is needed!

My brother still has the one I had. It's the gun that brought PCP technology to the beer budget shooters. Not fancy, but light, simple and reliable. Like shooting a 10/22, but single shot.

engfred said:

Hehe
Dangerous thread.. it is like religion.
The Electronic rifles beats the mechanical rifles in flexibility. I bougt a Redwolf and fitted a Heliboard because i was tired of tuning my Crown up to heavy slugs shooting long range and back down to 8-10 fpe for garden plinking. I still have my Crown and i know from experience it takes almost an hour to retune and fine tune until i am pleased. My Redwolf i take out of the box select program 3 for shooting light pellets in the garden at 27 yards. Then i go to the shooting range select program 9, 10 or 11 depending of the slug weight. At 1000 fps. If i fill the magz. With knockout slugs. Fit the push on 3d printed turret with range ballistic for Knockouts. I just set the turret for like 88 yards and i am 100% sure i can hit within one click on the first shot‐ without even test shoot or blank shoot. If i put on a chronograph its spot on from first trigger pull. It takes only 5-10 seconds to go from slug rifle to garden plinker. With the low power program for garden shooting i can shoot a full tin of pellets of the full 700 cc bottle. It is both a powerhouse and a gardenfriendly gun that keeps superior accuracy in high and low power. And 12 custom programs to work with ....That is reallyView attachment 423622 flexible or what?
Best regards from Denmark

Click to expand...

Ya now it’s tunable since you added more parts and spent more money on your $2800 gun.

This listing has been renewed

No worries there marflow, i doubt i have a vehicle that could make the trip. I used to do a lot of buying, selling and trading on the old yellow forum and i was always a nervous wreck till things got delivered. Now that there are no more toys that shoot shows in Findlay ohio, that was my no shipping outlet as i'm not far from findlay, I'm back to shipping and puckering up.

This listing has been renewed

Thank you all for the ideas. Now I will have something to feed my Gamo Urban. First ppc

Raider03 said:

This correct. I messed up.

Click to expand...

No biggy. I come from the manifacturing world so we specify diameter and the threads per inch. But a lot of the consumer world will say UNF or UNC without referencing thread per inch. Means the same thing though.

We have fun at our NRL22 matches... and on this channel in general! After the match yesterday we shot a little content piece about some neat little steel walking targets where we put two teams of 1 airgun guy + 1 rimfire guy together to battle it out on the range.

Here is the video:


And here is the link if you're interested in the targets:

POINT BLANK ZERO - cross hair on squirrel = dead squirrel. I generally consider one pellet width high and one low from Point of Aim to be within my Point Blank Zero. Still good information to have. The manual way to determine your dope card is to set up a target and shoot the same hold on different spots, every five yards. Note the clicks (or the hold off) needed to bring it back to zero. That is your hold off for that range. I don't have a problem with the fancy apps, but I do have 100% faith in old fashioned empirical evidence.

So, I started building this rifle back in November. Posted pics and was going to shoot it next day on the chrono. I filled tank to 4100psi and during the night, the cheap chinese regulator blew a burst disk. So I ordered a Ninja high pressure reg from Hajimoto and decided to redo a few things while i waited on it. Heres the final version. I have only shot it to 50 yds thus far. At 2400psi on reg and 1 1/4 turns in on hammerspring it was chronoing at 52 fpe @ 840 fps with JSB 25.39 pellets. It shoots great. Ill post what i have now and then follow up with final results.Going out to the family farm tommorrow to see what she will do. I dont think i'll have any problem getting over 60 fpe from this rifle. I will post results. Its a .22 Avenger that i sent the barrel and action to Ailen Airguns. Wayne ported barrel, increased valve to 7mm and installed 8mm peek poppet. Installed heavy hammerspring and a light valve spring. He removed factory plenum ceiling and installed 25cc plenum. I installed an AESWEDE trigger and shortened carbon fiber shroud with his bottle bands. I installed 700cc carbon fiber bottle with a Ninja high pressure regulator, so the gun is dual regulated. The scope is a Monstrum G2 6-24 x 50 and the tripod is a Talon Tunes carbon fiber custom. The chasis is from Termidator which i painted to my liking and features a folding stock for easy hammerspring adjustment.

I never used this light attachment. Been in a safe for 20 years. Functional with new battery. Have an extra so letting it go. Install a lighted filter between the attachment and scope for a few different lighting options in low light conditions (Red, yellow, or green - Scope and filter not included). Will ship in a USPS small flat rate box for $8.55 CONUS. Buyer pays shipping charges. Paypal FF/Venmo/Walmart2Walmart or PP G&S (+3.3%). Asking $100 + shipping.

wsjones said:

No, that one is different. Look for the A20 one for Disco & Maximus. I added you the oem front to that adapter. The A20 has 2 holes - one in front for the grub screw and one in the rear that's threaded for the Crosman sight screw

Click to expand...

Thanks. I found the A20 and just ordered one.