Anyone have a .25 MP mold they want to sell or perhaps some .25 slugs made from that mold? Getting tired of shooting .25 jsb mk2 pellets
-Michael
-Michael
Upvote 0
Huben Hammerless K1
- Thread starter wlbryce
- Start date
Huben 0.25 has a very tight barrel, mp molds need to be reduced in diameter to 6.44 using a Sizer
Upvote 0
@schoofsbock thanks it did the trick.
Back up and shooting now.
I don't get it, thought only too much opening up of the powerwheel would make it blow air.
So
- powerwheel too much in = blowing all air untill cylinder is completely empty
- powerwheel too much out = blowing air (not sure if bleeds completely empty)
Can someone confirm this?
Here's my last group at 100m, almost no wind, shooting huben pellets at 290m/s (around 90joules) with reg pressure at 160bar.
Back up and shooting now.
I don't get it, thought only too much opening up of the powerwheel would make it blow air.
So
- powerwheel too much in = blowing all air untill cylinder is completely empty
- powerwheel too much out = blowing air (not sure if bleeds completely empty)
Can someone confirm this?
Here's my last group at 100m, almost no wind, shooting huben pellets at 290m/s (around 90joules) with reg pressure at 160bar.
Upvote 0
@jellvand, I can confirm your settings with the powerwheel. I`m not sure if it bleeds completely in any wheel position.
However, nice groups for 100m. Im far away from this after first time cleaning the barrel. Dont know what happened to my Huben. I`m also shooting the Huben slugs, but not better than with the JSB Beasts or redesigned Monsters !
Perhaps my groups are so lousy because I`m an old crazy a…hole shatterhand.
I will try this weekend again some settings with my Huben, hope the wheater will be fine.
However, nice groups for 100m. Im far away from this after first time cleaning the barrel. Dont know what happened to my Huben. I`m also shooting the Huben slugs, but not better than with the JSB Beasts or redesigned Monsters !
Perhaps my groups are so lousy because I`m an old crazy a…hole shatterhand.
I will try this weekend again some settings with my Huben, hope the wheater will be fine.
Upvote 0
Hey Schoofsbock I actually don't think this is a very good group just yet. Not sure what I can do to improve though... My previous huben s barrel was not aligned well with the magazine... This one has rifling in the magazine. Not sure how the transition from magazine to barrel is.
Upvote 0
Went out yesterday to test some swage ammo for my Huben 22 cal
I started with 12 different slugs that consisted of boat tails flat bases
hollow points and round nose solids and were 33 grains in weight ,
Here is a 50 yard group the one shot on the left was me I think
pulled the last shot I think I got excited . K-1 / V-4 I do not know
what speed I was shooting as I forgot the chronograph again .
I started with 12 different slugs that consisted of boat tails flat bases
hollow points and round nose solids and were 33 grains in weight ,
Here is a 50 yard group the one shot on the left was me I think
pulled the last shot I think I got excited . K-1 / V-4 I do not know
what speed I was shooting as I forgot the chronograph again .
Upvote 0
The swage slugs are made by me , here is a picture
of the 33 grain HP that were shot into some ballistic gel .
Upvote 0
so I just so I just got my 22 Huban. Jsb ammo sucks and the huben ammo was a 4 inch group at 100 yards. What molds did you use? And where did you get it D-RIG?
Upvote 0
This is not cast ammo it is made with a swage die
and pure lead wire , it is superior in every way to
cast ammo , it is perfectly round and the weight is
within 1/10 of a grain from slug to slug .
Upvote 0
@D-RIG, are you able to tell us something about your selfmade swagging kit please ? Some fotos, what kind of lead wire you use and from where you get it, dimension of your slug etc … ?
I`m also not satisfied with the Huben slugs and tested with many JSB with different fps etc. No way, I shoot the same groups with my SPA M10 with same distance.
The Impact X and the AA510 Extra FAC shows much better groups and I know the Huben is able to produce the same groups !
I`m also not satisfied with the Huben slugs and tested with many JSB with different fps etc. No way, I shoot the same groups with my SPA M10 with same distance.
The Impact X and the AA510 Extra FAC shows much better groups and I know the Huben is able to produce the same groups !
Upvote 0
for the Heavy jsb (18.13gr) to have a good performance he has to have the following specific measures: in the head 5.52 / 5.53 and in the skirt 5.64 to 5.7 and for this he will have to find specific batches.
Upvote 0
The swage die for the Huben are custom made from Corbin , The lead wire I purchase from
a person that I found oneBay it's around 3 dollars a pound .
The SPA M-10 is a great gun I've owned 2 of them and both were capable
of hitting a ping pong ball at 200 yards within 4-5 shots with swage ammo .
Upvote 0
I could not know which die you used from Corbin.
Can you please tell us winch one is it. or supply a direct link.
Thank you
Upvote 0
I can not make my own lead wire so I buy it extruded to a certain diameter of .185"
I buy my wire from a person on eBay he has a hydraulic press and sells the wire at
3.00 $ a pound , although he is not making wire at this time and I'm getting nervous .
Upvote 0