It's possible that your email address may be part of our Blacklisted words that prevent SPAM. Please DM me with your email address. Spell it phonetically or with spaces so I can see it.

Hobbyman2007 said:

Well that’s some good news. Good work getting her back into shooting form. I can only imagine how frustrated you must have been. On a side note, just watched a YouTube review of the new Theoben rapid in a blue laminate FORM stock. They sure make some nice lumber. I’m not sold on the Theoben name on a rifle with a side lever. Any how ,

Click to expand...

I always wanted a 65, could never afford one.

Then the 500fps law came in and made the 65 into a "restricted weapon" not worth the red-tape to own. I still look and wish though.

Fortunately, I lucked into a deal on a FWB Model 100 SSP ($150) and been happy with that.

AVS is among the softest lead, get a version with large hollow point will give best expansion close to hybrid and RS. Now I don’t know the range your shooting, but if under 40 yards, try polymags for body shots, they will not pass through.

DaMitch said:

What range are you shooting

Click to expand...

45 yards

ZeroVibe said:

Of the things I didn't need to buy today. Thankfully they would only allow me to order one long one. I kept getting an insufficient quantity available when I attempted to order more.

Click to expand...

Yep, that looks like the last one.
Only Short are available.

Gerry52 said:

Did you ask what he did to clear it? I'm curious about that. Customer service is what REALLY makes a business thrive. It's been commented on before how good The Pellet Shop is.

Click to expand...

He used a dowel rod and rubber mallet was able to tap the smashed slug back into the mag enough to get the mag out a and clear barrel didn't have to take anything apart even filled my air back up .I did try the dowel rod but guess I wasn't tapping hard enough plus was using my palm as a mallet.

Capt' Oring sell complete oring kits for the Avenger.

The complete repair kits including poppet and reg for .22 and .25 at now back in stock at PA.

Hey everyone I've been messing with my Beeman. It's my first PCP. I'm an engineer and a tinker so I've taken it apart a few times and made some changes.

I opened up the main valve and made that spring a decent amount weaker. Right now I want to get a little more power. I also added a o ring in the block before the hammer which takes off some for but helps with hammer bounce. Over all I still get 50-60 shots but my curve isn't as flat as it was with the stock valve spring. I also recommend removing the brass washer on the valve spring to make it a little softer. It's STIFF.

My main struggle is that I can't get a reg to work on my model because of where the pressure gauge is. Does anyone know where I could source a gauge block? I would also accept a drop block to add a bottle of anyone can help me source one.


I would also love to find some barrels that fit this receiver. I'm sure a few models work, but I don't know where to buy them.


I've been 3d printing some mods. This one has lasted the longest so far.

But I'm trying some. Resin printer parts too.

Hello Airgun Nation!

We at DonnyFL are currently aware of an account going around impersonating us, saying things like you have one a contest pay a fee OR offering a free DANIEL DEFENSE RIFLE for a small fee. THIS IS A SCAM. We are NOT AFFILIATED WITH FIREARMS in any capacity.

All giveaways are to be ran through our OFFICIAL @ DONNYFL INSTAGRAM PAGE ONLY.

If you have been contacted please report the account and help!

Our official Facebook is linked below along with our Instagram.

https://www.facebook.com/DonnyFLsuppressors

https://www.instagram.com/donnyfl/

Anything else again is a SCAM/IMPERSONATOR

Bimbi said:

Thank you so much. Seems like work out of my current capabilities. I took the valve assembly apart and put it back together, and now even the pufft sound is gone. It's like I'm dry firing it all the time. Something that can give further insight is that when the palette is not loaded and I pull the trigger after cocking there is still a pufft sound. Do you know who can take a look at the pistol for me? Thanks again

Click to expand...

@Bimbi - what is the status of this Steyr ?

Anyone have any experience with the .30 cal LW 28" 1:24 twist barrel in the field yet? Does it do as well with .30 cal pellets as the .22 cal LW 25" 1:15.75 does with .22 cal pellets? What about slugs? I really like the idea of another barrel good with both pellets and slugs. Just wanted to see if anyone has any experience with it yet.

Trying to get ready for the upcoming season for both N50 benchrest with .22 cal and 100 yard benchrest with .30 cal. Just want to hear about a little real-world field results before plunking out the money. Any experience would be greatly appreciated.

I also noticed the new ECR - 30 Cal - 25" SS with 1:24 twist is listed as both pellets and slugs as well. Any experience with this one as well would be welcome.

Thanks for your time to share your thoughts and experiences.

Chuck Bennett

I can tell you from personal and recent experience that not all. The BCM Mod3 does not fit. The slot in the grip is not wide enough to slide over the boss that the grip screw threads into on my Maverick. I have not tried it on my Impact though.
I had bought the grip for my AR but decided to try one on my Maverick.

darknes said:

If the regulator does not hold the set pressure after removing the cylinder then the problem is in the regulator i.e. defective o-rings. So the easiest way to do this is to replace all the o-rings. And then test. Pressurize the entire air rifle to full pressure, let it sit for about 10 minutes, disconnect the bottle. After that, it's best to let it sit for at least 24 hours. The airgun itself should hold plenum pressure for several months.

Click to expand...

Thanks darkness, I’ll test that once I get my cylinder filled up again.

Seems to have a been a proper wind match at Ron's. I hope to make the next one.

3Crows said:

A .20 makes sense in pump and spring but in a PCP? I guess it would be cool.

Click to expand...

Actually, it makes the most sense in pcp... The 13.7s have the highest BC of any offering that is reasonable for sub 20 ft lb service and the 15.89s have the best BC of any offering up to about 35 ft lb... PLUS they just seem to generally be more accurate, or at least as good as my best... Then there are the 18.9 slugs... oh my... they're just wonderful little buggers that will reach out really well but not use a ton of air or cause the rifle to be unpleasant to shoot...
In my stable are Red Wolf and Delta Wolf in 20, plus some Sheridans and a Cros 100 that I converted. Did have a Ghost in the mix but it's out now.
What doesn't make sense to me is having one below 20 ft lb, similar to 22 below 30 ft lb... sure, it will shoot ok, possibly extremely well, but there are better options imho...
Bob

This seemed interesting to me. I’m interested in seeing the FPS and FPE of the .25.

thammer said:

Sounds like there's not enough load on the springs. They get wound pretty tight at assembly so there is enough left at the end of the rotation to still cycle. Maybe try increasing that preload another turn when putting back together.

Click to expand...

Thank you!

Got it, thanks!

Dogowsky said:

Hey man, do you have a source for regulators, orings, and parts for your rainson edge? Let me know and thanks!

Click to expand...

I bought a master O-ring kit from Amazon, they sell both SAE and metrics. This is all I use for my rebuilds and works great. Must be be Buna 70 or higher on the durometer scale.

Screwwork said:

Nice shooting and good grub it should be tasty

Click to expand...

I don't eat them in this area, she went in the trash- she was pg. But do eat deer, elk, game birds and fish.

Tom/TN said:

No …but thanks. I’ve seen and busted enough starling to know how to ID them.

Click to expand...

The app also gives call examples..... That work. Check your local regs on this obviously. Merlin is pretty fun.

That tail looks like you made a mistake..... But if I'm wrong and it's just ruffled I get after crows too. It's weird how ravens and crows will hang out together and ravens will even mourn popped crows. Whatever you hit him with you blew the down out of him

Great shooting and yes, we can be the cause of issues especially with airguns...

TnCnDn said:

What's 40 some bucks, as long as it is the oem barrel band swivel.

Click to expand...

true that

That’s a great solution to your dilemma.