These can come in 3x3, 4x4, 5x5, 6x6, and 7x7.
These are print to order, from high temperature plastic that will not warp if left in your car or truck on a hot summer day. They are slow printing so at this point I am selling at or below cost while I try to figure out how to get them to print faster without sacrificing quality.
These specifically are designed for the Benjamin 147 grain flat nose slugs, or any other .357 non-boat tail slug with a height less than 16.9 mm or 0.665", such as custom cast .357 bullets using the Lyman 356637 mold.
Cost is $25.00 for a 5x5 tray and lid for this height. $80 for four trays and four 5x5 lids. Other heights are possible. See my other classifieds for
Bottom view
Side view without lid:
These won't work for boat tails (I have another design that works for those, contact me if you're interested).
The following is for some custom cast 155 grain bullets that also fit in these trays, illustrating what the trays would look like in blue:
The following illustrates an earlier version that fit NSA 110 Grain Hallo Point dish base in black:
The following photo illustrates an earlier version in gray, for saboted all copper bullets that are not suitable for most PCP guns, used to illustrate the gray color only. It also illustrates a bullet lifter (sold separately) that lifts some or all of the bullets for use during scope sight in on a bench.
Shipping is $4.85 for USPS first class, or $9.85 for USPS priority mail.
Also, I am selling some NSA bullets that are too small for my modified bulldog, that also come with trays. See https://www.airgunnation.com/topic/wts-nsa-110-gr-hollow-point-dish-base-swaged-slugs-in-356-357-and-358/
Also I am selling some 85 grain NSA bullets with prototype trays because they are also too small for my modified bulldog. See https://www.airgunnation.com/topic/wts-griffin-357-dish-base-85-grain-hollow-point-with-containers
These are print to order, from high temperature plastic that will not warp if left in your car or truck on a hot summer day. They are slow printing so at this point I am selling at or below cost while I try to figure out how to get them to print faster without sacrificing quality.
These specifically are designed for the Benjamin 147 grain flat nose slugs, or any other .357 non-boat tail slug with a height less than 16.9 mm or 0.665", such as custom cast .357 bullets using the Lyman 356637 mold.
Cost is $25.00 for a 5x5 tray and lid for this height. $80 for four trays and four 5x5 lids. Other heights are possible. See my other classifieds for
Bottom view
Side view without lid:
These won't work for boat tails (I have another design that works for those, contact me if you're interested).
The following is for some custom cast 155 grain bullets that also fit in these trays, illustrating what the trays would look like in blue:
The following illustrates an earlier version that fit NSA 110 Grain Hallo Point dish base in black:
The following photo illustrates an earlier version in gray, for saboted all copper bullets that are not suitable for most PCP guns, used to illustrate the gray color only. It also illustrates a bullet lifter (sold separately) that lifts some or all of the bullets for use during scope sight in on a bench.
Shipping is $4.85 for USPS first class, or $9.85 for USPS priority mail.
Also, I am selling some NSA bullets that are too small for my modified bulldog, that also come with trays. See https://www.airgunnation.com/topic/wts-nsa-110-gr-hollow-point-dish-base-swaged-slugs-in-356-357-and-358/
Also I am selling some 85 grain NSA bullets with prototype trays because they are also too small for my modified bulldog. See https://www.airgunnation.com/topic/wts-griffin-357-dish-base-85-grain-hollow-point-with-containers