Does anyone know the size of the first generation matador pellet probe orings? Can’t find anything on edguns website or edgun west either for the older versions.
thank you,
erik
thank you,
erik
Edgun matador first gen pellet probe oring help
- Thread starter hegshen
- Start date
Brians site Edgun West has a listing of all the O-rings on his website. Go to resources, then manuals, down below manuals for O-rings For 25 cal it is 6 x 2 mm. 30 cal 7 x 3 mm
Upvote 0
Matador R2.5 O rings
2,57 х 1,78 (005) – 1 pc (front plug filling valve)
2.5 x 1 -2pcs (.177) 3 x 1 (.22) 4 x 1 (.25) – R2.5 and R3 Pellet probe
9 х 1.5 – 1 pc Rear of the regulator piston
25 х 3 – 4 pcs Front and rear cyl plugs, regulator/valve body
5 х 2.5 – 1 pc Pressure gauge
5 х 1.5 – 5 pcs Front of the regulator piston x1, regulator adjustment screw x1, .22cal transfer port, x1, fill probe x2
7 x 1.5 – 1pc Barrel to breech
Matador R3 O rings
2,57 х 1,78 (005) – 1 pc Front plug filling valve
2.5 x 1 -2pcs (.177) 3 x 1 (.22) 4 x 1 (.25) 5.1 X 1.6 mm or 008 (.30 Gen 1) – Pellet probe
7 х 1.5 – 1 pc Gen 2 .30cal breech
20 х 3 – 1 pc Gen 1 .30cal front regulator body
9 х 1.5 – 1 pc Rear of the regulator piston
19 х 2 – 1 pc Suppressor seal
25 х 3 – 4 pcs Front and rear cyl plugs, regulator/valve body
5 х 2.5 – 1 pc Pressure gauge
5 х 1.5 – 5 pcs Front of the regulator piston x1, regulator adjustment screw x1, .22cal transfer-port, x1, fill probe x2
I wasn't sure what you meant by first-generation Matador, the R2 is the first one in the USA
2,57 х 1,78 (005) – 1 pc (front plug filling valve)
2.5 x 1 -2pcs (.177) 3 x 1 (.22) 4 x 1 (.25) – R2.5 and R3 Pellet probe
9 х 1.5 – 1 pc Rear of the regulator piston
25 х 3 – 4 pcs Front and rear cyl plugs, regulator/valve body
5 х 2.5 – 1 pc Pressure gauge
5 х 1.5 – 5 pcs Front of the regulator piston x1, regulator adjustment screw x1, .22cal transfer port, x1, fill probe x2
7 x 1.5 – 1pc Barrel to breech
Matador R3 O rings
2,57 х 1,78 (005) – 1 pc Front plug filling valve
2.5 x 1 -2pcs (.177) 3 x 1 (.22) 4 x 1 (.25) 5.1 X 1.6 mm or 008 (.30 Gen 1) – Pellet probe
7 х 1.5 – 1 pc Gen 2 .30cal breech
20 х 3 – 1 pc Gen 1 .30cal front regulator body
9 х 1.5 – 1 pc Rear of the regulator piston
19 х 2 – 1 pc Suppressor seal
25 х 3 – 4 pcs Front and rear cyl plugs, regulator/valve body
5 х 2.5 – 1 pc Pressure gauge
5 х 1.5 – 5 pcs Front of the regulator piston x1, regulator adjustment screw x1, .22cal transfer-port, x1, fill probe x2
I wasn't sure what you meant by first-generation Matador, the R2 is the first one in the USA
Upvote 0