edgun Rm5 long plus donnyfl ronin just got freaky quiet !!

[Smilewiper]

 

[bolo]

.25?

 

[Smilewiper]

yes

 

[8thman]

I have found with my Edgun r5m 22cal is very quiet. But as the shooter it is louder because the hammer is right below the ear. When i let a friend shoot it and I’m just to the side the gun is very quiet. But I have no problem believing that with more suppression that if I were sitting next to you I would notice a difference, with and without the added Donny.

 

[Peskådot671]

I have found with my Edgun r5m 22cal is very quiet. But as the shooter it is louder because the hammer is right below the ear. When i let a friend shoot it and I’m just to the side the gun is very quiet. But I have no problem believing that with more suppression that if I were sitting next to you I would notice a difference, with and without the added Donny.

I also let a friend shoot my R5M Standard in .25cal and I was 5 feet away from him. I was very surprised at how quiet it was considering it's a .25cal in stock configuration. I can only imagine how much quieter it is with the Ronin attached.

 

[Smilewiper]

well this a .25 and I am shooting jsb 25.39 @ 945 fps so it's crack'in ,not backyard friendly to me so I slapped a ronin on it and it made a huge improvement

and my groups got a little better also !

 

[Peskådot671]

well this a .25 and I am shooting jsb 25.39 @ 945 fps so it's crack'in ,not backyard friendly to me so I slapped a ronin on it and it made a huge improvement

and my groups got a little better also !

Well, that's a plus. 

 

[bckyrdsnpr52]

Did Donny make the adapter? I haven't seen them before.

 

[Elbowgrease]

I put a DonnyFL Tatsu on my Lelya .22. I was not overly impressed but it did help some. Also to bckyrdsnpr52. You can get the adapter from EdGun west. Its an entire baffle replacement with the threaded end on it.

 

[qball]

I put a DonnyFL Tatsu on my Lelya .22. I was not overly impressed but it did help some. Also to bckyrdsnpr52. You can get the adapter from EdGun west. Its an entire baffle replacement with the threaded end on it.

Try a sumo!

 

[Dingfelder]

Yeah Tatsu is either the smallest or about the smallest.

 

[Blackpaw]

next to smallest I think. I think the Tanto is the smallest.

 

[ghoststalker]

Why not the “ bat” from edgun ? 

 

[Elbowgrease]

I thought about the bat but did not want to add the little bit of length. The DonnyFL can be removed much quicker then the bat can. I have been tempted because I have been hearing so much good about it. As far as the Tatsu, I do believe it is Donny's smallest. I do have a newer Ronin with the changeable threaded end on my Vulcan. Also have a Sumo for the Vulcan but it is one of the older ones that cannot have the ends swapped out. Might have to swap to the sumo on the Vulcan and get the different end for the Ronin.

 

[Peskådot671]

If you get the Bat, you're only adding about 2 inches to the total length because all you're doing is switching out the second half of the moderator. Not adding to it. The factory baffled section is approximately 4.25". The Bat is 6.25".

 

[BlackICE]

Before buying an LDC or bat try doing this.



https://www.airgunnation.com/topic/edgun-25-r5m-vs-marauder-25-sound-comparison/