What is the twist rate of the Snowpeak m60B cannon? CAL.22

I have a brand new hatsan sortie. Put the donnyfl barrel end adapter on it and now it doesn't cycle semi auto. Took it off and checked/lubed the spring. Still the same. Will shoot single shot bolt action style ok but I bought it because it it semi auto. The bore diameter is smaller, too much back pressure?? Any advice would be greatly appreciated.

I am new to the PCP world and received a Hatsan Jet 1 for Christmas and recently bought a Spritech compressor off Amazon. Over the weekend I attempted to charge the Hatsan and my first roadblock was that the quick connector would not operate properly and then I read somewhere that some fittings require the O-rings inside have to be removed. I removed both of them and the fitting worked properly. I fired up the Spritech and made sure the bleeder valve was closed following along all the instructions in the manual and after approx. 15-20 minutes neither the needle on the compressor or the Hatsan had moved ? Am I being impatient or ? Any advice would be greatly appreciated !

Is there any body to contact for support on this site? Been trying to PM, but am unable. Ty

Hello. I am looking at purchasing a fx wildcat sniper to squirrel hunting with but it seem the magazine will be in the way? , any input greatly appreciated. What other recommendations? Thank you

Hi,

Do I need to re-zero or make any adjustments to my scope if I move my entire scope an inch or two forward?

Hello, I just purchased a Bullpup .22 Stoeger pcp and the guy who sold it to me told me that it's about 50 shots before air refill.
Strangely, I'm able to shot more than a 100 shots and the pressure gauge is still at 130 bars.
How can that be? Do I need to higher the spring hammer? I live in a country where it's hard to get good answers...
I noticed that the gun is shooting below the target at 60-70 yards far. At short distances I have no problem but the longer the distance the lower the target.
Please advise.
Thank you

Anyone know how to disassemble a Falcon FN-8 with the safety on the side in the wooden grip. My stock is basically shaped like this one.

From the title, the charging handle on my M4 is/was hard to close. I was have a pin probe for shooting slugs and I had it adjusted to what I though was the 'correct' depth for my gun. Today I ended up pulling my barrel off and after reassembly the charging handle the last little bit before it would close became very stiff. I ended up backing the set screw out and adjusting the pin a little further out which did make the handle easy to close again.

Not very familiar with how all of this stuff works together so any feedback would be great!

Thank you in advance!

So, I just dropped my FX DRS into a Deltaforce chassis, and it is nowhere near centered.

While it is not making contact in the barrel channel, it is bothering the hell outta me.

am I wrong to expect more from a $1,000 chassis? Has anyone else had this issue? Any suggestions?
Thanx!

I'm looking at a used Diana 52, T01, .177. Is there anyway to get more info on this gun? Like if it's a reduced 12 foot pound UK model or a full power model. The asking price is $250 USD. I'll try to attach a couple photos. Any info would be appreciated. Thank you

Just purchased a sig Sauer P320 with some .177 pellets I loaded the ammo in got 3 shots and it jammed. Is there a specific pellet that I'm supposed to use and maybe some kind of lube maybe silicone. Some advice would be appreciated. Thanks in advance

Has anybody tried to use these in an bin tac s45

Does anyone know if anyone make a handguard / barrel cover for the s45 with a regulator? I know they make one for the unregulated version.

I was able to get the bottle free from the action, but as you can see in the pic there is still this adapter connected to the bottle which will prevent me from slipping a depinger brush inside.

it was already really difficult to get the bottle off, and now this little piece seems all but permanently installed. I can’t tell if maybe that bit that I have circled in red is just paint, or if this is somehow tack-welded or glued in Place. I suppose I can get channel locks and try to wrestle it off at the flat collar/“cap” (though that might chew up my connector) but I want to really make sure I am not doing something wrong before I go brute forcing my way to a damaged gun.

what do you think, muscle this thing off? Or is there something I am missing?

Do you use the same suppressor for multiple guns or do you get each gun it's own?

Hi folks,

Wishing you well. I would like to remove the tank only from my Kratos, to slip a bottle brush in to it and maybe coat the outside.

I’m not really sure how this is done, and don’t want to remove more than necessary.

Could someone please tell me how to remove the tank properly?

thanks!

Have a question if you was going to buy a new fx impact m4 would you get a .22 .25 or .30? And why? I'm won'ting one to shoot around the house and shoot some long range and hunt some with

I needing some input im looking for help impact won'ting to buy a fx impact m4 or a m4 compact wich would you buy and why .22 .25 or 30? I'm just looking to shoot around the house but would like to be able to shoot some long range also. Won'ting to shoot stock before I start upgrading all help would be appreciated thanks

My Daisy 851 was leaking so I bought a rebuild kit for the 853. everything looked pretty much the same but now after reassembling it, the first shot is quite weak, but if I cock it again (not repump) then it will shoot again a lot more strongly, and sometimes it will even do this a third time on the same pump. I have not tried a bb or pellet in there because I'm afraid that first shot might be too weak to shoot it out. IT's supposed to release all it's air on the first shot so this is really weird. what have I done wrong?

Anyone using fx impact m3 for coyotes? What pellets do you use?

On the fence over here and I’d like some input from the group. I’m looking at the Benjamin Bulldog .357 and the newly introduced Skout Epoch compact (would opt for .30 cal). I’m shooting pests including coyotes, raccoons and so on. I know it’s hard to talk about the compact so any experience with the regular epoch would be appreciated as well. Thank you!! Ideally I’d like both but.. well, you know

I have a newer Hatsan 95 Springer in .22 and it's velocity is well below spec. I'm getting 659 - 680 fps with 14.3 HP. Hatsan lists it at 800 fps and others are reporting 780 - 830 fps with the same ammo. I let it go past the warranty period since I didn't have a chrony until recently. Any suggestions on what I can check to find out the problem? Thank you

I have been tinkering with my Ghost, swapped springs out for the White spring and then Blue spring, and testing different reg pressures and now it is only able to achieve ~620 FPS with the following configuration.

BRK Ghost .22 HP
23" barrel
Red Hammer Spring
Tank ~190 BAR
Reg ~165 BAR
PW Max
JSB Exact RS Diablo 13.43 gr.
FPS = 622 (highest)

When it first arrived it was cranking the JSB Hades 15.89 gr pellets at close to 1030 FPS with the following configuration:

BRK Ghost .22 HP
23" barrel
Red Hammer Spring
Tank ~190 BAR
Reg ~150 BAR
PW Min
JSB Exact RS Diablo 15.89 gr.
FPS = 1030

I am charging it from a Yong Heng compressor with this secondary water/oil separator in line between the compressor and the gun.


I should also mention that when degassing the gun it is taking 15+ shots with the PW on MAX setting before the reg pressure drops below 50 BAR, not sure if this is relevant, but from my limited experience/knowledge it seems to indicate that perhaps the valve is not opening fully?

Any thoughts or suggestions on what might cause this behavior?