I miss my fox maverick was such a good gun

anyone in Ohio looking to part ways with an airgun ?

Does anyone have a Pic of the case that a dynamic compact 25 cal comes with? If so please drop a Pic. Thanks

Look to pest birds and foxes and maybe coyotes if any pop up any feedback ?

Hello
I have a brand new rifle , zero tunning.First time i've tried to set it on 175 m/s on 0,177 calibre.The speed was very inconsistent.I 've changed the plenum to a pellet plenum.Much better but far from good.I understand that the rifle will not work on that speed,and i try to set it to 16 J , maybe on a higher power will be more consistent. The chrony shows me 2-3 m/s deviation.Ok.I put the rifle in the case set on 16J ,next day the first 5-8 shots are 25-28 J .Two things was set by me.The regulator and the hammer spring . Why is the speed increasing with the smallest plenum?

Hey guys my youtube channel new sentry arms is up and running go to youtube.com@mikeyfingers-ns mostly short form check it out .let me know what u think ..warning I can't film yet so bare with me lol .any ideas insight?

I have a Diana Bandit in .22 cal. Haven't shot it in a while, so today I thought I'd shoot a bit. Problem is, it will not hold air. Fills OK, but as soon as I bleed off the compressor, the air cylinder bleeds down too. What do I need to do to correct the problem?
As always, thanks in advance

Hello .
Could someone help me / advise me why the speed of the bullet changes significantly with the Epic Two 700mm. The first 3 shots were perfect at 100 meters but then they started to have a big spread so I measured the speed and it jumped from 290m/s to 220, 310, 250...

My apologies if I missed this specific leak discussion.
I can charge my M3 to 250 Bar and within a few days, the bottle pressure gauge and the first regulator gauge show 160 bar and the second regulator gauge reads 90 bar. I've used leak detector on all the usual suspects but no bubbles. Any help/suggestions would be appreciated. TIA

Anyone tried 59 gr Zan slug in .30 FX Panthera/Dynamic or King with 600mm superior heavy liner?

I recently purchased a P35X in .177, primarily because of the added 65 cc plenum and the longer barrel. I purchased it from mundilar in Portugal so no power limitations.


However, I can’t get it to shoot faster than 860 fps with JSB Exact Heavy 10.34 grains even with the hammer spring fully adjusted.


I’ve also tested:

• JSB Beast 16.20 gr = max 720 fps.
• JSB Monster 13.43 gr max 776 fps.
• JSB KnockOut Slugs in both 10.03 gr and 13.43 gr max fps = even less then the two pellets mentioned above.

• I expected it to have around 29 fpe with the jsb beast 16.20 according to others reviews, but I'm close to half of that fpe, 18, 65 fpe / 720 fps when shooting the jsb beast. 16.20.

Has anyone experienced similar performance limitations – and found a solution?

I've noticed depending on the weather the air guns I have will fluctuate what it displays on the air gauges from day to day even though I haven't used them
I was wondering if anybody else has experienced similar things with the air guns
Sometimes I will leave them in the truck but I was wondering people's thoughts on this specifically pertaining to notices in PSI based on the weather
The fluctuations I've seen have been minor but I've noticed them

Anyone know of a single shot loader for the Karma Red Panda? Darko at CARM may make one if he can get his hands on an RP but he has not so far. The RP includes BEAUTIFUL magazines, but sometimes I just like using an SSL.

I want to tune my Daystate Pulsar, was gonna have AoA do it but I'd have to leave it with them for 2 weeks which I don't want to do. If anyone in the area has one I will pay for the time (and I haven't tuned it before so I'd pay for your time)

Are those 2 pcps in the same power range?
Looking to sell something to buy my first multi caliber gun .. I'm really looking to get the best out of my Corbin setup.. Looking to shoot between 38gr to 40gr slugs . Is the mora front Bipod picatinny rail extension solid or a flimsy pice of metal ??

Hi iv got my hands on an .22 fx maverick low powered 12ft/lbs of power , Im changing to a .30 highpower or normal US powed long distance slug rifle now I have my licence at long last again.

Iv now got a .30 sniper 700mm barrel change kit .
Can you or somone please list what other things I need to change . what has worked for you .
I want to use for long distance small game and also just target shooting.
I'm fairly sure I know most of what I need to change but I'd like someone else's opinion that has been through the process themselves. after doing a change from.a pellet rifle to a long distance slug rifle.
What parts , hammer weights/ hammer springs / regulator bevel sizes and even ttypes of slugs and heavy pellets that work with the same pin probe , I'm told some can damage the pellet skirt??, depending on magazine.
I'm useing huma as my main shop to buy items so if a list can be given of items from there it will be a big help .
Any help.in.a list of parts I should be changing will be a help .
Sizes of the regulator bevels would help as i belive there different in the uk sub 12 ft / lbs low powered ones. Recommendation's on .30 .3D printed magazines and aso if there is a supplier of larger quantities of slugs rather than tins , tins are fine till I know what weight of slugs I'm going to want , but after that I love spending full days on the range and doing some small game hunting at much longer distances than the 50 yards a 12ft/lbs of power without a licence. The cost can soon get to much unless can buy in larger quantities or make myself.
I will be getting a press which again if there's any people recommend please say.

I'm a little confused about the hammer wheel as I'm not to sure if mine even has been working. i do have an FX hammer quick tune kit that il put a photo of below which I'm told is great for micro hammer adjustments.

This might sound stupid but should number 1 be at the bottom between the two lets call them posts as the first setting,? should the wheel stop turning once it gets to highest number ?.Then it should stop and you spin it back?.
Mine just turns around and around which seems wrong to me ??. Surly it's should stop once it reaches its max then you can turn it down , not just be able to spin it all the way around.?
This rife is new to me and second hand at a bargin price luckily and iv purchased knoeing it's a great rife to work on and learn from before looking a buying other long distance rifles in the future now iv had to give up the shotgun due to injury.

Regarding regulator settings. Can you advise on a good starting point with .30 slugs .
I do now have an fx chronograph just purchased so I'm sure it will help but some advice from someone with experience would be a great help . Videos are only so much help and you need to k ow what help you need first .
I like to.print and be able to have there in front of me .
It helps me alot as i hate been outside with gace glued to phone screen instead of the scope.
Any advice li ks to other threads would be a huge help to.someone that now wants to get hand into the joys of playing and changing part on pcp air rifles, especially when my closest shop is a 800mile round trip

Thanks for your time and hopefully experience.

I bit the bullet ordered n next week my first swaging dies should arrive. Any suggestions on the lead wire I should get?

A question that I have come up with when looking for this rifle is regarding the tank output pressure.

I've read that 1100psi is the recommended output pressure from the tank, and also what the supplied tank is set at.
I know some people have experimented with 1200psi for increased power.

However I am more interested in performance with lower pressure.
Has anyone tried running it with regular paintball pressure of 850psi?
Did the action function? If so, what was the performance like?

Forgive my ignorance. I have short term memory issues and thus the apologies right out of the gate if this has been answered repeatedly. I have searched for info but may have already forgot what I've read because honestly, that's something that that happens. I've been researching for a few weeks now and was just about to make the purchase of an Avenge X and misc. associated gear, thinking I had things lined up in my head of what was needed. But, just to be certain, I asked via customer service chat at Pyramyd Air about what size bottle I should be looking at for an Avenge X via a used Scott 4500 psi SCBA bottle as I may have access to a few (I'm a retired/disabled Paramedic). However he stated and I quote "The size of the SCBA will not matter. With the high fill pressure of the gun, even a tank filled to 4500 psi, you will get less than 1 full fill of the gun. A compressor is a better option for the Avenge X."

This is blowing my mind. With everything that I've watched and read over the past few weeks, I was under the impression that once I had the SCBA refilled, I could use it to refill the rifle multiple times. Granted, I had no clue just how many refills might be possible, considering all the possible variables including but not limited to original starting pressure, how many shots taken, altitude/barometric pressures, etc..

Can the wise and sage ones one here maybe give me the real skinny? Clue this old man in to what's really going on? Was this just an attempt at getting me to purchase a high dollar compressor right off the bat or is this information correct? Something doesn't seem correct here.

Thanks for any advice you may have.
John

Hello all,

I have a Steyr challenge Field Target that I would like to make some changes to. Specifically, I want to change out the default hamster for a custom one. Does anyone know what rail mounting system Steyr uses for their “front stock?” I want to confirm if it’s proprietary before I start shoving in m-lok rails and damage my chassis.

I just bought an avenger x .25 cal today. this is my first gun so I am still learning. On the regulator gauge when you switch from high to low should you see a different pressure on it? I will switch it from low to high take a few shots then look at the gauge and not notice a difference.

While blueing is commonplace with steel guns, I’ve never seen it done with alloy. I think the most common alloy used in many airguns is zamac. I remember people saying you can’t blue that stuff, only paint it or anodize it. Is this still true or is there something new out there?

I haven’t been here in awhile. Was wondering if anyone has any firsthand knowledge or experience with the MAX 1? It looked to be a pretty nice set up with some good stats.

Bakersfield California area if possible I need someone to fill my Scott 4500 PSI carbon fiber tank ! Tried rebuilding my yong heng compressor with no success and really would like to get out and shoot my PCP rifles I will compensate for the fill. Would be very nice today if possible!? Thank you!

Good evening,

I have just recently purchased the MCAR .510 caliber Hunter version and am looking for suggestions on a quality optic for it. I was told the Monstrum Ruckus Pro 6x Fixed Prism Scope would be a good one. Any comments?