- The AGN App is ready! Search "Airgun Nation" in your App store. To compliment this new tech we've assigned the "Threads" Feed & "Dark" Mode. To revert back click HERE.
Wildcat shroud
- Thread starter Barbarian
- Start date
Tools Required:
• 3mm Metric Hex Key
Step 1 – REMOVE FORWARD CHEEK PIECE
There are two cheek rests on the Wildcat. Only the forward cheek rest needs to be removed in order to access the set screw that secures the barrel to the breech block. Using a 3mm hex key, remove the set screw securing the cheek rest to the breech block. Lift the cheek rest up and set aside.
Step 2 – REMOVE SET SCREW SECURING BARREL TO BREACH BLOCK
Using a 3mm hex key, remove the set screw securing the barrel to the breech and set aside
The set screw is located on top of the forward breach block.
Do not try removing the barrel yet as you need look in the screw hole to check the position of the circular indent on the brass end of the barrel. I suggest taking a picture circular indent now visible just inside the screw hole. When reinstalling the barrel, this circular indent must be in the same exact same position to ensure the barrel and transfer port are perfectly aligned and centered.
VIEW AFTER SCREW REMOVED SHOWING CIRCULAR INDENT ON BARREL
Step 3 – REMOVE THE BARREL
Grasp the end of the barrel near the muzzle and gently (and slowly) pull the barrel out of the breech. You may need to slightly twist the barrel slightly to get it started but once you feel the barrel move, pull the barrel straight out in a linear motion without any twisting. You want to keep the force constant yet slow as you don’t want to scratch any surfaces or cause damage to the O-rings.
THIS IS HOW THE BARREL WILL LOOK
CLOSE UP OF CIRCULAR INDENT USED AS A REFERENCE TO ALIGN BARREL PROPERLY
• 3mm Metric Hex Key
Step 1 – REMOVE FORWARD CHEEK PIECE
There are two cheek rests on the Wildcat. Only the forward cheek rest needs to be removed in order to access the set screw that secures the barrel to the breech block. Using a 3mm hex key, remove the set screw securing the cheek rest to the breech block. Lift the cheek rest up and set aside.
Step 2 – REMOVE SET SCREW SECURING BARREL TO BREACH BLOCK
Using a 3mm hex key, remove the set screw securing the barrel to the breech and set aside
The set screw is located on top of the forward breach block.
Do not try removing the barrel yet as you need look in the screw hole to check the position of the circular indent on the brass end of the barrel. I suggest taking a picture circular indent now visible just inside the screw hole. When reinstalling the barrel, this circular indent must be in the same exact same position to ensure the barrel and transfer port are perfectly aligned and centered.
VIEW AFTER SCREW REMOVED SHOWING CIRCULAR INDENT ON BARREL
Step 3 – REMOVE THE BARREL
Grasp the end of the barrel near the muzzle and gently (and slowly) pull the barrel out of the breech. You may need to slightly twist the barrel slightly to get it started but once you feel the barrel move, pull the barrel straight out in a linear motion without any twisting. You want to keep the force constant yet slow as you don’t want to scratch any surfaces or cause damage to the O-rings.
THIS IS HOW THE BARREL WILL LOOK
CLOSE UP OF CIRCULAR INDENT USED AS A REFERENCE TO ALIGN BARREL PROPERLY
Upvote 0
See below for an initial answer. I too would like to know, and am hoping we'll get more detail soon.
http://airgunnation.dev/topic/if-you-have-a-question-for-fx-post-it-here-and-i-will-try-and-get-it-answered/#post-37795
http://airgunnation.dev/topic/if-you-have-a-question-for-fx-post-it-here-and-i-will-try-and-get-it-answered/#post-37795
Upvote 0