Got a 600mm in .25 coming Monday, going to shoot 40-50 grain slugs wanting to shoot 950 -1000fps How do I adjust the regulator, hammer spring , and dwell time properly? I haven't been able to find any video showing how this is done, thanks.

How do you install a 2-point sling on an FX Panthera? I know one point can attach to the Arca rail below the barrel, but where should the rear attachment go? on the stock?

Has anyone tried a Airforce airgun in .177 for Field Target compe?

Does anyone know of someone in the Buffalo, New York area who repairs PCP pellet rifles?

Does anyone know of someone in the Buffalo, New York area who repairs PCP pellet rifles?

I'm looking to buy one of these slow twist barrel in .25 .. could someone point me in the place to buy one .. thank you

I have seen the other posts but a bit confused. I would love to find the cheapest most effective mod to quit it down if that’s baffles or any type of moderator and you have a product please post it here. Also mags. I would like to upgrade to a bottle but I’m not going to bother if I can’t find a 4500 regulator/adapter. If I am missing something please let me know. I have been shooting at about 2500 at 905 with 25.39gr and get about exactly a mag worth out and it’s time too fill. It’s worth it for how accurate it is. First PCP gun and Love it! 75yrd on the target smashing the red

Just got this Vevor pump.
shot the pistol into the yellow zone to test the pump.
After 100 pumps nothing changes on the gun or pump gauge.
Pump looks to be undamaged and In perfect condition.
Am I missing something?

Hello everyone,

I recently purchased an Aselkon Ravello RX5 from a gunsmith who unfortunately doesn't seem to be familiar with this model. The rifle came with a general user guide for Aselkon (see attached photo 1), but there's no specific manual for the Ravello RX5.

I would greatly appreciate it if someone could provide me with the specific manual for the Ravello RX5 in digital format, or let me know where I can find one.

Additionally, I have a question regarding the two pressure gauges on the rifle:

First pressure gauge: Located on the tube, it shows a pressure of 200 bar (see attached photo 3), which corresponds to the pressure in the tube.

Second pressure gauge: It indicates a maximum of 110 bar (see attached photo 2).


Could someone inform me if the second pressure gauge reflects the pressure of a regulator, or if it serves another purpose?

Thank you in advance for your help.

Best regards,

Salim Rami

Is a key also required to charge the Daystate Airwolf? Without the key but with the charger plugged in, I am not getting any flashing light to indicate the battery is charging. Initial screen readout indicates the battery is at 8.5v.

Hi people of the internet do anyone know where i can finde an replacement oring kit for my Air vinturi avenge-x

The leak is on the high pressure side because the fill pressure drops belowe the reg and the reg is stil what it is set to eg. fill wil be at 100bar and reg pressure will stay at 150 bar whilst the bottle keeps on decreasing

what is the diameter for the .30 cal shroud thanks for any help

Hello, first post on the traditional airguns forum. So I am getting into air rifles and have previous experience with the diana 34 I bought for my dad. I liked it quite a lot but was wondering about getting a 460 as I like the idea of higher power and fixed barrel. What are peoples opinions on it?

Hello, I'm tom new to this particular site which thus far i think is great. I am a little concerned about such a large list of scammers though. I'm just getting back into the hobby after a couple year. I'm looking very hard at the aea challenger in .25 or .30 does anyone have a good amount of experience with them any kind of info good or bad would be very helpful id really appreciate it guys.

I recently purchased an M4 in 177. Ive only shot one mag so far and Im assuming thats it but I had a dev of 100fps. If I cut the two worst shots im at 56fps. Like up and down between 790 and 830ish throughout the whole mag. Is this normal? Thanks!

I have inherited a HW 50S (nice gesture from in-laws). Papers with the air gun show a date near 1979-80, made in West Germany. The air gun does not have a safety lever shown in manuals that I have read, videos demonstrating, reviewing this model. I see no visible safety mechanism at back of barrow. After loading pellet and cocking gun, trigger seems to pressure a trigger point, but not firing. Am I missing a safety somewhere else? Do I have a malfunction? Air gun has been sitting unused probably 10 yrs. Thoughts on safety location and other next steps? Thx!

OK guys here's one I can't figure out. My scope is shooting at about 7 o'clock 3 inches from bull ( at 20 yards) and my elevation is all the way up. How can I get back to a normal adjustment. I had this rifle dead zero before. I moved the adjustments about 40 clicks and have no more room to go up. It hasn't been banged or anything. I really don't know what to do. Any help would be greatly appreciated

What weight pellet does the FX factory use to set-up the FX Impact m4 Compact

I recently purchased the Hammer and have been sighting it in using the 550 grain slug. I have very good accuracy at 25 and 50 yards, however at 75 and 100 yards there is significant drop with the 550 slug. Anyone else using the 550 slug? For longer distances should I go to a 350 slug?

hello I have a Hatsan bt65 .35 cal and when I pull the trigger it’s just a click I’ve tried at different fill levels between 1 bar and 2 bar and have also tried at several hammer spring adjustments with no luck . Could it be the airclynder valve or is it more luck let the hammer not quite sure on what to do next so anything helps

Hi,

I've been shooting centerfire the last 3 years, so I haven't been keeping up with Airgun developments, but recently my last two PCPs (RAW HM1000 and a FX Crown Continuum) and a bunch of my powder burners were liberated from my storage unit. I was storing them while our house was being remodeled and I thought they would be safer in storage than in my house with all of the construction crews coming and going, but that proved to be incorrect. At least it is all insured.

I still have all of my filling equipment and a ton of 25 Cal ammo, so I will probably buy a least one new PCP. It will be used primarily for practice and pest control. The FX DRS Pro/MDT is interesting because I run a MDT ACC Elite Chassis on my primary PB competition rifle, but it's expensive and has a very limited shot count. I'm also considering the FX King (probably would buy a synthetic and swap out the stock for a Saber Tac Chassis) and maybe an Impact. I owned one of the early Impacts which I really liked, but I ultimately sold it because I spent more time tinkering with it than shooting it.

I'm assuming the newer Impacts are probably a much more stable platform than when I previously had one, but I'd love to hear from some folks that are currently running Impact M3s or M4s. I know they shoot great, but I want to be able to take an air rifle out of the safe and know I can pop a pest with it even if I haven't touched the rifle in months. That wouldn't have been the case with my first Impact. That was what I loved about the Crown. It could sit for months and would never lose pressure and would shoot just like it did when I put it in the safe.

If you have personal experience with any of these rifles, I'd greatly appreciate hearing your thoughts. I'm probably leaning towards the Impact right now primarily for it's versatility and accuracy if it's not going to be a maintenance headache.

Thanks in advance for your thoughts!

Do I zero the scope and air rifle straight out of the box and then do my tuning to preferred pellet/slugs.
thanks in advance.

Hey everyone -
I've made some progress on my Notos so far, upgrading to FX 380mm barrel & CF shroud from c88, UTG BugBuster scope, polished some internals, etc... - I recently put everything back together after some deep cleaning & attempting to change out the poppet valve with an MCP version, but proved to be a little off - I was advised by a senior that the design can be problematic - stem length, etc - so I went back to the stock. All that aside, I get everything back together and with a chrony on the end I shot off several mags - and started out, I was hitting 400+FPE (?) - and what was weird is that by the time I fired the 30th pellet, it's back up to 790 where it was before cleaning. (I did use correct lubricants on the different components) - so I let it sit a day, came back to it and refilled to 3600 - and same thing. Gradual increases up to the 790 it was set at before. I'd noticed a couple of times even before all the cleaning that my first cold shots were coming out 500-ish FPE, but next couple jumped up to par.
Second, my scope alignment. I was finally zeroed in where windage/elevation were right around their mids left-right / top-bottom adjustments. I put back on and laser boresight, the windage isn't centered without the adjustment maxed out...I took off, loosened & retightened the rear pic mounting screws as I read the POI is sometimes an issue from the Notos' short rear pic rail - then put everything back together super carefully - and same thing. I shot to make sure it wasn't the boresight laser, but it wasnt' the laser.
So in short, Scope alignment must be off somehow, but what would have changed? And what would I focus on first to improve my FPE to shoot what it should on the first cold shot? I appreciate any ideas, I"m learning as much as I can. Thank you -

Back in August I purchased a PCP air rifle, then I purchased a Vevor Compressor. When it arrived the box was damaged. After inspection one of the cooling line fittings was broke off, no big deal to replace. I also found the top air line bent. I contacted Vevor for a replacement, they refused and wanted a video of it running. I told them they were nuts to think I was going to start a damaged 4500psi compressor and video it for them. They persisted and requested a video before anything could be done. I turned the table on them and requested an email of them accepting liability if anything went wrong while making their video. They immediately refunded my money and said dispose of the compressor. I took the compressor to a company in Edmonton AB that deals in high pressure SS air lines. They inspected and assured me that the lines are meant to be formed and the extra bends are no issue. At this pint I hunted down the special oil required and filled it. When I plugged it in and hit the start button, all it did was buzz or humm. The Vevor compressor failed to start. I can turn the compressor by hand and it rotates.I tested the start capacitor and its good. I dont think the start capacitor is getting power. Can anyone shed some light on this problem, it would be greatly appreciated. I am almost at the end of my patience regarding this venture and tending to want to sell the Air Rifle and be done with it





,

So added some hammer weight to my m4, watched some assembly videos for the hammerseat. They say 6-6.25mm for the hammer seat, however I noticed that now the gun won't chock when the micro wheel is above #4. Is there something Im missing? Is there an actual service manual available for the fx impact rather than videos?