Join HERE
Daystate mct programmer?
Forums › PCP Airguns › PCP Airgun – Discussion › Daystate mct programmer?
-
Views : 1210 Likes : 0Likes : 0
-
June 12, 2018 at 9:34 am Link
So I just purchased the new daystate mct programmer seen on aeac’s video . And it comes with zero instructions. Has anyone found any kind of instructional information anywhere? I’m a little afraid I might do something wrong.
So I just purchased the new daystate mct programmer seen on aeac's video . And it comes with zero instructions. Has anyone found any kind of instructional information anywhere? I'm a little afraid I might do something wrong.June 12, 2018 at 11:08 am LinkHow much did u pay please and where
How much did u pay please and whereJune 12, 2018 at 11:13 am Link$400 from Precision airguns in Dryden Michigan I know he has a few more. And he’s a great guy and he did go through it with me as much as he could remember having been there at the event when it was launched but I I’m a little scared that I’m going to screw my gun up in some way I know it’s not that likely but if there’s a way to screw it up I can usually figure out how to do it.
$400 from Precision airguns in Dryden Michigan I know he has a few more. And he's a great guy and he did go through it with me as much as he could remember having been there at the event when it was launched but I I'm a little scared that I'm going to screw my gun up in some way I know it's not that likely but if there's a way to screw it up I can usually figure out how to do it.June 12, 2018 at 11:30 am LinkUnfortunately, it’s way too much to put into type. Especially, while I’m at work.
I plan on making a how-to video on programming but, have been backed up with other things. Maybe I’ll toss a quick guide together for you later this week.
One thing that is very important is to write down your default settings!
Serial #
HS
LS
Hi, Med, Low, Pulse Lengths
Mi, Med, Low, pressure points recorded in BITS
VoltsIf you adjust PL’s, adjust them all the same amount.
If you adjust pressure points, adjust them all the same amount.
HS and LS should remain the same after the adjustments.Unfortunately, it's way too much to put into type. Especially, while I'm at work. I plan on making a how-to video on programming but, have been backed up with other things. Maybe I'll toss a quick guide together for you later this week. One thing that is very important is to write down your default settings! Serial # HS LS Hi, Med, Low, Pulse Lengths Mi, Med, Low, pressure points recorded in BITS Volts If you adjust PL's, adjust them all the same amount. If you adjust pressure points, adjust them all the same amount. HS and LS should remain the same after the adjustments.June 12, 2018 at 11:41 am LinkThank you any little bit of help would be much appreciated. you’re a pretty cool cat
Thank you any little bit of help would be much appreciated. you're a pretty cool catJune 12, 2018 at 7:22 pm LinkI’m waiting for the new model which is supposed to be more for the shooter rather than dealers. I will accomplish the same thing but supposedly easier to use according to the dealer I got my Red Wolf from.
I’m waiting for the new model which is supposed to be more for the shooter rather than dealers. I will accomplish the same thing but supposedly easier to use according to the dealer I got my Red Wolf from.June 12, 2018 at 8:44 pm LinkWOW. I hope this is an over site.
WOW. I hope this is an over site.June 13, 2018 at 7:07 am LinkI hadn’t heard that Bryan maybe I should have waited too
I hadn't heard that Bryan maybe I should have waited tooJune 13, 2018 at 7:07 am LinkI did plug my Mark 4 into it last night and got a bunch of numbers to come up but without any instruction it just doesn’t make sense
I did plug my Mark 4 into it last night and got a bunch of numbers to come up but without any instruction it just doesn't make senseJune 13, 2018 at 7:09 am LinkJune 13, 2018 at 5:53 pm Link“tigerhunter”Thank you any little bit of help would be much appreciated. you’re a pretty cool cat
You’re quite a chubby chipmunk! LOL!!
"tigerhunter"Thank you any little bit of help would be much appreciated. you're a pretty cool cat
You're quite a chubby chipmunk! LOL!! :DJune 13, 2018 at 5:57 pm LinkYou should see me through a 24 Power Scope
You should see me through a 24 Power ScopeJune 14, 2018 at 6:54 am LinkI was always curious about the capabilities of the programmer. Please keep us posted on your journey @tigerhunter! It seems like Daystate is dropping the ball by over-charging and not providing any instructions to customers. If they don’t help you out with official manual, then you should consider looking at Heliboard.
I was always curious about the capabilities of the programmer. Please keep us posted on your journey @tigerhunter! It seems like Daystate is dropping the ball by over-charging and not providing any instructions to customers. If they don't help you out with official manual, then you should consider looking at Heliboard.June 14, 2018 at 9:11 am Link
Deleted Account…..
.....
June 15, 2018 at 11:19 am LinkBoy I would like to see that. Is it very large? You wouldn’t be interested in posting pictures of the pages here, would you?
Boy I would like to see that. Is it very large? You wouldn't be interested in posting pictures of the pages here, would you?June 15, 2018 at 11:26 am Link
Deleted Account…
...
June 16, 2018 at 9:39 am LinkOk thanx anyway. I’ll contact airguns of Arizona and see if they can send it to me
Ok thanx anyway. I'll contact airguns of Arizona and see if they can send it to meJune 16, 2018 at 2:04 pm Link“Brian10956”I’m waiting for the new model which is supposed to be more for the shooter rather than dealers. I will accomplish the same thing but supposedly easier to use according to the dealer I got my Red Wolf from.
Any idea when that new model is going to be released? Where did you hear about it if you don’t mind my asking.
Crusher
"Brian10956"I’m waiting for the new model which is supposed to be more for the shooter rather than dealers. I will accomplish the same thing but supposedly easier to use according to the dealer I got my Red Wolf from.
Any idea when that new model is going to be released? Where did you hear about it if you don't mind my asking. CrusherJune 16, 2018 at 4:51 pm LinkI’ve heard it from very good sources too. But, I think it will be a while. Maybe next year?
I've heard it from very good sources too. But, I think it will be a while. Maybe next year? -
Author
You must be logged in to reply to this topic.