Help Please ! O-Ring size

[kayaker]

Dah forgot for a 22cal; puncher Breaker

Need help finding the size of the two o-rings that goes on the power adjustment valve . Thanks in advance

 

[Odoyle]

If it's THIS I think it's 4mm ID and 6mm OD.

Troy Hammer Annihilatior is the one who would know for sure. Maybe JimNM if he took his apart or maybe MscottLeeman.

 

[kayaker]

Odoyle that's the ones maybe one of them will chime in or I'll send a P.M. I'll try to measure mine tomorrow . Thanks a bunch ! Darell

 

[pnwairgunner]

You can also check captainoring.com and see if he is selling complete o ring kits for it.

 

[kayaker]

pnw thanks for the suggestion but they do not have a kit

 

[kkarmical]

Just pulled mine and tried the smallest oring I have on hand 1.5mm x 3mm N70 and it is too large, I thought for sure I had used these.

 

[thammer]

Metric orings I believe go by the interior diameter and then the oring thickness. That makes them 3 x 1.5mm but the OD is 6mm and the ID is 3mm. 



Edit: It's actually opposite. 

Thickness x ID

1.5mmx3mm is the size. 

 

[rcorwin3]

I would go on Ebay or Amazon and get the assorted o-ring kits. They come in both ASE and Metric sizes as well as different types and grades. Also not real expensive.

Good luck.

rik

 

[ALARM890]

Kral Puncher Breaker Seals [ 22 cal.]

2 – tank seals ( -214 )

1 – gauge seal ( 2mm x 16 mm )

2 – power wheel ( 1.6mm x 3.1 mm )

2 – air transfer ( 2mm x 16 mm )

1 – breech ( -009 )

 

[30harry]

Metric orings I believe go by the interior diameter and then the oring thickness. That makes them 3 x 1.5mm but the OD is 6mm and the ID is 3mm. 



Edit: It's actually opposite. 

Thickness x ID

1.5mmx3mm is the size.

Would those be different for 25 cal? Info I have says they are 1.6mm x 3.1mm??

 

[kayaker]

Just pulled mine and tried the smallest oring I have on hand 1.5mm x 3mm N70 and it is too large, I thought for sure I had used these.

Metric orings I believe go by the interior diameter and then the oring thickness. That makes them 3 x 1.5mm but the OD is 6mm and the ID is 3mm. 



Edit: It's actually opposite. 

Thickness x ID

1.5mmx3mm is the size.

kkarmical thanks for the P.M. & all your help Almost done LOL

thammer thankyou sir

 

[kayaker]

I would go on Ebay or Amazon and get the assorted o-ring kits. They come in both ASE and Metric sizes as well as different types and grades. Also not real expensive.

Good luck.

rik

Going to send my old ones in & have measured then I will be positive of the exact size then buy them in BULK

 

[kayaker]

Kral Puncher Breaker Seals [ 22 cal.]

2 – tank seals ( -214 )

1 – gauge seal ( 2mm x 16 mm )

2 – power wheel ( 1.6mm x 3.1 mm )

2 – air transfer ( 2mm x 16 mm )

1 – breech ( -009 )

may I ask where you found those sizes , some differ from mine

 

[kayaker]

. 



1.5mmx3mm is the size.

Would those be different for 25 cal? Info I have says they are 1.6mm x 3.1mm??

P.A. sent me a seal kit last year , just know need it , but did not get all the o-rings . They are to get ahold of me next Monday so I'll try to find out for you .

 

[ALARM890]

Air Venturi / Importer