What did you order / receive airgun related today? Thread

/me spinning in a not good way.
Awaiting permission to pick up a moderator, this can take as long as 3 month they say.

Denmark is one of the most digitalised countries in the world, so assuming their computer is up and running this should not take more than 30 seconds to find out.
1: guy have no criminal record
2: guy already have a permission for another moderator.
Send permission.

On a good note, i will soon have parts on the way for my 4 CYL Tuxing compressor ( piston rings for the 3 of the 4 cylinders that have that )

Taking it apart i was not really able to see where the hell the problem was, just know it will barely do 200 BAR pressure, and i need a full fat 300 BAR
 
  • Like
Reactions: Bandito
/me spinning in a not good way.
Awaiting permission to pick up a moderator, this can take as long as 3 month they say.

Denmark is one of the most digitalised countries in the world, so assuming their computer is up and running this should not take more than 30 seconds to find out.
1: guy have no criminal record
2: guy already have a permission for another moderator.
Send permission.

On a good note, i will soon have parts on the way for my 4 CYL Tuxing compressor ( piston rings for the 3 of the 4 cylinders that have that )

Taking it apart i was not really able to see where the hell the problem was, just know it will barely do 200 BAR pressure, and i need a full fat 300 BAR
I googled a 4 cylinder tuxing could you post a pic of it I can't seem to find one on the web
 
  • Like
Reactions: Bandito
it is pretty much a stone copy of the Coltri MCH6 compressor.

As the Tuxing " died" on me i now have both now, though Coltri compressor on gasoline engine..

The Tuxing compressor actually a lot cheaper now VS when i got it 2 years ago / 20 hours run time ago.
And it was cheap back then, at least VS a original Coltri compressor.

Mine is a 1 phase 230 V compressor ( that is normal mains here, but need 15 A fuse VS the 10 A normally used here )

I tapped into 1 phase of the high volt 3 phase at my friends house which all together is 400 Volts, but 1 phase just 230 volts and it is fused for more power so 15 A fuse )


PS: video filmed with same phone, so noise level should be comparable.
The electric Tuxing actually pretty low noice, you can easy have a conversation beside it.
The Honda motor on the Coltri you do not want to hang around for too long.




SUB 1000 USD on alibaba, 1500 USD on Amazon i think it is


PS: i have noticed on my fuse group in my apartment, it seem like light in my kitchen are also on 15 A fuse, so with a extension chord and if that 15 A also cover under cabinet wall sockets, i could run this on my balcony of the 2 floor apartment.
I could also tap into the power for the oven TBH i think that is also on the same 15 A fuses, at least there are 3 of them on the wall ( 3 phases )
 
Last edited:
Here's the electric version. $1065 (which included shipping) plus tax last June, Aliexpress.

my machine.JPG
 
it is pretty much a stone copy of the Coltri MCH6 compressor.

As the Tuxing " died" on me i now have both now, though Coltri compressor on gasoline engine..

The Tuxing compressor actually a lot cheaper now VS when i got it 2 years ago / 20 hours run time ago.
And it was cheap back then, at least VS a original Coltri compressor.

Mine is a 1 phase 230 V compressor ( that is normal mains here, but need 15 A fuse VS the 10 A normally used here )

I tapped into 1 phase of the high volt 3 phase at my friends house which all together is 400 Volts, but 1 phase just 230 volts and it is fused for more power so 15 A fuse )


PS: video filmed with same phone, so noise level should be comparable.
The electric Tuxing actually pretty low noice, you can easy have a conversation beside it.
The Honda motor on the Coltri you do not want to hang around for too long.




SUB 1000 USD on alibaba, 1500 USD on Amazon i think it is


PS: i have noticed on my fuse group in my apartment, it seem like light in my kitchen are also on 15 A fuse, so with a extension chord and if that 15 A also cover under cabinet wall sockets, i could run this on my balcony of the 2 floor apartment.
I could also tap into the power for the oven TBH i think that is also on the same 15 A fuses, at least there are 3 of them on the wall ( 3 phases )
Thanks for the reply
it is pretty much a stone copy of the Coltri MCH6 compressor.

As the Tuxing " died" on me i now have both now, though Coltri compressor on gasoline engine..

The Tuxing compressor actually a lot cheaper now VS when i got it 2 years ago / 20 hours run time ago.
And it was cheap back then, at least VS a original Coltri compressor.

Mine is a 1 phase 230 V compressor ( that is normal mains here, but need 15 A fuse VS the 10 A normally used here )

I tapped into 1 phase of the high volt 3 phase at my friends house which all together is 400 Volts, but 1 phase just 230 volts and it is fused for more power so 15 A fuse )


PS: video filmed with same phone, so noise level should be comparable.
The electric Tuxing actually pretty low noice, you can easy have a conversation beside it.
The Honda motor on the Coltri you do not want to hang around for too long.




SUB 1000 USD on alibaba, 1500 USD on Amazon i think it is


PS: i have noticed on my fuse group in my apartment, it seem like light in my kitchen are also on 15 A fuse, so with a extension chord and if that 15 A also cover under cabinet wall sockets, i could run this on my balcony of the 2 floor apartment.
I could also tap into the power for the oven TBH i think that is also on the same 15 A fuses, at least there are 3 of them on the wall ( 3 phases )
Thanks for the reply Peashooter.
With what I learned from you I was able to find it , and it can fill a 8.6L in 15 minutes. That's truly amazing , and Ali baba has one for $860. That flow rate of 100l a minute is great.
 
I received a 40 gallon tote that I found on sale at Wally world ( Walmart ) it was on sale for $20 , and 10 more gallons of distilled water , and a gallon of anti freeze. I bumped my compressors water supply from 10 to 20 gallons added the anti freeze to the mixture of existing Royal Purple Purple Ice. Filled my Guantlet to 4,500 psi in just a few minutes it only reached a
102°. I was filling my 6.8L when I heard a pop the little oil guage on the fill station adapter has a black plug on the top that popped out , and shot into the unknown , so I just removed that crappy little oil guage honestly the weakest part of that system , and replaced it with a female Foster quick connect. Now that fill station adapter is working great , and a lot stronger.
Filled that old Scott tank to 4,200 psi , and that Tuxing twin only reached 120°
 
Didn’t receive it today but just built this notos upgrade this weekend and took it out today. it’s basically the full build just waiting on the new cocking lever and hammer spring weight

pugs and pew pew two of my greatest pride and joys!

View attachment 565498
I love the build and the expressive look on your friend's face !
 
  • Like
Reactions: UhMerica
In my constant tinkering I got this today... Sniper 3x12FFP....from a discoveryopt 3x12HD FFP...why?
Well, even though the discovery is HD glass, and VERY clear, and the Sniper glass is decently clear, it was the center dot of the discovery that my old azz eyes had trouble focusing on! Plus the eye box is A LOT more forgiving on the Sniper (at 10-12 power) I tried to show it in the pics below (the center dot difference). When mounting on a Blitz, one has to be careful of which scope/ring height you want to mount, if you desire to use the extended mags...
IMG_3025.jpg
IMG_3035.jpg
IMG_3047.jpg
IMG_3033.jpg
IMG_3028.jpg
 
Thanks to some AGN members got a few things today. Some .510 slugs to test in the Element Max and this little beauty right here Lelya 2.0 .22 and BAT mod, BAT not installed in pics. Haven't had a chance to put a scope on and test it yet, but love the way it feels. My terrible pictures don't do it justice!
20250528_220553.jpg
20250528_220620.jpg
20250528_220741.jpg
 
Picked up the parts I dropped off for type 3 hard anodizing and they look great. Because of their minimum charge, I spent way too much on these two, but it was all I had ready and I was impatient to get them in the queue before leaving town for a few weeks. Haven’t put the trigger guard on the Wildcat because it evidently developed a leak I need to track down first.

Edited to add a picture of the reassembled but still leaking Wildcat. I mean, it was only two screws to put the action and stock together…
IMG_9827.jpeg


IMG_9831.jpeg


IMG_9830.jpeg
 

Attachments

  • IMG_9832.jpeg
    IMG_9832.jpeg
    2.9 MB · Views: 1
Last edited:
  • Like
Reactions: silverstreak
I love the build and the expressive look on your friend's face !
Didn’t receive it today but just built this notos upgrade this weekend and took it out today. it’s basically the full build just waiting on the new cocking lever and hammer spring weight

pugs and pew pew two of my greatest pride and joys!

View attachment 565498
That dog is , so cute, but watch out he is saying if you touch this airgun .
 
  • Haha
Reactions: coastal drifter