It has a 7.5 on one side and 5k on the other. The 5k burst the 7.5 was fine

You want to get something a phone call is the right way, my two pennies.

Tacompton Matt said:

I always look forward to the results.

Click to expand...

Thanks Matt, I'm kinda dragging my feet updating this page hoping to implement the new score tracking software. Its getting closer. In the mean time I'll fix the N50 site today

shambozzie said:

@jgreen , very nice compact setup. How does the air stripper effect the gun? With or without effects would be fine. Thanks in advance.

Click to expand...

I wish I could have awesome effects. Thanks for the compliment. The stripper takes the pop away and makes it sound like sasquatch sneezing in the forest, approximately.

tstrever said:

few more pics

View attachment 475304

Click to expand...

Yikes !!!

Scotty1. Yes I’ve had great results with these 48.8 Gr slugs.. Been running them around 880 fps.The video was at 50 yrds in real time too.. I shot them at 100 yrds but don’t have any video I will say this 100 yds wasn’t near as tight.. Shooting Skout 35”barrel on a bench… Good luck let me know what you are shooting those slugs..

Lonakini

ChickenDumpling said:

"Remember, an AN member's strength flows from the Airgun. But beware. Anger, fear, aggression. The dark side are they. Once you start down the dark path, forever will it dominate your destiny."

Welcome!

Click to expand...

Just a thought, since you guys are getting hammer inconsistencies at lower settings you should probably check your hammers finish and clean off any liquid lube. I run all my hammers dry, with a touch of graphite and I can shoot in the heat or the freezing cold and my settings don't fluctuate.

Does anyone know the sizes of all the o rings in the Jet11 25 call ?

View attachment HATSAN-JET2-diagram.pdf

Yes. One is an allen to remove the pressure, the reg itself is still leaking after the new o ring.

MikeVV said:

Ha...you're kidding...right ?
1/18 scale RC cars maybe. 1/10 (or larger) RC or especially full sized cars MUCH money !!!
I'm working on a street legal drag racer. parts are "NOT"...cheap. A quality "race" oriented carburetor, $900+ dollars.

So yeah, stick with your "small"...RC cars.

Mike

Click to expand...

Small RC? Mine is 4 feet long and has a 1 mile + control range with live video feed from 3 cameras (can move them L/R and zoom up to 30X) and a Fog Horn, 6mm Full Auto M4...all controled from the remote. 1.2 GHZ video feed with long range remote stuff (forgot which one). Send the Mavic 3 up with a repeater, or an RC plane on auto pilot for unlimited control ranger. Oh yeah, Night Vision too with 2 IR torches.

Thanks for the match report Scott, I'm bummed I missed it

wgd said:

Thank you, its stunning. In my defense I didn't know there was an HW55T. So I went down an HW55 rat hole researching it, you hit the lottery my friend.

Click to expand...

Be careful going down the "discontinued springer" rabbit hole. It runs deep and you may find you want them all

@bchannell That's a keeper. I think mine was my second or third PCP and we have a history. I initially bought it as a gift for my dad and he didn't want it. I've seen a couple .25s for sale. Haven't seen any HRs in .22 caliber.

Mycapt65 said:

Glided how?

Click to expand...

The way that I do it is like the TX200/PS method. Machine a small groove in the rear of the piston and install a Teflon ring that fits the compression tube.

shambozzie said:

What fill pressure?

Click to expand...

sorry see above, still getting used to blogging, it is stored at 4000 psi

I think that they are great guns. Buy it. Shoot it. Love it.

Good stuff Keith and everyone. Thanks for a great match. Let's do it again!

SpiralGroove said:

When I owned a few HW77’s and HW97, a polished the sliding chamber and then buttoned it with ARH “old school buttons”. I placed them where they couldn’t be seen, they acted as a buffer to keep the metal parts away from each other.

Click to expand...

Good idea. Thanks for the tip.

That is what I suspected. I have the same bag too.

airgunmike56 said:

Well that sucks, Anyone else make them?
Mike

Click to expand...

Oh no, I was asking if they won't. I'm sure they could or would. The video of the guys that made it are from argentina.

I asked Lodewyk to mil a chassis and knock the chips off and send it. He did a little more than that. He took any flash off and gave it a good sanding and partial buffing. I love the raw look. Even better with machine marks. It’s the mark of the tradesman I suppose. There are a few bobbles, and small scuffs, swirl marks in the chassis that won’t be there on the production pieces. The production pieces are cerakoted, FDE and black as of now. But more colors are possible in the future. Is this a prototype? not sure honestly, it could be. I do know it’s probably the only one finished in raw finish. Lodewyk said it was a pain in the butt, so there’s that. The cheek rest is a fitted piece, that can be removed for washing or left off if one would rather. The butt pad is a silicone type material, not sure exactly what it is, but it really stays where you put it on your shoulder. I do consider him a long distance friend, but I’m not afraid to be honest with him either. That said, I paid for this chassis and I offered to give him an amateur review if he didn’t mind my honesty. The guy is legit, and not afraid to stick it out there. I give him that.

I measured the trigger pull on my 28ga, 13lbs.

I'm a couple of months in & I am loving my first PCP. This Notos is incredibly accurate, light weight & for the price you can certainly afford a few nice toys to go along with it. Maple 15ct magazines were my first upgrade, Scope & stock support with M-rail , shooting stick ... I'm like a kid in a candy store !!
Next I'm thinking of a bi-pod & an offset mount to put on a Red Dot for very close up Iguana hunting (within 5 yards) .

PS: Hades or FX Atomic pellets are working spot on for me. Hitting a dime size cluster at 30 yards is a big thrill for me. Off hand is getting better everyday.

I just saw this pistol at pyramid air for $499 with the laminate grips and $429 if you stick with the walnut grips. I was thinking about buying the Hatsan Velox and stumbled across these pistols. They are very nice looking guns.