Anybody know how much fpe a marauder .25 will have with a stock .22 mrod valve modded taking return spring out and end cap and using a 18lb heavy hammer spring with stock ports and hammer adjustment and air flow screw maxed out I plan on using Benjamin 28 grain dome pellets would like to push them at around 55-65fpe

So I’m thinking of buying my first high end pcp. I’m looking at either the cricket 2 or the veteran 2. What are the pros and cons of each and which d you prefer? Thanks.

Where's the cheapest place to get a marauder .25 shroud and barrel and breech plan on converting my marauder .22 to .25 gonna mod the stock .22 valve by taking out the end cap and return spring and putting in a 18lb heavy hammer spring also is a 50 grain noe mold too heavy for a marauder .25??

I was curious on what makes a big bore valve dump I got a .457 I've power tuned I took out the valve retainer and return spring got way more power but I was thinking about dumping all the air In one shot it has pretty small air tube only 150cc and 3000psi max fill how do you get it to valve dump??

Anybody know where there is 82cal bullet molds for sale 20mm??

Just had to replace a broken valve pin again on my AEA HP SS .30. This is the 2nd time now. Is there a reason they are made of plastic?

So here’s the story about 9.. to 10 months ago I purchased an MTC Viper pro from Air Guns Of Arizona. Now the problem I’m having is anything passed 15 magnification is cloudy and the parallax isn’t clearing it up. I sent it to them. They sent it back to me said the scope is perfect, put it back on the gun and sure poop. The same thing is happening again. I got on the phone I told them it not perfect it still very cloudy…..This was the answer. I got ……::::Well don’t use the past 15 so I’m just curious on what you gentleman and ladies would say about that answer

Is it possible to replace the bulky air bottle on a Bully with an AT44 air tube. I am not worried about the shot count, just want to know if it can be done.

Did they stop making the aea hp semi auto td

I just purchased a Gamo Maxxim .177 cal. swarm 2nd generation. Was wanting to know what type of chamber seal it has for lubrication. Leather or synthetic? Thanks for taking a look!

So I purchased a heavy hammer spring for my airicuda and I'd say it was a little to heavy. Backed all the way out it did shoot faster for the first 5 shots but then I went to cock it back and SNAP POW something sounded broken bolt went limp. Took it apart and seen that the little piece that pulls the hammer back ofcourse to my luck had snapped. I'm working with the guy who sold me the spring he says he can make a stainless piece that threads in but I don't see any threads. Anyone have any idea how I could fix this? Jb weld maybe?

UPDATE!!
I've removed the broken screw from the threads with an easy out bit #1
Alien Airguns on eBay is going to send a reinforced replacement pin bolt catch thingy. Shout out to that guy.

Hey AGN family. I recently went target practicing with a couple of my airguns. Upon returning home the cocking lever on my AEA .25 challenger pro came completely off. Does anyone know what kind of screw is used to join it back ?

Guys how important it is to store my pcp decocked???
Does it hurt the mechanism if I don’t??
thanks.

Fellow Pistoleros--- What are you folks using to transport your Diana Bandit or similar pistol (w/moderator) back/forth to the range? I'm looking for a decent soft case for this purpose. The Boyt case for the TC Contender pistol is just a little short, works OK though, for my Chaser pistol w/moderator. I do like the Boyt, but it's just a little short both on length and height to clear the moderated and scoped Bandit. My moderated and red-dotted Chaser fits in there nicely, though. You know, it's always SOMETHING.... Open for suggestions.

I'm thinking of getting started with PCP. I've got fairly extensive experience with powder burners and reloading, and I've played around with pumps and break barrels since I was a kid, but I know very, very little about PCP. Just reading through the forum tends to make my eyes glass over and my head spin. I'm retired military, pilot by trade, so I can handle the technical aspects as long as I can get a good foundation started. Any suggestions on where to begin the knowledge quest?

Hi!
I'm building up my 1st PCP; an FX Panthera in .25 (600 or 700) with the expectation of doing some long range shooting. I have 2 questions for anyone with long range air rifle experience:

1) What is the max effective range of a .25 air rifle? (How far out can you reasonably expect to maintain minute-of-pigeon accuracy and still have the force to do the job)

2) What magnification would you prefer (a reasonable min/max magnification)

Thanx!

Looking for the best accuracy and efficiency tune for a .25 cal 450mm barrel running jsb 25 grainers.

Hi, I'm looking for a moderator for my RAW HM1000x in .22 caliber. Suggestions?
Thanks in advance....
Geneeus

I own an inexpensive but functional and convenient $160 compressor from Amazon (https://a.co/d/8sHtOTR). I use it to fill my PCP rifles at my gun club. It’s LOUD even though it is a gun club and folks are shooting some loud rounds! I now see, however, what an advantage a carbon fiber fill tank would offer. I will study the issue so as to get other questions answered on my own but for now I would welcome responses to one question, please:

Can these modest compressors fill an Air Venturi tank without overheating or breaking due to the amount of air the tanks require? Or are professional sources - like “scuba shops” - really the only safe way to fill them? Thanks.

How do you guys like the aea hp semi auto td ?
I’ve had mine for a couple years now.i took the time to rope the scope all the way out to 140 yards I left it set for a while,picked it up and it’s 10 yards off on the scope dope stickers now. It’s a fun little gun but looks like I’ll have to dole it all over again

I have my list of conversations but when I open one nothing appears ??

I tried to report the problem but I get an error??

Anyone else have these problems ??

I have a pcp that shoot great with 18.3gr pellets. Less than 2/3 of an inch at 55 yards with pellets. But the projectiles I wanna shoot are slugs. Not high gr ones but 20-23gr ones because I don't wanna be shooting a motor with my 20-37ft-lb gun(no matter how I mod it, I don't get more than that and I gave up). As I was tuning for shooting slugs, I found out that my gun doesn't like shooting those slugs at high speed. So, I tried to find the highest speed I can get without getting grouping more than 2 inches at 50 yards. While I was tuning, I found out that at 1800 psi regulator set point and up, decreasing Hammer Spring results in increased speed. I found that out because I have the hammer spring tension highest while adjusting the regulator then reduce the hammer spring little by little for each regulator set point. As far as I know, normally, shouldn't the speed decrease with the hammer spring tension decrease?
I've been pondering on this one for like a week now and couldn't figure it out. So, I posted here hoping that someone would have an answer to that.

My gun specs.
18 inch 1:16 left twist barrel in 22 cal.
1800 psi is mostly the pressure I set on reg.
The air out hole on valve, I think called port, was 4.5mm but I drilled it to be 6mm.
Transfer way (the part on action block that connect the port to the transfer port behind the barrel is around 4.3mm and I cannot find a way to increase it because the hole is unreachable with a drill.
The brass transfer port is the kind with two elongated holes with a bridge between them. Total dimension of the holes should be around 6-7mm.
Using probe with small pin that push the pellets/slugs in. (Slug probe??)
My hammer has short stiff spring that reaches its normal state 6-8mm before the hammer hit the valve. I've recorded the hammer in action in slow motion and I don't see hammer bouncing between spring and valve.

What’s the most powerful pistol out today

Hello fellow air gunners does an make big bore projectiles now days

Hello

My Vixen is losing 10-20 BAR overnight from a charge of 250 BAR. I have owned this rifle for 6 months and this has just begun a week ago. Any perspective on this before I tear into it?

Thank you.