I have a notos .22 fully upgraded to a fx liner carbon fiber barrel. Brass valve with 4mm opening, hammer weight. Plenum and plenum extemsion from c88. And i recently upgraded my air tank to 2 oem notos air tanks put together. But as soon as i got them in, my magazines started jamming, not sure what could be happening. It cycles 2 or 3 pellets and then jams. Any help?
Umarex Notos not feeding
- Thread starter lopezvega95
- Start date
I'd suspect that you have a loose barrel.. mine came that way from the factory..
so there's I believe 2 screws that you take out on the top of the receiver that holds the shroud on.. under one is a Allen set screw or as some people say grub screws.. mine was loose and I actually had a crumbled o ring that goes around the barrel.. got new one from firewalker here on AGN.. and I forgot exactly what I did, I don't remember drilling the receiver, but I likely tapped the second hole all the way through for 2 set screws.. and I did drill a little hole in the shroud to put the Allen key in to tighten up the extra screw.. if you don't have a extra screw, it's a 4mm x 6 mm if I remember correctly..
Mark
so there's I believe 2 screws that you take out on the top of the receiver that holds the shroud on.. under one is a Allen set screw or as some people say grub screws.. mine was loose and I actually had a crumbled o ring that goes around the barrel.. got new one from firewalker here on AGN.. and I forgot exactly what I did, I don't remember drilling the receiver, but I likely tapped the second hole all the way through for 2 set screws.. and I did drill a little hole in the shroud to put the Allen key in to tighten up the extra screw.. if you don't have a extra screw, it's a 4mm x 6 mm if I remember correctly..
Mark
Upvote 0
another possibility is that the magazine screw is too tight and just needs loosen a little bit.
Mark
Mark
Upvote 0
I have already removed the barrel and re tighten it several times, i will have to remove the second air tank to se if that is the issue, maybe creating presure against the barrel or something
Upvote 0
I tried several magazine, oem and 3d printed same issue, so its probably a barrel misaligned or something, ill check this weekend and see if the second tank is the issue
Upvote 0
The pellet probe has a lot of slop in it, Not sure how to tighten it up, Take the magazine out and fill the probe it slides back and forth, I have used some heat shrink tubing on mine that help a lot but didn't last long, Some pellets work better than others ,
Mike
Mike
Upvote 0
I know this is the PP700 but it's the exact same as the NOTOS just the opposite side.
Pay attention to the small bits and where they go. Especially orientation.
Hope it helps.
Pay attention to the small bits and where they go. Especially orientation.
Hope it helps.
Last edited:
Upvote 0
Did you get your problem figured out? I'm new to all this need to get my 10 post or whatever in it's been past the 10 days....but I do have a question for you where did you get your liner? This is my first PCP mod got some stuff from C88 aclways shot a springer...never going back lol. Anyway thanks and have a great weekend!
Upvote 0
I bought the kit separately because together is like 350.
Fx liner from Utah airguns https://utahairguns.com/product/fx-stx-superior-liner/
And the barrel kit from c88
Umarex Notos FX Barrel Kit (500mm/600mm) .22/.25cal
FX barrel kit designed to fit the Notos. This kit will allow you to utilize 500mm FX liner in .22/.25cal which you will need to provide. The kit comes with everything needed besides the liner. There is no modification needed and is a simple swap. Spare orings/set screw will be included. These...
c88-air.com
Fx Barrel kit with harmonic dampening rings for Umarex Notos
Looking to improve accuracy and get more power out of your Umarex Notos? Well this kit will do that! Choose between a 380 mm length or 500 mm length barrel, the 380 will be shorter and more compact. While the 500 will give you a slightly better accuracy and power, but longer and heavier. This...
terminadorindustries.com
Yeah you get the rings for harmonic dampening but its really not a difference, my notos shoots to 100 yards easy, I have also upgraded the brass valve and have a plenum so that all helps out
Also check out buckrail, for 3d printed items.
Upvote 0