Anyone know where I can source one?

What u talking about man…
I send all day those H&N exite 7.4gr the cheapest pellet available on pa and they shoot super fine…
yeah with gk1 I just learned to keep the pistol at a certain angle and u will be fine with no pellet sliding into the barrel type issues while turning The mag for refill…

I like my .22's but when a squirrel is a bit out there my .25 is always my go to PCP.
You're needs/wants seem to land you in the .22 realm, but it's like orangeokie said ^
Good luck choosing!

Trucker3573 said:

Best bet is on the west side of the country Utah Airguns. On the east side Cape Fear airguns. Both are authorized warranty repair centers and should be able to get any part you need.

Click to expand...

Capefear all the way.

ImpactX said:

Not sure why everyone buying a impact wants to push it beyond its limits shooting 40gr .22/25 cal slug over 1000 fps. You don't need it. You want it cause you see youtubers doing it. Lol. How about stop trying copy others and just shoot it and enjoy. Are you trying to take down elephant and hippos, is that why you must have a slug gun with all the high power upgrades? Even a stock gun will sling those slugs at 800-900 fps and be just as accurate.

Click to expand...

Hehe, imagine trying to tune .25 M4 slugport/hybrid HUMA probe just to test out JSB Exact kings 25gr with 800mm.. Had to turn reg down to 60bar before saw any effect from slower velocities. Tried to go down to 900fps, it was difficult. xD

Nope. Should be the same. The revere is just the newest model of huntsman.

There were huntsman mk1, mk2, classic, regal. Those are all bolt action design.

The revere is the newest with side lever. Owning both, I recommend you go with the revere.

Winner shot an Mrod, eh? Congratulations on your excellent marksmanship.

Schéma Umarex Hammer.50cal. Dobrý den, koupil jsem si Umarex Hammer .50
> cal vzduchovka od airgundepot.zendesk.com před dvěma týdny. Bohužel,
> Kolem kazety mi uniká vzduch. Služba v Evropě napraví
> moje vzduchovka, ale potřebuje schéma Umarex Hammer.50 cal. Schéma.
> Prosím, hodně mi pomozte. Společnost v České republice Colosus bude
> mi to oprav, ale ne bez diagramu. Rozvrh vzduchovky. Nemůžu
> pošlete vzduchovku do USA. Stojí to spoustu dolarů. Můžete poslat
> mi schéma e-mailem. Děkuji moc. Prosím pomozte. S pozdravem
> Macura Juraj
[email protected]

Yeah, well how do I get the photo imported from my forum PM to this thread?

I like to have 2moa and 4moa targets.

MikeVV said:

Same with the Ghost.
But, it's a pretty simple task, to just cut the handle/tube in half, and bolt it back together.

Or -
Like I did to my XR, NO cutting involved !
View attachment 482951

Mike

Click to expand...

My plan is to take it off, chuck it up in the drill press and cut off and then radius the bottom. Do the English (Brocock) have tiny little hands? lol.

uladz said:

That's cool! Airforce should have released a new model with factory pic rail instead of dove. Great work!

Click to expand...

Yes, it seems pretty ridiculous.

the "splits" shot timer app for android has picked up my sig virtus very very well.

i use it to shoot steel challenge style shooting.

free is good lol

Ya the glue is always the strong part. It is machined on the inside. I am getting a better gun case

Nealgl1985 said:

If both were shooting the same slug at the same speed would the accuracy be the same?

Click to expand...

At the same medium/short distance with light slugs, the short barrel more likely to have an accuracy edge.

For long distance, with heavy slugs at high velocity, the short barrel will have a more violent shot cycle, which can affect your accuracy. The longer barrel can do the same velocity with lower pressure and a lighter hammer strike.

DonR said:

Good that Mike was able to fix you up. You might want to reverse the cam cover to its original position so it hides the bolt lug and helps keep dirt out.

Don R.

Click to expand...

Good point! The cam cover was in this position when got the rifle, didn’t know it should be vice versa. Thank you!!!

sb327 said:

It is a bit confusing because when designating a tank size in liters, the true volume of the tank is used (how much liquid it can hold).

When designating in cubic feet, it’s how much air AT ATMOSPHERIC PRESSURE the tank will hold.

In liters, pressure is not accounted for in the designation.

Hth,
Dave

Click to expand...

6.75L or 412 cubic inches.

-Matt

kaylaindy said:

Hey guys. My new M4 was barely cocking and then about 20 shot in it stopped cocking all together. How would I fix that? Settings are as it came out of the box. Pictured below. Shooting 18.1 at 890 FPS. Not great groups at 38 yards with JSB and FX. Was about to try AEA but won't cock now. (also see mystery screw I found on Patio a few posts down).

View attachment 482568View attachment 482570View attachment 482569

Click to expand...

Mine doing same thing it's just springing forward won't cock to even load a pellet and I paid $35 for a custom tune from Utah Airguns for the 25.39 grain Hades monsters hammer was on 5 and 115 reg when i got it why wouldn't they notice the cocking problem when they Tuned it. It did it first time cocking it and still doing it calling them tomorrow

The rules is the rules is the rules

OP requested this thread closed.

Bear-of-Grayling said:

Barrel bands finally got here. Shipped from Germany. Made the front sight replacement shroud from a .89 plumbing fixture. Did the pistol and rifle both. Looks cleaner without the sights to me.View attachment 483026View attachment 483027

Click to expand...

I like those barrel bands , I also bought 2 and one stormrider/cr600w/ aluminum receivers with walnut grip and M4 stock adapter. really nice stuff.

We hate to cancel the match, but weather and low turnout coupled with shooters not registering online has forced us to.

Croxton63 said:

she’d insist I sit down for a cup of tea with her

Click to expand...

Well of course.
I have now gotten several invitations to get coffee at other elderly people living where my mother do, i have kindly turned those down CUZ i only drink 1 cup in the morning.
But it is only 2 days ago since i offered one of the little old ladies a ride home with her shopping, but she preferred to walk in the nice weather, which i also understand and after all it is just a few 100 M of walking.

Treefrog said:

I'm with you, John.

Some of the things I love about airguns are...

They're easy to diagnose. No electronics needed. Has seals and leaks. Okay...
You don't need a lift or to pull the wheels off.
You can fix them while seated or standing (instead of laying flat on your back on a creeper).
The're not loaded with sensors that usually give you bad data because of wear in the wiring.
They don't have wiring (and if they do then I ain't buying one).
You don't have to subscribe to a service just to figure out what's wrong.
They don't have to be and stay EPA compliant (yet).
You don't have to mortgage your soul to Mac or Snap-On for the tools to repair them.
I'm my only disgruntled customer.

Good luck,

J~

Click to expand...

Jeff,

All your points are well stated no doubt. Your comments speaks volumes about the journey you go on when wrenching for so long. I grew up with the 3 rules of spark, air or fuel as the main culprits. While I love what electronics have done to improve our on the road experience they sure have added layer upon layer of techno babble just to get er' done now a days.

I can see from both using and from the exploded diagrams that the crosman 2250 platform is simple and straight forward. I have tuned many a TX200 and HW97 and also built the obligatory RWS 850 bottle gun conversion. Even made my own simple reg tester for that project. Then I drifted into the dark side if you will of pcps and while it was a fun ride I yern for the simpler days of the magic feeling I got from my first ever Mountain Air custom guns.

I haven't shot for over 2 years so I am refreshed and renewed if you will. Very excited to get back into the hobby. It could be due to a recent trade I made of a pencil, a single die and a AR for a 86 F250 with a transplanted 7.3 International IDI. Pure mechanical diesel with none of the tech you get with a truck today. I can see it now me loading up the freshly resealed MA 1750, MA 2050, MA 2250 and the MA 2550 in Iddy and driving to the lake for some afternoon co2 plinking . Brings a smile to my face for the simplicity of it all..... Stay tuned.

~GOD BLESS~

john