Nice pic's and story to go with my first cup this AM .

Never mind on the breach o ring with the Barra 1100z guy's. The breach o ring for the Barra 1100z gen 1 is much deeper into the barrel breach than the gen 2. The 1100z gen 2 the breach o ring you can change without removing the barrel. But with the 1100z gen 1 you must remove the barrel to get to the breach o ring beings the gen 1 breach o ring is probably a little less than 1/2 inch deep into the barrel breach. I hope this helps anyone that may need this information later down the road.

Sqwirl57 said:

A friend of mine found this old adjustable riser thingamajig laying around and gave it to me. These things are super convient for just using on random surfaces to get bag height just right.
View attachment 445645

Click to expand...

You can try a Tack Driver bag too, they have different sizes on 3 sides.

SOLD pending payment.

Bought this new a couple weeks ago For my P rod but decided not to use it. Paid $140, asking $100 shipped.

Anyone here making these or know where to pick some up? 25 caliber.

Sniping maverick said:

anyone know if you have a Fx dynamic is any good?

Click to expand...

I like mine in .22 cal/ 700 mm. Very accurate and easier to tune than my Impact. Loves FX Hybrids.

Lobo73 said:

Do. You have the results for the April shoot.

Click to expand...

Here is a link to it.
You can find it under the field target sub-forum

This listing has been renewed

Maybe it was 38 sec with the filter?

If you shoot light weight slugs and a smaller head diameter the standard liner will work. Plus they don’t make a slug liner for our short hunter compacts. I am having good luck with the teds holdover set up on my .22 hunter compact.

Hey guys, here are some goodies that were intended for setups previously listed.

MDT LRA SEND IT - MV3 ELECTRONIC LEVEL

As shown, I have 3 units new in box available.

*** edit as of 3/14/2024 4:27PM PDT ***

3 sold

***

Same as my previous listings, I would like to see these go to fellow enthusiasts! That said, here’s the airgun nation deal:

Asking $125 (each) shipped insured lower 48. PayPal F&F or add fees G&S. Zelle is good too, local pickup in Los Angeles or Orange County.

Again, I want to personally thank the two AGN members who placed their trust in me and look forward to any feedback they may choose to leave after receiving their gear. While we wait for that to drop as early as tomorrow (fingers crossed/no weather delays) please check out my profile on US Audiomart where you can see feedback and evaluate transactional integrity:


Thanks guys!

-Ron

eat your Wheaties

I had a 54 and it loved the aa 16 grain pellets...I could actually group it at 100 yards.

I was surprised to see how slow the psi drops with only a few shots. Took about 10 shots for me to see the psi move on mine. I've had them sit for months without drop but they never make it a few years as I use my 22xx often. You can always pump it and see the pressure differential. The guage do go bad at times but only seen that with being over pressurized.

I have UTG 4-16X44 scope for sale. The scope includes flip scope caps and UTG rings. I had it on an FX which I've sold because I didn't shoot it enough. Used only at a range. $85 shipped insured. Unfortunately I pitched out the box. Zelle or PP-FF. Please see full description below.

I was using today -.25 - 34gr MK2 at 40y and even that close a group will open to a inch with a spread of 18 fps between shoots so at 100y it will certainly be unusable for me.. I changed pellets to the new aea 34gr and my spread whent down to 3 so jsb is definitely taking us by the hair with such a bad product.. how aea managed to have a consistent product and jsb don't....

Leatherman said:

I have mine bedded all the way but you could also have the block bedded and just bed the end of the forearm to support the barrel. This is how a lot of PB rifles with synthetic stocks are made. I think the barrel should be bedded to the stock on the DRS . Just makes the whole platform solid which should help with accuracy . I believe in torqueing the screw to a constant value every time you take the action out and put it back together again. That’s for all guns.

Click to expand...

Thank you, I was thinking the same thing, bed the whole shroud especially because it has only 1 action screw

nla

.22 . She’s all factory stock. She doesn’t get used so she can go. She holds air. Comes with the stock, 3 magazines, Donny adapter, Boyt soft case, Hawke red dot, single shot tray……excellent shape. $375 obo (please be fair) shipped CONUS PAYPAL or Zelle.

View attachment IMG_0003.jpeg

View attachment IMG_0002.jpeg

I could be your neighbor for a while, and I promise I'll take care of whatever you feel the need to give me. I already have a beautiful Regal so we're halfway there. Please keep me in mind, Your new best neighbor...

Want to buy factory RTI Arms logo case made in italy in excellent to like new condition. Hoping someone doesn't user theirs and might part with. Please PM and lets visit.

FreemanS said:

I saw in a review that if you loosen the hinge screw slightly it will fix the wobble making it very solid. It was opined by the reviewer that later versions got fixed being very solid I guess.

Click to expand...

Thanks for that, I'll give it a try.

IMHO, I think you're going to see quite a few BRK Ghosts on Podiums at major events this year. It's a great platform, and they have top shooters competing with them. That's a winning combination.