I have acquired an older Condor SS with an Etac regulator and 4500Lbs. bottle that is short and fat. I'm not sure how the previous owner shot this as the bottle placement is in the way of the scope. I have replaced the valve and hat parts but still find speeds that are over 55ft./sec. different shot to shot. Thinking that the regulator is not functioning correctly (any other thoughts?) I am looking for a budget regulator that will accept the 4500 inlet pressure, my earlier valve assembly, and is offset for better shooting comfort. External pressure adjustment would be nice but not required. This Condor also has the early spin on threads - not the SpinLoc upgrade. I'm not opposed to installing the SpinLoc upgrade but I would like to see this Condor perform well before spending serious $ on additional upgrades. What are your thoughts?

Hey does anyone know how to find or fix the regulator for a FX maverick?

Bought a o-ring kit to try and solve the first low shot velocities, wondering what these washers/ o-rings are for.

I recently acquired a Diana 52 in .177 and shot it yesterday for the first time. Brought 3 different pellets with me. I was surprised to find out the Crosman Piranha 10.3 didn't really fit. As a result they actually fired slower than in my Crosman airguns. Anybody have any issues fitting 10+ grain pellets in the Diana 52 .177? Ty

Hi guys, just bought the power block/plenum upgrade kit for my gen1 .30 impact. Has anyone done this upgrade recently? If so, any tips or things to look out for while doing so? Thanks!

Just got my new Tuxing TXED012 compressor today. Spent the morning getting it set up and settled in. I can get more shots per fill now. Before, I would not take more than 20 shots because all I had was a hand pump and I hated spending an hour topping off my rifles. Having that compressor is going to allow me to do a lot more shooting.
I have a question about the temp indicator on top of the compressor. It has no off or on switch, works off of 2 button type batteries, has only one lead ( the wire to the temp sensor ) and the liquid crystal display stays dark. Does it show the temp only after reaching a certain level?
Any advice or guidance would be appreciated.

Looking for the set screw/ball combo that goes inside this port (see photo)

I just bought a compressor on sale and didn't really look at it much but it says on it that you should only fill up too 500cc bottles. Could I fill a 580 or will it over heat and break?

Are there 30mm high scope rings that will attach to the Marauder's dovetail base. Is there a way to put a std. picatinny rail on the Marauder?

Best PCP for squirrels? Looking for a good pest gun

Planning on buying my first pcp. Looking for around a grand with nothing on it. Already bought a compressor. Opinions and thoughts?

I have a FX Maverick 30 caliber sniper with the slug barrel installed. Want to shoot the Patriot javelin 52 grain slugs. What would be the best tune

doesn't work
Beeman sportsman 1000 series ss1000 17mm
I have this old ss1000 thats been sitting around for 20 years
i took it apart and the spring seal is decomposed I can't even tell what it was made of (maybe leather),is there any replacement available?

Kenlh

Hi there! I’m new to this pcp world. I would like to know what’s the little screw attached to the part of the valve going into the tank? Should I tighten it up by hand?(see the picture)

Went ahead and ordered a new regulator (huma)as I am in there might as well improve it a little , I can feel the small leak coming out the hole where the air probe goes , Replaced gauge oring , to easy still leaking , Thought I would just order a o ring kit and valve for it , Nope there all over in the UK , Just wondering why no US based oring kits for the PP750?
Mike

So I have evanix tactical sniper rifle chambered in .357. The problem is it won't hold air. When I fill it up the air comes right back after I take the fill probe out.

Hi all, i recently bought a fx impact M4 in .25cal 700mm, i wrote down the factory settings in the manuel ( so i didnt have to remember!) But now like a total idiot i have lost the manuel and would like to set my M4 back to factory settings as i want a baseline to work from so i can start tuning slugs, can anyone with the same rifle tell me there factory settings please.

I just came across a gen 1 impact in .30. Is the fps in the low 800’s normal? Getting around 60ft lbs. Has high power huma reg set at about 200, hammer spring on max, and valve at 4 (all the way open). Any ideas to make faster with a little more power? Thanks in advance guys.

I ordered my Sidewinder from Airguns of Arizona about 2- yesrs ago. When I got it, I ordered 2 extra magazines and I asked them if they had any other recommendations, to which they replied, get a moderator. I asked which kind. They said they only offer one. So I added it to the list.

Everything arrived all stuffed into one of the pockets of that soft case it came with. I had assumed that they installed the new moderator and stuffed the other one in the pocket. But I've never been sure.

It arrived with the one on the left. But the adapter seems to be adhered to the shroud, as if it came that way from the factory. ..and I can't get the adapter to unscrew from the carbon fiber one on the right, as if it was installed that way from the factory. ..and I did have to buy an adapter.

I can see them using red Loctite at the factory. But that would be kind of ballsy for AOA to put red lock tight on an adapter that I didn't even tell them to install. And if that's the case, why not on the moderator? no other paperwork came with it. I've been stumped this whole time

Hello, this is my first post so i hope it's ok to ask some questions.

A very dear friend gifted me 2 air pistols to keep me busy and active during my cancer therapy. It's hard to do a lot of stuff we usually do together.

I dry fired the Daisy 717 a few times and it sounded fine... so i then tested it with a few projectiles.

The 717 shot very weak....and i could hear a little bit of rattling which didn't sound right.

I reviewed a video to learn how to disassemble the pistol but its very dark, tough to see fine details.

What i could find is that the wide bushing had disintegrated, almost to dust.

More worrisome is a little piece of plastic that looks like it broke off the rear sight....there is a tab that makes a right angle heading back up the rear sight base.

I guess i need new rings/bushings and a rear sight...are these available?

Also, where is there someplace to download a manual for the pistol. I found one for the 717 but it doesn't show assembly/disasemby and i can't find any for the Beeman 800.

Appreciate any leads and information as to how best to care for them and anything else i should purchase. I would very much like to use them.

thank you.

Hey guys - subject says it. This is a new one to me. I pull the handle back to load the next round and "hisssssss" I can hear air escaping. It's not dumping out - but it *is* most definitely losing air. I push the cocking arm fwd to load the next round - it's fine. Valve? I haven't dug into it yet - but will be. Thoughts?

I was wondering how much second reg pressure the stock fx impact m3 hammer and spring can efficiently handle?

New PCP shooter with a Stoeger XM1 scout .22. I'm having a lot of fun with this guy but have been asked to help a friend out with pests in her barn. I'm wondering if there is a limit to just how low a regulator can be set on this carbine? I don't want to ventilate her barn and will be testing with some scrap material but I've never adjusted a regulator before. Not sure if it's even possible to get down to what I need to be at. My guess would be under 400fps.

Looking for feedback on options between Burris Eliminator 6 and other similar scopes.

Finally found pp750 in 177 but I think it’s Canadian version as the brass valve hole is so tiny. Enlarged that hole with 1/16 drill and no other mods other than cranking the reg CCW to 2 threads above flush. Also maxing the hammer spring screw and backing off 1.5 turns. Only getting 570fps max 600fps about 7.6 fpe with 10.3gr pellets. What is going on? Is the reg not working properly? I tired adjust the HST but no change in velocity much. Does it mean I have to drill the hole where the reg screws into. Where it’s held by 4 long screws? Also should I also drill the 2 holes in the barrel tp? I watched the YouTube vid but found nothing about the 177.
Or should I buy a huma reg? hope someone can help.