Threads

Forum list Classifieds

Threads

 Hot Latest activity Questions Social
Air Arms Utah Airguns Pyramyd AIR FX Airguns Daystate Diana Airgun Depot Edgun West Palm Beach Airguns DonnyFL: PCP Air Rifle Shop and Airgun Moderators The Pellet Shop Airforce Airguns
Saber Tactical Optisan Side-Shot Scope Cam NE Airguns Baker Airguns AGS Topgun Airguns Predator International Huben Airguns Huma-Air Shooting Supplies Hurricane Luftvapen AEA Precision Airguns H&N Impulse Air ZAN Projectiles Hawke Optics Stud Mag Loader RX Target Systems Sports Match Scope Mounts Altaros Banner CTA Thomas Air Hatsan USA Georgia Air Guns Skout Airguns Nielsen Specialty Ammo Patch Worm Weihrauch Sport Talon Tunes Airgun-Revisions JTS PARD ST7 PPP RTI AirStryk Industries Macavity Arms

Stoeger .25 Bullshark performance specs

Florida_Man
Airgun-Revisions said:
Yeah all that is going to be the same. Huge difference is the stock being used offhand way nicer. The grip up front allows the gun to be pushed to the shoulder easier and supports the gun better for charging the next round. So offhand shooting I found this design really nice. Especially with a red dot.
Click to expand...
I wish the previous owner of mine didn’t hack the stock up. I had to secure the front with a longer screw and a washer. What little they put back together, the valve spring was backwards. It was an adventure.

They are great bullpups. I’m with JimD and would have bought a Bullshark 25 if they were available when I bought my P35. The rifles are currently swapped stocks.

IMG_6196.jpeg
Click to expand...
  • Like
Reactions: Airgun-Revisions
Upvote 0

About Amazon's Asurion and Compressors

uladz
VneMC2 said:
I initially "invested" spent money on the least expensive compressors that, while adequate for rifle filling always failed in durability when compressing for high volume high pressure applications. I spent more on all the "starter compressors" than it cost to buy a SCUBA rated gasoline powered compressor, sued, from a reputable dive shop supplier in Florida
Click to expand...
Agreed. That’s why I’m saying that I do not advocate for “consumer” behavior, I.e. throwing away stuff instead of fixing. But investing 1000s when you just get into this sport not knowing if would keep it going also not really advisable. But extended warranty with cheap compressor helps a bit as @Air King noted ;).
Click to expand...
  • Like
Reactions: Air King
Upvote 0

Umarex  Umarex Hammer Carbine Accessories

R
ElkhartFarmer said:
Hey guys

New to the forum. I'm strongly considering the .50 Umarex Hammer Carbine since I heard the magazine air release was fixed. My thing now is appearance. The full sized hammer has the smaller bottle and the hand guard, but the carbine doesn't. I'm an AR guy and love a good M-lok rail. I LOVE the FX Impact M3 look with a saber tactical rail, but can't get behind the price.

With the carbine having no hand guard, that area just seems a lil too bare. Any ideas or experience retrofitting a rail like the saber tactical over the barrel? Or even retrofitting the full size hammer's hand guard over the larger bottle on the carbine?
Click to expand...
There is a open box used hammer carbine at Utah Airgun for $850.00 just saw it....
Click to expand...
  • Like
Reactions: Devink
Upvote 0

Best 'barn' pcp's.....?

Dr. Kralenstein
JimD said:
I played with a fpe calculator and I think a ~20 fpe 25 caliber is pretty doable. You could push 25 grain up to about 600 fps and if your gun happened to like 20 grain FTTs you could go almost to 700 fps. Those are not high velocities but are in the same range as the stock tune on my old Prod. Inside 30 yards I think it would work great. Nice big pop on the pigeon but less chance of penetrating the roof. Getting an inexpensive 25 caliber to 50 fpe can be a challenge but tuning it down to 20 fpe should be easy. It would be quieter and use less air. Should be fun to shoot.
Click to expand...
I'm currently making a low power 25 for close range and indoor pest work. Hoping for an accurate shooter at 550 fps with 25 grain pellets.
Click to expand...
Upvote 0

This is a GREAT FORM BUT ?????

uladz
Smitty911 said:
Just bought a 12v/110v off of Vevor for $149.00 shipped. I have two young hengs but this seemed to be cheap insurance and people have had great luck with them. Oh, it came with Alligator Clips for the battery and terminals for the included 110v power supply.

Smitty
Click to expand...
My thinking is the same 👍.
Click to expand...
Upvote 0

Daystate  Is There a Difference Between These Daystate Rifles?

Dr. Kralenstein
Nope. Should be the same. The revere is just the newest model of huntsman.

There were huntsman mk1, mk2, classic, regal. Those are all bolt action design.

The revere is the newest with side lever. Owning both, I recommend you go with the revere.
Click to expand...
  • Like
Reactions: Smitty911, Star7, maxtrouble and 2 others
Upvote 0

Umarex  Umarex hammer air leak

J
Schéma Umarex Hammer.50cal. Dobrý den, koupil jsem si Umarex Hammer .50
> cal vzduchovka od airgundepot.zendesk.com před dvěma týdny. Bohužel,
> Kolem kazety mi uniká vzduch. Služba v Evropě napraví
> moje vzduchovka, ale potřebuje schéma Umarex Hammer.50 cal. Schéma.
> Prosím, hodně mi pomozte. Společnost v České republice Colosus bude
> mi to oprav, ale ne bez diagramu. Rozvrh vzduchovky. Nemůžu
> pošlete vzduchovku do USA. Stojí to spoustu dolarů. Můžete poslat
> mi schéma e-mailem. Děkuji moc. Prosím pomozte. S pozdravem
> Macura Juraj
[email protected]
Click to expand...
Upvote 0

Brocock/BRK  Atomic XR cocking handle too long - hits knuckle

C
MikeVV said:
Same with the Ghost.
But, it's a pretty simple task, to just cut the handle/tube in half, and bolt it back together.

Or -
Like I did to my XR, NO cutting involved !
View attachment 482951

Mike
Click to expand...
My plan is to take it off, chuck it up in the drill press and cut off and then radius the bottom. Do the English (Brocock) have tiny little hands? lol.
Click to expand...
  • Haha
Reactions: Seanbuds
Upvote 0
Load more

Filter

Prefix:
Top Bottom
Back
Home
Forums
Resources
Menu