Finally got some time to shoot my nicest rifle (FX superior)

I've been working like crazy. I'm also inbetween homes, so have had little time or space to shoot. But I was able to make some time today. It's been a few months.

FX Crown Continuum MK1. Today I only used the 500mm superior .22 barrel and JSB hades. This barrel is a superlight variant, and has an epoxied carbon sleeve. I neglected to check my bottle pressure, and found it only had 100 bar in it. It is tuned for a 125 bar regulator setting. I didn't have the tool to swap my bipod over to my 580cc bottle, so left it as it was, since I wanted the luxury.

Almost all of my guns, when they fall off of the regulator, or drop in power, get drifting POI. Usually drifitng low left or low right as power falls off. This simply didn't happen with this barrel. I was still able to shoot with what was essentially pinpoint accuracy at 35 yards. Over maybe 35 shots my POI only dropped maybe .2" and did not drift left or right at all. This behavior seems to fall in line with this particular modified superior barrel being extremely accurate with any slug I've thrown at it. With no preferance or reguard to what tune I threw at it either. Basically the polar opposite of the .22 slug A liner I have. It just flat out performs, no matter what. Simply outstanding R&D on these.

Unfortunately I did not take any photos shooting. My phone doesnt take great pictures, and I didn't have it on me either. Victims were just some cans today. I set them behind a steel pipe, and sent a good number of ricochets into them off of the pipe (intentionally, for fun). The little 16gr hades were putting quite a dent in the pipe as well.

This gun normally shoots Hades @960fps out of the 380mm barrel. There is some port work that helps with this. The tune is extremely efficient for hunting with the short barrel. Adding a longer barrel with this tune increases power almost none.

DSCF5965.1631764462.JPG


500mm barrel below 
144966348_3876951552394948_4761830615413367284_n.1631764570.jpg

 
Thanks guys 😊



Yep, housing market is nuts right now. I'm looking to buy, but not like this.



I'm going to try and get more of my guns out this weekend if time allows. Got my 9 litre tank topped to 260 bar with my yong heng earlier this week. Also have a 600mm .30 caliber barrel I dialed in at 85fpe, but have not shot a single target with yet. 😎 First .30 airgun for me as well.



@biohazardman Normally with a new gun, I immediately have it in pieces and start inspecting/modifying/spiffing it up before I even shoot it lol. I used to be very good about shooting all my guns at least once every two days. It'll be the same again soon
 
Thanks guys 😊



Yep, housing market is nuts right now. I'm looking to buy, but not like this.



I'm going to try and get more of my guns out this weekend if time allows. Got my 9 litre tank topped to 260 bar with my yong heng earlier this week. Also have a 600mm .30 caliber barrel I dialed in at 85fpe, but have not shot a single target with yet. 😎 First .30 airgun for me as well.



@biohazardman Normally with a new gun, I immediately have it in pieces and start inspecting/modifying/spiffing it up before I even shoot it lol. I used to be very good about shooting all my guns at least once every two days. It'll be the same again soon


Oops I guess I lied again. I am a bad man. ;^) I am also guilty of tearing it down and making modifications before I even go out for my first shooting session.

I have an M3 coming soon and already purchased a new Superior Heavy liner, CF sleeve, Barrel Tuner and a trigger guard to put on it as soon as it gets here. It's really nice that I don't have to port the barrel inlet or probe cuz they already did it at the factory. Thanks FX
 
Nice rifle. I still want to get a Crown some day.

@Corvid_hunter Today is as a good a day as any! The earlier models are extremely potent with a little porting and tuning. Mine is a mk1 and comfortably outputs 50fpe with the 500mm superior barrel and 25gr .218 slugs (using a 7gm hammer weight)

I got lucky and found one for $1k flat which is actually where my Walnut stock came from. I sold it for $100 less, though as I needed money at the time more than I needed 2 Crowns. 

I'd even argue that build quality and overall finish might be higher on older models as they were not trying to mass produce them then.

@biohazardman Maybe Christmas will come early this year! I hope so for you, anyhow. It is pretty cool what fx is doing with their porting now. Though I'd still be inclined to touch it up, lol.