Join HERE
Zbroia Kozak 177 arrived today
Forums › PCP Airguns › PCP Airgun – Discussion › Zbroia Kozak 177 arrived today
-
Views : 24279 Likes : 0Likes : 0
-
March 12, 2018 at 9:19 pm Link
“BigTinBoat”
“RAMJET66”I removed the stock yesterday, to straighten the cocking lever, which is only a very temporary fix , it is very thin , I hope the new ones when they get here, are improved .. anyway I decided to turn the H/S tension down, as it is shootin close to 900 w Jsb 18 .34’s so I marked it with a sharpie, & backed it out 2 full turns, & the stock would not go back on with the mounting holes, ( with the H/s tensioner backed out , it was hitting the the wood )so I got a dremel & started removing the wood for the back screw hole to line up, but there is not a lot that can be removed, as it is close to the brass thread , so I ended up turning the H/S back in a 1/2 turn to even get the stock back on , so it l;ooks like I am stuck with the H/S setting that still uses way too much air, but I still like the gun , will like it even better if & when I receive the New cocking lever..
you should be able to just take a coil off the spring and turn the adjuster back in a bit…..duh I never thought of that, thanks BigTin , but I think I would rather find another spring to try instead of experimenting on the stock one..
"BigTinBoat"
"RAMJET66"I removed the stock yesterday, to straighten the cocking lever, which is only a very temporary fix , it is very thin , I hope the new ones when they get here, are improved .. anyway I decided to turn the H/S tension down, as it is shootin close to 900 w Jsb 18 .34's so I marked it with a sharpie, & backed it out 2 full turns, & the stock would not go back on with the mounting holes, ( with the H/s tensioner backed out , it was hitting the the wood )so I got a dremel & started removing the wood for the back screw hole to line up, but there is not a lot that can be removed, as it is close to the brass thread , so I ended up turning the H/S back in a 1/2 turn to even get the stock back on , so it l;ooks like I am stuck with the H/S setting that still uses way too much air, but I still like the gun , will like it even better if & when I receive the New cocking lever..
you should be able to just take a coil off the spring and turn the adjuster back in a bit.....duh I never thought of that, thanks BigTin , but I think I would rather find another spring to try instead of experimenting on the stock one..March 12, 2018 at 9:25 pm Link“jarmstrong”the vent hole modification is working-put another 500 rounds through it and mag advance system is still working
this is the longest my rifle has worked since I received it. Happy,Happy,Happy
mine is the 22 cal 40 joule compact reg is set to 115 bar and I shorten the hammer spring about 1/4″
shoots 16grain AA 765 fps 60 shots per fill. Could go faster but I wanted it tuned down . great accuracy
………….Jarmstrong, sounds like you are where you want to be, I would like to get mine to shoot around 800 -820, = use less air, mine is accurate, just uses too much air, & bends the cocking arm…"jarmstrong"the vent hole modification is working-put another 500 rounds through it and mag advance system is still working this is the longest my rifle has worked since I received it. Happy,Happy,Happy mine is the 22 cal 40 joule compact reg is set to 115 bar and I shorten the hammer spring about 1/4" shoots 16grain AA 765 fps 60 shots per fill. Could go faster but I wanted it tuned down . great accuracy .............Jarmstrong, sounds like you are where you want to be, I would like to get mine to shoot around 800 -820, = use less air, mine is accurate, just uses too much air, & bends the cocking arm...
March 12, 2018 at 9:29 pm LinkRoger,
Did you test what speed it shoots after you backed out the spring?
Roger, Did you test what speed it shoots after you backed out the spring?March 12, 2018 at 9:43 pm LinkI can turn the reg up a little and easily get 800-820 fps
I strongly suggest that you get the vent hole drilled to prevent bending the cocking arm(the magazine advance lever)
I can turn the reg up a little and easily get 800-820 fps I strongly suggest that you get the vent hole drilled to prevent bending the cocking arm(the magazine advance lever)March 13, 2018 at 1:12 am Link“shutik”Roger,
Did you test what speed it shoots after you backed out the spring?…..No Shutik, sorry ,but my combro quit working, I am going to get some new batts to see if that is the problem, I t seems like it is still hot , don’t think it helped much, I would be ok with 40 shots , I am only getting 30 now.."shutik"Roger, Did you test what speed it shoots after you backed out the spring?.....No Shutik, sorry ,but my combro quit working, I am going to get some new batts to see if that is the problem, I t seems like it is still hot , don't think it helped much, I would be ok with 40 shots , I am only getting 30 now..
March 13, 2018 at 1:26 am Link“jarmstrong”I can turn the reg up a little and easily get 800-820 fps
I strongly suggest that you get the vent hole drilled to prevent bending the cocking arm(the magazine advance lever)……. ok,Thanks, Jarmstrong, I will try to do that the coming weekend ( busy w/other projects right now) , I just switched back to a couple of jacked up P-rods to tide me over for now, would defintly like to know what size & where to get a lighter spring to try.."jarmstrong"I can turn the reg up a little and easily get 800-820 fps I strongly suggest that you get the vent hole drilled to prevent bending the cocking arm(the magazine advance lever)....... ok,Thanks, Jarmstrong, I will try to do that the coming weekend ( busy w/other projects right now) , I just switched back to a couple of jacked up P-rods to tide me over for now, would defintly like to know what size & where to get a lighter spring to try..
March 28, 2018 at 12:36 am Linkdoes anyone have a working email for the Zbroia Kozak company ? I looked them up , but , couldn’t get the email to connect, I want to try to contact them for a Index Lever ( cocking lever ), I would really like to get my Zbroia working again , it has been down for over 2 weeks now, thanks , roger
does anyone have a working email for the Zbroia Kozak company ? I looked them up , but , couldn't get the email to connect, I want to try to contact them for a Index Lever ( cocking lever ), I would really like to get my Zbroia working again , it has been down for over 2 weeks now, thanks , rogerMarch 28, 2018 at 2:19 am LinkHave you tried any of these?
[email]export@zbroia.ua[/email]
[email]sale@zbroia.ua[/email]
[email]im@zbroia.ua[/email]
[email]sale@zbroia.ua[/email]Have you tried any of these? [email]export@zbroia.ua[/email] [email]sale@zbroia.ua[/email] [email]im@zbroia.ua[/email] [email]sale@zbroia.ua[/email]March 28, 2018 at 11:20 am LinkI used the export@zbroia.ua e-mail and I attached a photo of the broken part
Andrey is the man who handled all my requests
takes close to 2 weeks for parts to get to me
you might request another hammer spring that you could modifyI used the export@zbroia.ua e-mail and I attached a photo of the broken part Andrey is the man who handled all my requests takes close to 2 weeks for parts to get to me you might request another hammer spring that you could modifyMarch 28, 2018 at 12:08 pm Link“jarmstrong”I used the export@zbroia.ua e-mail and I attached a photo of the broken part
Andrey is the man who handled all my requests
takes close to 2 weeks for parts to get to me
you might request another hammer spring that you could modifyI’ve used the same email to communicate with Andy. Just be aware of 7 hours time difference between EST time.
"jarmstrong"I used the export@zbroia.ua e-mail and I attached a photo of the broken part Andrey is the man who handled all my requests takes close to 2 weeks for parts to get to me you might request another hammer spring that you could modify
I've used the same email to communicate with Andy. Just be aware of 7 hours time difference between EST time.March 28, 2018 at 12:45 pm LinkTalonTunes is also importing them but he is out at the moment. He’s hoping to have some in in a couple of weeks.
patTalonTunes is also importing them but he is out at the moment. He’s hoping to have some in in a couple of weeks. patMarch 28, 2018 at 12:56 pm Linkthanks guys, I tried a few times last night, email would not go thru, kept getting errors, anyway , I tried today & I didn’t get a postmaster failure, so I guess it is wait & see, roger
thanks guys, I tried a few times last night, email would not go thru, kept getting errors, anyway , I tried today & I didn't get a postmaster failure, so I guess it is wait & see, rogerMarch 28, 2018 at 12:58 pm Link“shutik”
“jarmstrong”I used the export@zbroia.ua e-mail and I attached a photo of the broken part
Andrey is the man who handled all my requests
takes close to 2 weeks for parts to get to me
you might request another hammer spring that you could modifyI’ve used the same email to communicate with Andy. Just be aware of 7 hours time difference between EST time……… hi Shutik, did you ever get a a moderator installed on your Zbroia ?
"shutik"
"jarmstrong"I used the export@zbroia.ua e-mail and I attached a photo of the broken part Andrey is the man who handled all my requests takes close to 2 weeks for parts to get to me you might request another hammer spring that you could modify
I've used the same email to communicate with Andy. Just be aware of 7 hours time difference between EST time......... hi Shutik, did you ever get a a moderator installed on your Zbroia ?March 28, 2018 at 1:21 pm LinkRoger,
I did not get it working. I’ve realuzed it is quite enough for me.
I would try to order replacement baffles from disyributor with threads for external moderator if I needed to make it more quiet.
Roger, I did not get it working. I've realuzed it is quite enough for me. I would try to order replacement baffles from disyributor with threads for external moderator if I needed to make it more quiet.March 29, 2018 at 8:04 pm LinkI wonder how many orders for a baffle set with a threaded outboard end it would take to get Donny to make them?
I would take oneI wonder how many orders for a baffle set with a threaded outboard end it would take to get Donny to make them? I would take oneMarch 30, 2018 at 4:40 am LinkI am busy making a complete new shroud and a silencer for my, it should all be done in a couple of weeks, as soon as I get all done I will post pics and all messurements here for those that might be interested in duplicate.
I am busy making a complete new shroud and a silencer for my, it should all be done in a couple of weeks, as soon as I get all done I will post pics and all messurements here for those that might be interested in duplicate.March 30, 2018 at 11:15 am LinkI just found out that Joe Brancato will be official importer and dealer for Zbroia company.
He will have parts as well.
I was trying to get 450 mm barrel ordered for my Kozak, as well as updated buffles with thread for external moderator. Joe took time to understand exactly what I need and gave me price right away.
He is discusding Zbroia on Facebook (PCP airguns and accessories) group.
I just found out that Joe Brancato will be official importer and dealer for Zbroia company. He will have parts as well. I was trying to get 450 mm barrel ordered for my Kozak, as well as updated buffles with thread for external moderator. Joe took time to understand exactly what I need and gave me price right away. He is discusding Zbroia on Facebook (PCP airguns and accessories) group.March 30, 2018 at 4:39 pm Link“shutik”Roger,
I did not get it working. I’ve realuzed it is quite enough for me.
I would try to order replacement baffles from disyributor with threads for external moderator if I needed to make it more quiet………….thanks , Shutik"shutik"Roger, I did not get it working. I've realuzed it is quite enough for me. I would try to order replacement baffles from disyributor with threads for external moderator if I needed to make it more quiet.............thanks , Shutik
March 30, 2018 at 4:43 pm Link“shutik”I just found out that Joe Brancato will be official importer and dealer for Zbroia company.
He will have parts as well.
I was trying to get 450 mm barrel ordered for my Kozak, as well as updated buffles with thread for external moderator. Joe took time to understand exactly what I need and gave me price right away.
He is discusding Zbroia on Facebook (PCP airguns and accessories) group……….Shutik, are you getting the 450mm barrel ? if so, can I ask how much ? also were you getting the larger air reservoir ? thanks , roger"shutik"I just found out that Joe Brancato will be official importer and dealer for Zbroia company. He will have parts as well. I was trying to get 450 mm barrel ordered for my Kozak, as well as updated buffles with thread for external moderator. Joe took time to understand exactly what I need and gave me price right away. He is discusding Zbroia on Facebook (PCP airguns and accessories) group..........Shutik, are you getting the 450mm barrel ? if so, can I ask how much ? also were you getting the larger air reservoir ? thanks , roger
March 30, 2018 at 5:36 pm LinkRoger, so far I’ve asked about longer barrel with longer shroud and replacement moderator monocore with 1/2 inch thread for external moderator.
Price for 450mm 177 barrel is $119.
I’ve decided to not get longer tube yet.
Roger, so far I've asked about longer barrel with longer shroud and replacement moderator monocore with 1/2 inch thread for external moderator. Price for 450mm 177 barrel is $119. I've decided to not get longer tube yet. -
Author
You must be logged in to reply to this topic.