To get best MV..... try....
FX suggests a 30-40 bar difference between the 1st & 2nd regulator to allow adequate pressure fill.
*****
1. Open....valve adjuster max.. all the way out.....5+ rings
HS max to ~ #8
Micro to max... #1
2nd reg to 110
1st reg to~160
2. Shoot 5 shots to get MV... this will find the best 2nd reg pressure.
Want pellets 860-880
slugs. 960-980
3. Increase 2nd regulator until you reach 15-20 fps above your target speed.
Shoot 5 shots... get MV... adjust...
(This adjustment finds. the best amount of air. pressure to send the. projectile down the. barrel.)
The pressure adjustment can be INCREASED without removing the the air tank. .....but...... to decrease the pressure the air tank. MUST BE REMOVED....
The reg. adj. screw is. behind the trigger. Remove the trigger guard
with a 2.5mm Allen. wrench. The adj. screw is a
2.5mm head. Adjust. counterclockwise to
increase the pressure.
Very little rotation is
needed to alter the
pressure.
Press. now at 110...
adj. to 115..
The 2nd pressure guage
can be observed as the
screw is adjusted to
obtain the desired
pressure.
....replace trigger guard.
4. Adjust the HS (Max wheel) until the MV is a few fps above the desired value... shoot several shots to allow the gun to "settle in."
(This adjustment gives
the best HS pressure to
the projectile. )
5. Now adjust the Micro adjustment until the MV is on the desired value.
(This adjustment gives
fine tuning of the HS
tension.)
6. Close Valve adjuster (turn it in) until you notice it just starting to shave off
the last couple fps ... you want to end up at the desired fps for projectile.
Close the valve adjuster only 1/8 turn at a time.... very precise.
( The valve adjuster
regulates the time the air
port is open. By.
adjusting it down...
turning valve in and
finding the MV
decrease.... you adjust
the airflow to stop. when
the projectile exits the
barrel. This ensures the
projective exits the barrel
without deviation of flight
from too much airflow.)
7. Adjust 1st reg pressure to 30 bar above the 2nd reg. pressure.
( This will give adequate
pressure fill of the
plenum.)
WRITE DOWN THE SETTINGS
8. Now the gun can be sighted in!
FX suggests a 30-40 bar difference between the 1st & 2nd regulator to allow adequate pressure fill.
*****
1. Open....valve adjuster max.. all the way out.....5+ rings
HS max to ~ #8
Micro to max... #1
2nd reg to 110
1st reg to~160
2. Shoot 5 shots to get MV... this will find the best 2nd reg pressure.
Want pellets 860-880
slugs. 960-980
3. Increase 2nd regulator until you reach 15-20 fps above your target speed.
Shoot 5 shots... get MV... adjust...
(This adjustment finds. the best amount of air. pressure to send the. projectile down the. barrel.)
The pressure adjustment can be INCREASED without removing the the air tank. .....but...... to decrease the pressure the air tank. MUST BE REMOVED....
The reg. adj. screw is. behind the trigger. Remove the trigger guard
with a 2.5mm Allen. wrench. The adj. screw is a
2.5mm head. Adjust. counterclockwise to
increase the pressure.
Very little rotation is
needed to alter the
pressure.
Press. now at 110...
adj. to 115..
The 2nd pressure guage
can be observed as the
screw is adjusted to
obtain the desired
pressure.
....replace trigger guard.
4. Adjust the HS (Max wheel) until the MV is a few fps above the desired value... shoot several shots to allow the gun to "settle in."
(This adjustment gives
the best HS pressure to
the projectile. )
5. Now adjust the Micro adjustment until the MV is on the desired value.
(This adjustment gives
fine tuning of the HS
tension.)
6. Close Valve adjuster (turn it in) until you notice it just starting to shave off
the last couple fps ... you want to end up at the desired fps for projectile.
Close the valve adjuster only 1/8 turn at a time.... very precise.
( The valve adjuster
regulates the time the air
port is open. By.
adjusting it down...
turning valve in and
finding the MV
decrease.... you adjust
the airflow to stop. when
the projectile exits the
barrel. This ensures the
projective exits the barrel
without deviation of flight
from too much airflow.)
7. Adjust 1st reg pressure to 30 bar above the 2nd reg. pressure.
( This will give adequate
pressure fill of the
plenum.)
WRITE DOWN THE SETTINGS
8. Now the gun can be sighted in!