Hello, what small airgun would you recommend for front yard squirrel hunting? I have nuisance squirrels that have refused to get in the traps since last September, and now the nerve of them, they are courting to reproduce in my front yard! No, thank you! I need something that can finally end the squirrels, but won't ricochet into the neighbors' yards across the street if I miss.

My trap has been a Squirrelinator, with peanut butter, sunflower seeds, various fruits sometimes, etc. why won't they GET IN...

Also, I don't have very strong wrists, so I might avoid the pump action ones. But it's not like I'll be using a whole canister at a time, and those can get pretty expensive if just firing a few shots and then the rest of it leaks out from non-use. I don't know much about these things... and could use some advice.

100 cubic foot 4500 air tank or a 4500 air compressor better for being a couple hundred miles away from civilization for a week 2 to 3,000 shots per day

Hey guys just a friendly thank u for all the comments on. My messed up guantlet 30 sl .being an hvac technician it's tough for me to ask for help being mechanically inclined. But alas they don't call me mikey fingers for nuthin. My pointer and middle finger on my left hand was amputated below the knuckle, so instead of having 2 good hands now I have 2 pinball flippers as fingers on my left lol .the airgun family is full of great knowledgeable people who will help if u ask .big thanks and shout out to Andrew "toxic matrix", hajimoto productions ,nate at the airgun channel ,macabeespeed and Rob Vogel aka Mr hollowpoint for all your help advice and guidance. And thanks again to all the airgun nation folks and their kind words

Let's say there is 3,000 psi already in you PCP , but you want to top it off to 4,500. Is there something you need to do , so it won't mess up your compressor.

Hey guys.

I have this adjustable front aperture from Anschütz.


It’s constructed so that there are two internal lenses with the iris built between holes cut in both lenses.

I need to figure out some way to clean the inner sides of these lenses. The outer facing sides are no problem. But after months of outdoor shooting, they are getting a bit foggy on the inside.

Any ideas? Previous experience?

Thanks in advance!

-Delta

I am wondering if anyone can help me. I am trying to find the outer diameter of the Bmarex Gauntlet 2 barrel and the inner diameter of the shroud.

I found way back in my dad’s closet Crossman 2300 T I guess some of the seals inside or shop because it doesn’t hold air for very long. Maybe get two shots. Anybody have a line on new seals where I can purchase
I’m new to this form and I couldn’t find much on the Internet
Thanks for everybody’s help

Hatsan Hercules Bully Leak

I am clueless on how to t/s huge leak on my Hatsan Hercules Bully .30 Call. When charging my Hatsan Bully, I can feel air blowing all the way back to the receiver area, and I can hear something rattling in the cocking mechanism area (body) when I move barrel up and down. I do appreciate any help/suggestions on how to t/s and fix it.
Went to hatsan website, they do not have any "How to Videos".

Anyone experience Hammer Creep with their PCP. I noticed this on my Avenge X today FPS started out at 880 fps and slowly dropped down to approx 850 fps. Checked the hammer and it appears to be locked all the way in. It started out at 2.5 turns CW

I have an umarex gauntlet 30 sl had it 2 months now put a tin of jsb exact diobolo 44.75gr thru it like a Lazer beam sooo pleased then 100 fx hybrid slugs ran great up till the last 3 shot 1 cocked the lever ,as I pushed the bolt lever closed felt like it was getting hung up before the probe enters the barrel shot 2 and 3 got more difficult so I pop the mag out safety on and tried to cycle the bolt.pull the lever back now volt only goes half way and stops ..calked umarex no response yet hoping warranty covers this 1 .any ideas guys? I'm not ready to take this thing all apart not that knowledgeable just yet ..

Has anyone received the corrected weaver scope rails? or any news .
thanks in advance.
S.

Why is it that in “.22” cal, most major manufacturers offer .217 and .218 (so they’re undersized quite a bit, and Nielsen goes all the way from .216 up to .219, yet in .25 it’s mainly .25 only, with a few .249 (under), or a big jump to .253 (over). In .30, that’s it, with patriot and Nielsen offering .301 and .303 as well - no under sizing…

Matt

Just wondering if they're worth a shot over JSBS as the price difference is obviously there.

Hi i bought a older bam under lever .22 rifle that has trigger mechanism problems ive stripped and re build it multiple times and still can't get the trigger mechanism to work. Any help to rebuild and get this old girl working again would be very much appreciated. I've rebuild my smk 19 multiple times and had no issues its just this BAM Which I believe is a b4-4 I'm having trouble with. Thank you in advance.

Has anyone used? Good, bad results?

Has anyone had issues fully seating your barrel into the new power blocks? I have impact gen 1 just upgraded to the 750 power plenum and power block but the barrel notch is not fully wanting to seat.

I just took out my reg. due to the creeping issue and realized that FX had updated the piston (see picture below) since the polishing video posted by Steve from "Precision Airgunning - Long Range Target & Hunting". I'm wondering if we can still use the same polishing method for the new piston?

OK folks I'm waiting to go to the hospital to get my steroid spinal injection in my lower back ,so just a dumb fun question. Zombie apocalypse hits but not wwz zombies ,slow one like basic walking dead in a fortified house no firearms left .electricity is working pick the airguns u think will help u .got plenty of airtanks ammo as well .it's in ur favor have fun !

Could these tariffs be a blessing in disguise for American airgun manufacturers and a few other nations .and is it possible for these companies to say ,drop all guns 10% off retail .could a company corner the market and still make nice profit while satisfying consumers?? I know probably a pipe dream.

Just installed power block and 750 plenum on my gen1 impact. Everything went well except….when screw bottle in it starts leaking at back reg gauge. Anyone run into this and know what I need to do???? Thanks

Who works on the Huben Gk1 ? Looking for a possible optio.

I bought the Panthera Slug Power kit and installed the hammer on my .22 Cal, but I'm hesitated to install the pin probe because I'm worried the pin probe won't push the slug deep enough past the transfer port or even to the liner, because it really depends on the slug end shape, if it's flat base, the pin probe should push the slug to the same depth as the stock probe does, correct? But if it's dish base, it won't get as deep as flat base? Do anyone get consistent result from installing the pin probe? I have a lot of Javlin 34gr and 40 gr for my Panthera .22 Cal 600mm, do you recommend me to install the pin probe? If so, how many fps will I gain by that? Thanks a lot!

Gentlemen,
A friend of mine has an air rifle torn apart and looking for a brand or model but can't seem to fine any identification. Anyone recognize it from the pictures, or care to take a stab at it.

Thanks

My diana 240 reached 8000 shots(16 tin can) few days ago and I know the mainspring almost reach the end of it service so I want to do mainspring replacement but I cant find any seller sell that part.
So i do some research and got that Hw30 mainspring is .113” wire x 26 coils x 190mm lenght and diana 240 is .106” wire x 29 coils x 200mm L, both of them use 25mm tube
I have no experience cause 240 is my only gun for many year. But look at those numbers, something tell me that 240 spring cant fit hw30 but that hw’s spring can save my 240
I know this forum has lots of pro springers so Im here to get a confirmation
Thanks in advance and have a good night!

I was airing up my gun today and noticed my regulator gained around 30 bar while filling up. This isn't normal is it? Thanks