best and easiest way to install breech seals in air arm TX200.

My impact holds perfect first and second regulator pressure upon filling the gun to 250 bar. It shoots 20 feet per second faster for the first 5 shots Which causes it to shoot one inch higher at 100 yd. I tape marked all my gages for 24 hours and they hold steady.
My first rag is set at 175 and my second reg is set at 145 Shooting AEA 34 grain pellets.
I'm shooting at 920 feet per second with a standard deviation of one After the first 5 shots. My valve is at 4 lines. My macro is at 7 and my micro. Is at 4. Feedback.
Would be much appreciated, thank you.

So the above mentioned air rifle and I where shooting yesterday at 50 yards. The MKII didn't group very well and I swapped over to the 25.39 Exact Kings.
On power setting #9 they went all in mostly the same hole (see attached photo).

So the question I have is does it make sense or is it more efficient to lower the reg pressure and up the wheel setting? Or leave it alone in case I need/want to switch back to the MKII?

I can get two magazines (20 shots) when I fill up to 225 bar and refill around 160 bar. I believe I should be able to fill to 300 bar IIRC. Would reducing the reg pressure and upping the wheel increase shot count?

Please advise,

Smitty

ached photo)

Hello everyone,

I currently have a FX Dreamline GRS with a large Falcon x50 FT scope. I am finding that pesting in my yard is more my cup of tea and am considering getting rid of the Falcon. I am looking for a fixed mag option that is very lightweight. Probably 5x mag or so. A lot of my pesting is 30 yards and closer. Any recommendations? Should I consider prism sights?

Avenge X burst disk specs, anyone know what the thread size is? I blew it out @ 3800 PSI, kinda disappointed with that. Trying to find a replacement disk assembly. I'm getting these from Amazon but not completely sure if they are going to fit

Hello all. Looking for some help with thr crosman 2210 co2 repeater pistol. It was leaking so I disassembled and changed out seals but I have two tiny springs that I am not sure of their location. I have an old drawing of parts but it isn’t that clear. Any help would be appreciated. These are small coiled springs. I thing one goes by the trigger, perhaps behind it and one may go by the hammer. When I assembled it, it fired and held co2 really well but wasn’t cocking right or advancing correctly.

Hello Everyone,

I am planning to sell my FX Dreamline GRS w/ Falcon x50FT scope and accessories to purchase a more traditional springer type air rifle. The reason for selling is just due to the PCP platform in general requiring more gizmos and gadgets to use and use well. Firstly, I am looking for something that has enough power to kill woodchuck sized animals/pests pretty easily. Secondly, something accurate and fun to shoot in my backyard at targets, etc. I live on 3 acres with plenty of room to shoot up to 100 yards or so, although I would not be shooting pest further than 40 yards I'm sure. I do not have a strong preference on caliber but have plenty of .22 pellets..

I have looked at many options in the past and did my research but have been out of the hobby for about a year and don't know what is new in this category so figured this is a good place to start. I also need 10 posts before I can sell my PCP so I might as well get crackin. I have considered the Diana Airking 54, Hatsan 135, TX200, and Weihrauch's various offerings. I will likely get a fixed or lower variable mag scope that excels in target acquisition for hunting purposes.

Thanks for any insight!

Hey all,

So I’m new to PCP air guns - I had a few other co2 and springers, but this is a first. I went with the Avenge - X full synthetic. Looks like you can swap out to the tactical stock. I guess Im getting at which one?? There is a tactical stock chassis, a saber stock, ect.

I have the 210 tube not bottle - can someone send a link? If that’s allowed - first time posting

Thanks!

I stumbled upon a large inventory of UTG folding adapters that work with Buck Rail and other mil spec threads. I was wondering where I could sell these adapters and if this forum would be a good place for that? I have 6 left, but I can point people in the direction needed once these are gone!

I still have to make more posts and comment on others posts (Im new to the group) in order to post in the classifieds, but I'm working on that currently.

Thanks for the consideration!

I’m looking for a droop compensating one piece rail to use on my R9 break barrel that has a little barrel droop. Does anyone make something like that?

I recently got an Air Arms s510xs and am looking at getting an Arken EPL-4 6-24×50 scope on it. I am planning to pick up some BKL rings but I am not sure about the proper ring height.

Has anyone put this scope on an s510? Any recommendations on which rings will work well?

I have liked the BKLs in the past but am willing to use anything that works within reason.

Why is my fx maverick leaking from 2nd plenum when I try to tune for pellets.

I would appreciate any Ghost owners to share their opinions on a few specific questions, and also anything else you would like to add that is Ghost related.

How well does the gun fit off hand standing shooting, ergonomics, weight, pointability, etc?
Noise with your moderator for your caliber?
What regulator pressure are you using for your caliber?
Shot count?

thank you in advance for taking the time to respond. I will be selling my 25 cal FX M3, I have seen every BRK Ghost YouTube video made, and if your answers confirm how good I think the Ghost is I will be getting one soon. I do some hunting, some bench rest and a lot of silhouette up to 100 yards.

He has the

Snowpeak M16A -. &.25 for $344 i wonder if shipping is added to that to ship to Washington state? another place offers free shipping for the same price.Iv like to buy from Wess ?old fuddey duddy cutten corners' Willy I no i should,nt be playing with these toys at my age"I jus t sold a air gun for $600 bucks :ya no the feeling"​

Question for all of you. Is there another source for a compatible seal kit for an Avenger besides Air Venturi?

I have an Avenger in .25. It started a leak near the fill probe and would not fill or hold air. I am not mechanical so I took it to my local air gun shop (alamo air guns, great folks btw) back in March for inspection and repair. Inspection revealed that it needed new seals. Unfortunately seals from Air Venturi are back ordered. It's now AUGUST and they still haven't fulfilled seal orders. So, I have a useless rifle because my dealer can't get parts.

any ideas where I can source a compatible seal kit?

Thank You,

Hey y'all, I just purchased a .20 cal HW95N and was wondering what pellets your shooting brand and weight.
Thanks. Finally took a picture. I put a little blue tape on the sling swivel to keep it from scratching the barrel. She won't be winning the beauty contest, but she sure does shoot well

What is everyone using to refill there Huben GK1?

Hey guys, i just bought a Hatsan Vectis in 22 cal, and i want to do some hammer spring adjustment, but the problem is that i don't have a chrony to measure the fps. I can't buy one right now so i wanted to ask: how many turns would be okay to do to increase the fps to the maximum possible?

Hello. Own both CO2 lever rifles. Was wondering what people do to mitigate the shells going on the ground. I shoot in the basement , so I have a table next to me. Saw a film once where the shooter tilted the gun. Have a “ senior citizen” picker that makes it pretty easy.

The Walther Pellet is/ was really nice but appears to be out of distribution in the states. Have bought once in Europe but by the time the Walther( would get the Nickel) gets here; you were/ are looking at about $500-$600.

Got several nice Daisy 1894’s I shoot regularly. When you get down to it; they have been the best.

Any thoughts, thank you in advance.

Hi,
About the reximex RP pistol can I get it to 20fpe !?
I don't care about shot counts.
Can you share the max velocity the pistol can give at max hammer spring tension and reg pressure?
Is it safe to use a stiffer hammer spring ?
What about the results of drilling the transfer port?
Please share any stats about the international version of this pistol that comes set to 500-550fps.
Thank you.

When I take my bottle off the m60b it destroys a little o ring. Does anyone know the size of that o ring? Thanks

I have a Daystate Pulsar that runs on the LI-po battery. Daystate's website (under technical information) says "Charge the battery to 100% before storing the rifle, after this it can stay stored for up to 120 days.".

Relying on this I fully charged my battery as i need to store the rifle for a while, but later found out that on other products (e.g. R/C cars and drones etc) say never store Li-pos with more than a 50% charge. Now I have no way to safely discharge it for storage.

I don't have much experience with such batteries, and would highly appreciate anyone's advice/experience .

Thank you all!

I dont KNOW that it is. But with two of my three scopes i cannot raise poi enuff. Still inches low. Anybody know what gives? I mean ya shouldnt have to go thru this scope ring some do some dont song and dance With an out of the box brand new gun?I love the Wildcat, super SWEET tigger but all this scopin ringin drivin me nuts! Ive tried high low and mid rings… shimming too, ive tried high rear, low front rings… got sdjustables otw but seriously? seems a pretty major design issue.

Which one is better between Caldwell Ballistic Chronograph and Fx wireless chronograph?
Can i shoot through Caldwell while making groups at 30 , 50 or 100 yards ? I mean aiming for targets and measuring FPS at the same time.. is it possible??

Hi All I have a very early FX Crown (in the first 500 made) It has the 8mm reg piston - I only mention that to date it.

Now I have been out of shooting it for a while and it used to be an good gun and Shot JSB King Heavy MKII’s best at about 800fps and 120bar reg, this was how it came from the factory with a 600mm barrel.

I wanted to experiment with slugs. I watched all the usual Youtube suspects re tuning and got to work practicing on pellets first. In the end I got to about 155 bar reg pressure and had effectively maxed out the HST, on the MAX setting. it was shooting the MKII’s at about 930 fps but it sounded terrible, it wasn’t consistent, or accurate with the extra distance I could now achieve and I realised somewhere down the road I’d turned into a blind alley and this was just not right…

So Ive left the HST on almost Max when it was on MAX on the dial. I then reduced the Reg pressure to 100 bar, to start again. I had a tin of the lighter JSB Kings and started using them to experiment with. With my reg at 100 bar Im getting about 910-920fps with the HST at the “MIN” setting on the wheel.

Now here is what I really cant get my head around, and is making me question what I think I know…

When I keep the reg the same and increase the HST the FPS falls, and it does so linearly in line with the increase in HST so at the “MAX” position on the wheel I get 720ish FPS. Also the sound of the gun changes and becomes quieter and more “dull” less of a pop or crack and more of a hollow “thud”. what is more this is very consistent, if I turn the HST back down I get 920, back up I get 720. its not just all over the place

I thought that HST would increase FPS if every thing remains the same, or at very least it would not increase FPS, but to significantly reduce the FPS??? this makes no sense and I cant fathom how the mechanics of this would play out. I get that increased reg Pressure provides more resistance to HST so you get a shorter open duration on the valve and results in a decrease in FPS, but Im not touching the reg…so what gives

Can someone help me understand why this is? I thought I understood this, well until today!

Regards
SOTL