First PCP: BSA R10 SE and compressor. Anything else I need to consider?

Jump to latest Follow Reply
K

kevin1

Member
Oct 25, 2020
35
1
TX, United States
I placed an order for my first PCP rifle. It’s a BSA R-10 SE walnut stock in 0.177. I have also a Benjamin traveler compressor that’s on its way.

I already have scope/mount/cleaning supplies/pellets (planning to shoot JSB 10.34gr).

I read that the instructions that come with the gun are pretty light. That’s why I’m asking here. Is there anything else I need to consider? Do I need a special adaptor for the compressor? Do I need to do any type of maintenance (any sort of special lube, or barrel cleaning for example) on the gun when new and after shooting?

This is my first PCP and I’d like to do things correctly.


 
I had an R10 SE in .177 and it was very accurate. I can’t remember if it had a fill probe or foster, but if it has a probe you will need an an adapter to screw on the probe to accept the foster on your compressor. You might want an extra mag and a single shot loader. I got rid of mine because I have small hands and the stock is a little thicker on the r10. They tend to be long but you can shorten it by taking off the shroud and screwing on a Donny FL. Have fun with it and post pics when you get it. It is just the beginning of a journey down a deep rabbit hole. 
 
Upvote 0
Kevin that's a heck of a way to start! A first rifle you'll keep forever. I second the suggestion for the bsa single shot trey, swings out and easy to load with nice "clickiness"

As for your rings, BSA's dovetail rail is a little wider than other brands, and some rings don't fit so well. BKL rings are the way to go if yours dont work out.

PS If you don't like that walnut stock and prefer the look of the black soft touch, I have a brand new black soft touch stock I'd work a deal for a walnut. Just planting a seed- I know its wishful thinking!
 
Upvote 0
Yes…. I’m starting big…..My goal, down the road, is to replace some of my 22lr shooting at 50Y with a PCP and to shoot in my backyard at 30Y. I had to start big because this rifle will be compared to my Anschutz 1710HB and Vudoo. With Center X They both shoot in the 0.2s (low 0.2s for Vudoo and mid to high 0.2s for the 1710). I don’t think the BSA will be as accurate, but I’m hoping to get similar accuracy as what I get when shooting SK+ (low 0.3s) at 50Y in a calm day.



The rifle already comes with 2 mags. What’s the benefit of the single shot tray? Is it because the mag deforms the pellets?

BTW, I’m keeping the walnut stock 😊. It was 50% of why I went this model. I really hope I’ll get some nice grains….
 
Upvote 0
I’ve owned an R10 mk2 for a couple of years now. Shoot HFT with it. You will need a foster fill adapter for the fill probe. Mine did not shoot the JSB’s worth a darn. H&N 10.65 4.50 (not 4.52’s) Baracuda Match shot like a laser. 890 was the speed they preferred. Single load adapter will tighten up the groups as well. 

as bvc stated, it is a forever gun. I’ve been offered more than I’d paid for mine. if you ever tire of it, let me know😉


 
Upvote 0
I've never heard of BSA mags deforming pellets, they are just expensive at 50 bucks each. I suggest the SST because it works really well and makes for a different shooting experience. I find it more relaxing as it makes me take my time

There are schools of though that since the BSA mag holds the pellets under tension, the probe is pushing them into the barrel a little catty-whompus. I have not noticed any accuracy deficiency with my r-10 using a mag.










 
Upvote 0
I have a TX200 in 0.177 that likes JSB 10.34. But I have many other type of pellets I bought to try with the TX200. That’s one of the reasons I went with 0.177 for the BSA rifle.

Thanks for the link to HAM site. It does complain about the incomplete instruction manual and that’s one of the reasons I posted here.... to make sure I won’t miss any important points.
 
Upvote 0
Upvote 0
Your new gun does not have open sights so you will need A scope and proper mounts and be sure to measure if it's 11mm or 13mm before ordering the dovetail rings. Ask the knowledgeable dealer if it's 11mm or 13mm for sure. You may want to go with adjustable or droop compensating mounts to not run out of elevation clicks on your scope too due to barrel droop typical with most airguns unless you want to bend your barrel up and not spend extra for adjustable or droop compensating mounts (nothing wrong with bending barrels on brand new guns even AZ does it and advocates it). Mounts dependant on your dovetail rail size.

Read up in the optics section to help with your scope buying decision based on your budget and if total brightness and total clarity throughout the entire range all the way to max zoom power is important to you or not and non critical eye relief throughout the entire zoom range and generous eyebox and big sight picture.


 
Upvote 0
Silicone Oil and Silicone grease for Maintaining parts and O-rings in the High pressure areas of the gun

I use these

https://www.amazon.com/Team-Losi-Silicone-Shock-100wt/dp/B00B9E9AJS/ref=sr_1_13?dchild=1&keywords=silicone+shock+oil&qid=1603732780&sr=8-13

https://www.amazon.com/Trident-acc577-Silicone-Grease-2oz/dp/B0000DCVZL/ref=sr_1_5?dchild=1&keywords=silicone+grease&qid=1603732912&sr=8-5
Click to expand...

Thanks for the links.

Can you please elaborate on this? I already have the Crossman silicone chamber oil. Is that the same thing as silicone oil? Is it only for the O-rings?

I also have various other products for powder rifles. That includes Ballistol as well as TW25B grease. Would this grease suffice or I need a silicone grease? If so, how to I use it.
 
Upvote 0
Order a chronograph unless you like chasing your tail
Click to expand...

That's a great advice. A few month ago, I was tuning my TX200 and bough a ProChrono DLX. I also have a MagnetoSpeed sporter for load development, but I'm not it will work on the the BSA.

BTW I already have the scope and mount. It's a Hawke Vantage 4-12X40 AO and a UTG PMTOWL-A Dovetail to Picatinny/Weaver Rail Adaptor Mount.
 
Upvote 0
I got the gun today. It's empty and the compressor won't arrive before Monday.

I guess I'll use that time to Clean the gun (mainly inside the barrel) with Ballistol and Otis pull-throughs. 

I dry fired a few times. The trigger is decent and breaks at just below 2lbs. I might try to adjust it and make it lighter.



I didn't win the wood lottery, but the woodwork on the gun is really nice. It's definitely on par with a $2k PB rifle (haha...first time I use the word PB. Didn't know what it meant until yesterday :) )

The metal work, on the other hand, looks cheap. It's nowhere near a nice bluing. At the same time I don't have any other PCP, so maybe that's how the metal is supposed to be. BTW on bluing ....the two best bluings that I have amongst my guns are a TX200 and a vintage Rem 700 Varmint Special. The bluing on the TX200 is even superior to my new Anschutz 1710.



Here's a pic of the gun:


 
Upvote 0
You must log in or register to reply here.
Top Bottom
Back
Home
Forums
Resources
Menu