Hisson said:

Always wanted to try a Maverick but have never had the guts to pull the trigger. I believe the Maverick would be a great platform for a .25 cal slug gun.
Appears to be powerful enough.

Click to expand...

its the cheapest fx airgun with a high ceiling on power ... also the easiest to tune with the "shooting with phil" micrometer ... because i have been thrru the tuning keyhole with the p40, condor, impact m1, m2 & m3 most with the power plenum in 22, 25 & 30 cal, crown, discovery 2ea, pantera, and now the maverick in 25 and 30 cal ... mostly for ground squirrels ... with pellets and slugs ... good luck ... the hpa airgun black hole is deep

PA Cup FT results

PA Cup list of equipment used by each shooter

hope yall enjoy!

Dead-On said:

Well I am no where near buying either one yet. I have to sell a few guns and knives to afford either one right now. So for now I am still researching and looking. With many of my guns, if there is a problem that I can't fix, it gets sent out to any of the airgunsmiths, tuners, and builders. The biggest problems I run into is cost of shipping and replacement parts. So I would assume if there is a problem with the Edgun I could use any of those avenues to remedy the situation.

How about parts? Are they hard to get?

Any common problems with the Leshiey that are going to be a problem that I am not aware of? I've been reading the Edgun Leshiey2 thread a bit and so far it looks like minor fixable problems.

Click to expand...

I do not recommend any Edgun. Nothing but broken promises and no customer support. Steer clear.

I purchased a Leshiy classic from Edgun West about six years ago. Purchased two other barrels, some pellets and a Huma regulator at the time of purchase. Right out of the box I had issues. Rifle was not new, had scratches on it, would not hold air, no extra o rings, all the things unwanted in a new $2000 air rifle.

Brian at Edgun West ghosted me and would not return any of my calls, emails or texts. I had to use the threat of a credit card chargeback to get any kind of support. Ended up returning the damn thing but he would not give a return for the barrels, regulator or pellets. Most vendors will charge a 15% restocking fee or issue a full credit, Brian said fsck off. Horrible vendor. Caveat Emptor.

I'll be there can't wait

AirNGasman said:

Forgive me if I've overlooked something, but how does 7-10 MOA at 20 yards translate to basically the same hole 4 shots at 50 yards? Are you talking about two different guns?

.

Click to expand...

Sorry, I meant to say 100 yards, at 50 yards it’s basically the same hole using the 173 from Mr. hollowpoint. At a 100 yards I’ve gone inch and a half to 2 inches pretty consistently.

ChefSparrowRagazzi said:

Because they don't really do that. Alligator attacks on humans , here in America are very rare. Crocodile, on the other hand, is a completely different story

Click to expand...

Good for them .. but gone anyway but not by me I really don't have the time.. to much work not enough day .

YES,It takes about 5 weeks to get to my Calf. house t Yes, go to their website,I think they are great prices.Yes I have two of the Lefty stocks,lefty yes indeed

New guy here, and thanks to Nikoum for providing the parts and schematics lists, it's much appreciated.

I've recently picked up a Notos, added a couple of cool pieces from Bravo 3D, mounted an Athlon Argos scope and after looking for the biggest bang for the buck pump ended up with a Spritech that did it's job fairly well. Anyway, after the first test firing and zeroing in, I packed everything away and the following day I set up for another session only to find that an o-ring was missing from the quick fill probe that prevented me from getting another session going. I was wondering if anyone here would know the sizes of the o-rings on it, specifically the pair of o-rings that seals that port that delivers air into the carbine's cylinder. When I tried measuring the single o-ring that was remaining with a digital caliper I came up with 7x4x1.5mm but didn't see the probe listed in the parts list Nikoum provided. Any help is greatly appreciated.

orangeokie said:

How do you store spare parts and keep up with which parts belong to which gun? Are you organized?

Click to expand...

I'm not that organized but I do know where everything is at. For spare parts, I place them inside the box the gun came in. O-rings are in separate boxes. I need one of those tray organizers to make it easier to identify.

Firewalker said:

Buzzys is still available on Amazon. I got the yellow tube this spring. I think it's petroleum based?

Click to expand...

I don’t remember. I know many people in the paintball world used it at the time. Although I guess paintball markers operate at a much lower pressure. Might not be good in certain areas of a pcp.

Swfa 16 or 20x rear focus. $300 and done deal .

blkspade99 said:

Ahh ok! Thanks! I just wanted to make sure it wasn't out of the ordinary. I guess it has to move alot because its such a close distance?

Click to expand...

4 clicks is 1" @ 100 yards.

So

4 clicks is 1/4" @ 25 yards

13 yards is about half of 25...

So 4 clicks is about 1/8". Or 32 clicks per inch @ 12.5 yards.

caliusoptimus said:

I looked into changing the spring for a stronger one and...

I already have the (very nearly) strongest possible spring that will fit. A custom spring could get another 5% or so but any more than that and the spring will be pushing into plastic deformation.

That said... a custom hammer might allow a longer travel. Maybe. This could kill two or three birds with one stone... since the stock hammer is soft with a bad surface finish.... might be possible to improve the trigger feel, reduce the hammer wear, and increase power. Hmm...

Click to expand...

There is a lot of space for a heavier hammer. 404 stainless should wear well but it would need a high polish

BayouSelf said:

I bought my first .20 in June, a ‘97 with walnut stock, and I’m a believer. It’s shooting JSB 13.73 around 720fps with a John in PA tune. I’ve owned maybe 6 or 8 .177 spring guns from Weihrauch and Air Arms and have never been able to shoot groups like I have with this one. I absolutely love it.

View attachment 495091

Click to expand...

Smokin specimen...wow man

Dr. Kralenstein said:

Did your last post get deleted as well?

Click to expand...

Yeeeasss. It did.

I'm going to go ahead and read that as, "ok bro, yer a funny guy, knock it off"

They used to be numerous in Anauach and we’d spotlight them in the roadside canals back in 79 and 80 when I was in high school. Of course times were different then and 2 teenagers standing in the back of a truck with a Q-beam and an old school Colt AR and a Marlin .22 while a 3rd drove, would only earn you mosquito bites and maybe an admonishment to be careful from the game warden who wanted to make sure you weren’t shooting deer…

I shoot mine almost always @ 50yd targets; anything closer is no challenge. Crazy-accurate, not hold sensitive, and very powerful.
A beast to cock though. This gun requires a beefy backstop, as it will go thru 1/2" plywood like its not there. I will never sell mine.

The original hollowpoint?

I definitely need a longer barrel and tank. It will turn it into a mini k1.

No problems with my standard Sisewinder in .30. Not too loud with a Huggett Magna. Accuracy is outstanding.

Ive had a chance to do some testing a few barrels. Finaly got to test the .25 SS LW @ 23.82" NO choke
Bore .248
Groove .254
Grooves - 10
twist 17.7"
Stainless @ .71 " OD
I drop shipped this to Martin earlier this year along with a Lilja barrel. Fitment is perfect on both. Wind was mild today but steady.
The only .25 pellets I have on hand are 33.95 jsb mkII & it seems to like em.. all slugs I have on hand didn't make me happy.
I'm shooting them fairly hot as the RAW is set up for .30. I also have a Huma in it.
these are the only 2 groups I shot this afternoon before wind got silly. both at 75 yards. I like 100 but to windy lately for anything serious as usual.
The 1st group was a random shot sighter, then 1 click scope corrected after 2nd, then shot 5 group. The did it again without any correction. I still haven't got the trigger to my liking & will pull action & adjust again.

The full auto system only works well with HPA. In Co2 the gas gets colder and colder and shoots slower and slower. The Drozd unaltered and just juiced up with batteries fit my needs better. Same gun really one with a motorized loader is all. The blackbird would shoot with mags also. I was offerd more than I paid for it so SOLD.

Looking forward to seeing and shooting with the OKC crew !! Hope everyone is doing well !!

EvilHere said:

Thinner mag caps or plates i miss the word my english is a bit bad

Click to expand...

ok, thank you, i get what you meant now.