Air Arms Utah Airguns Pyramyd AIR FX Airguns Daystate Diana Airgun Depot Edgun West Palm Beach Airguns DonnyFL: PCP Air Rifle Shop and Airgun Moderators The Pellet Shop Airforce Airguns
Saber Tactical Optisan Side-Shot Scope Cam NE Airguns Baker Airguns AGS Topgun Airguns Predator International Huben Airguns Huma-Air Shooting Supplies Hurricane Luftvapen AEA Precision Airguns H&N Impulse Air ZAN Projectiles Hawke Optics Stud Mag Loader RX Target Systems Sports Match Scope Mounts Altaros Banner CTA Thomas Air Hatsan USA Georgia Air Guns Skout Airguns Nielsen Specialty Ammo Patch Worm Weihrauch Sport Talon Tunes Airgun-Revisions JTS PARD ST7 PPP RTI AirStryk Industries Macavity Arms

Daystate  Hello, new to forum. Need recommendation for Daystate Huntsman Classic service

enclosing the o rings you require for the Classic overhaul.(pdf file)...if its the same PCP..mine is a 177 FAC..however youll require a special tool to remove the innermost valve (see the attached photo which shows the innermost valve and this tool) which i had to assemble etc myself locally.also attached is the daystate huntsman classic parts diagram

View attachment DAYSTAE HUNSTMAN CLASSIC O RINGS.pdf

20230127_172028.jpg

Attachments

  • part list pcp.pdf
    3 MB · Views: 11

Slugs & Molds - Designing, Making and Testing

Went to the range today... didn't remember to fill up my bottles. Managed to get maybe 50 shots at 250bar. Most of that was sighting and finding the hammer spring balance.

A couple 100yd groups at 800fps. No gud... no gud at all. Will try again... desperately need a booster pump so I can play at 300bar+... open to recommendations.

20240908_113835.jpg

Results  Sagebrush EFT Results

Sagebrush Extreme Field Target Results

July 13th, Pocatello, Idaho

It was hot. We worked for several days setting up the match, then shooting it, then tearing it down. All in the direct sunshine. At 4500 feet elevation, the sun’s rays hurt. In the Northern Rockies, we are more used to hypothermia than heat exhaustion. However, after several flats of bottled water, Sagebrush Extreme Field Target match was done and put away.

Four shooters showed up to shoot.

Was it worth it?

Hell, yes!

I can tell you that it was a privilege to shoot with these gentlemen. Knowledge was shared, encouragement was given, and perseverance was displayed. If anyone thinks shooting sports are trivial, they should have been there.

This was an eighty-shot tournament: a forty-shot extreme field target course, a twenty-shot speed silhouette course, a ten-shot adventure in outer space, and a ten-shot 19th century train robbery.

THE SCORES:

Sagebrush Champion - David Steveson with 62 total hits. 32 in Extreme Field Target (first), 19 in Speed Silhouette (first), 9 in the Alien Attack (first), and 2 in The Great Idaho Train Robbery (bad luck Sundance).

Second Place - Dave Read with 45 total hits. 18 in Extreme Field Target (third), 15 in Speed Silhouette (third), 7 in the Alien Attack (third), and 5 in The Great Idaho Train Robbery (second).

Third Place - Shaun Ward with 45 total hits. 12 in Extreme Field Target. 18 in Speed Silhouette (second), 8 in the Alien Attack (second), and 7 in The Great Idaho Train Robbery (first).

Fourth Place - Ron Gill with 38 total hits. 21 in Extreme Field Target (second). 9 in Speed Silhouette, 5 in the Alien Attack, and 3 in The Great Idaho Train Robbery (third).

Thanks to David Read who built the speed shoot plate racks and the buffalo targets, as well, as the foam board cut outs. Our herd totaled 29 animals.

Thanks to cosponsor Wasatch Airguns who loaned us the field targets to make the match possible. Also, Quality Targets who did a custom run of 2X size buffaloes, and Western Industrial Motor & Machine for their invaluable services.

Ron

Steyr  Steyr Pro X - Question for the Experts

Does the Pro X use choke screws similar to the H5A for lower power levels (e.g. 24 J or 16 J) or is power reduction done through the belleville washers in the regulator only?

I note that the H5A uses a combination of washers in the reg and choke screws to reduce the power level. I can't find anything in the Pro X parts list or parts diagram that references choke screws?

Anyone know for sure?
This Owners manual may (or may not) help answer your questions: https://steyr-sport.com/en/downloads-air-rifles/manuals/65-pro-x/file

.177 M3 Killing it!

Hey dude, what are your reg settings for the 177? Im building a 500mm setup too and want to use the 10g Knock Outs. Looks like it works pretty well for you. :cool:
I’m shooting a 600mm Wildcat mk3 pushing the 10gr knockout at 954fps, my second reg is about 77bar.

Pellet Problems

Know the feeling, never got into reloading and all of that stuff, ADD so I'm afraid I'd blow my face off or something. Of course messing with high pressure air inches from your face is perfectly safe...right? I've found that washing the JSB's in alcohol helps but now I've got an infection from AEA'a....my stash of JSB's is getting lonely, guess I should use them before the expiration date.
We have pellet worms in New Mexico. If you leave a tin more than a few days the worms will chew the skirts off.

I've worked a lot with high pressure cylinders and lines. If the engineering is good and you use as intended its safe. But I always think about how much stored energy there is in a pressure vessel. Knock a half dozen scuba tanks over on a pitching boat and you start thinking about that stuff.

I made a pipe bumper for my FJ40 land cruiser. A piece of 6" seamless steel pipe. Probably 1000psi rated. Capped the ends with 5/16 plate steel and welded it up. Put a gauge and a coupling in it. Pumped it up to 60 psi. Great idea for a little spare air I thought.

Drove around a few months. Never used any air. One day in a tight canyon I snagged the corner of that bumper with a rock. Helluva explosion. Took minutes for the dirt to settle. Blew the weld at the corner and ripped the cap back.

If a high pressure cylinder got away like that no telling how much metal, dirt, rock it would sling. Even blowing an oring at the end of a short high pressure line could sling a hunk of rubber Or dirt in your eye. It darn sure doesn't take much.

Brocock/BRK  Ghost reg issue?

I don't have the rifle in front of me but if memory serves me correctly, the adjustment knob has an Allen head screw attaching the knob to the adjuster screw and needs to be removed to get access to the regulator. Once the knob is removed the reg should have two holes showing for either a pin wrench or snap ring pliers to unscrew it from the body. BRK has a superb video series detailing the procedure.

Cool thank you, I have watched that video a few times unfortunately they already have the knob off and don't make mention of how it comes off. I appreciate the insight to look for an Allen set screw vs my just trying to back it out and then messing up my reg!

Also, not sure why checking the Ghost parts schematic didn't occur to me, found it...
1737784469780.png

N/A  Digital gauges on your reg

Exactly use what you prefer .much prefer digital. Analog can fail all the same. Ordered one of those fancy great wika gauges from Huma. Gauge had a very slight leak. Took me a few weeks to track it down. PIA. All can be problematic and I personally like reading a digital. Creep is there or it isn’t no matter what type of gauge is installed.
  • Like
Reactions: Macros

Huben  GK-1 turned convertible carbine with Corcoran walnut stock

But but, for the same price you could have a silent AF Escape UL in .25, Tammy's old FT rig, maybe a gen 1 gauntlet that actually groups Very well, a modded Maximus and .... .
Hope you can get one, does seem the one actual (except maybe FT) do it all airgun.
Keep us posted when you do get yours.

John
Well that won't be anytime soon. Hope all is well Breaux, hope you don't need to sell them all!

Filter