Streloc Pro app - scope settings

[bigHUN]

I want to start using this app, I understand what it means to "measure and input scope height" meaning if the scope is mounted parallel to the barrel, but

where to measure if I am using adjustable scope rings? At the front lens centerline? in the middle of the scope length CL? at the turrets CL?

If the app would take the angle as a value that would be much easier =arc tg b/a

 

[OldSpook]

Measure the front ring at the split and the back ring at the split from the center of the bore. Average the two measurements. That will be close enough. Your line of sight is never parallel to the bore anyway.

 

[Vrodfast]

It’s the center of the scope to the center of the barrel. What I do is measure the outside diameter of the scope and the barrel. Divide those in half and add those together with the distance between them. 
1/2 scope diameter + 1/2 barrel diameter + distance between = scope height. 

 

[qball]

Measure the best you can from the objective lens to barrel, it’s really not that critical to be off 1/10th if an inch. 

 

[Guest]

Measure the front ring at the split and the back ring at the split from the center of the bore. Average the two measurements. That will be close enough. Your line of sight is never parallel to the bore anyway.

 

[bigHUN]

Measure the front ring at the split and the back ring at the split from the center of the bore. Average the two measurements. ...

^ This what I needed to know. Regardless of FFP or SFP the reticle is not etched on the front lens but somewhere inside the inner tube length. I believe this would be a closest number.

Yes I am well inclined with instruments and tools I can get it precisely. THX

 

[Airgun-hobbyist]

Keep in mind, after getting the closet measurement that you can, you can alter the numbers so that the point of Impact is comparable to the app. I have found that this "altering" of the numbers is needed to perfect the App's figuring of ballistics to make both the gun and the app coincide.

 

[bigHUN]

I have filled the fields for my gun (.25 Impact PP 700), the scope height 8.13 cm (1 mm slope with adjustable rings between front and rear ends, and btw why cm why not mm?), the pellets (25 cal JSB MK2 33.94gr), the speed (918 fps), the rifling twist rate (27),

Now what next? I watched some youtube videos, every person who posted is running through the menus and buttons what the app can do (tons of things), but I have not seen any life sample what to do with this?

In example I have a brand new scope, I will need to get on paper and sight in @ 50 and zero my scope. (the X50 is calibrated at 50 meters with x25 power) This is fine for now. But...

Now I need a number for hold-over (my scope is a SFP) to get on paper @ 100, and next a hold-under for 20.

I don't see anywhere a sample txt or video How-To calculate my clicks based on input data? Which Tab in the app will give me these click or at least inches/cm?

(this Falcon X50 reticle is calibrated at 100 meters with x25 power) and onse setup I will be riding turrets vs holdovers.






Yes I understand the "fine tuning on the fly", we had to do that all the time with archery software's in order to print sight tapes.

 

[JungleShooter]

Are you on apple or android?

I can walk you through this step by step. PM me. 

Options: I can call you or send you a video conference link (Zoom).

Matthias

 

[bigHUN]

Are you on apple or android?

I can walk you through this step by step. PM me. 

Options: I can call you or send you a video conference link (Zoom).

Matthias

I am with droid and PLEASE pm me any time, I just got home from my range.

I will need a "how to" probably early next week. My gun and the scope was completely apart to bits and pieces, 

I will need to put these things to a starting perspective (get on paper and scope rail alligned to a barrel) at least one day, and a full sighting-in distances probably to leave for a next day with fresh mind to go.