EDgun Edgun Leshiy 2

[Glem.Chally]

I'd try to get a flathead screwdriver a size so it just barely catches that outer part of the brass and slides inside the brass bit. Then gently drive it down so it bottoms out inside there.

It shouldn't be that tight so it just needs a bit of help. Just be careful because if you put it in there like a wedge it'll make it tighter. 

^^ This won't make any dust or pieces and if it doesn't work no harm done.

Another thing you could do is get a drop of JB weld on a very small bolt or something and stick it to the bottom of the brass part upright. Let it cure and try to back the bolt out hopefully taking the brass bit with it.

^^ These are both assuming the lowest brass bottom is part of what broke off. 

Or an easy-out (but gotta be on your A game with that.

 

[ProkAM]

Today I made slug hades for Leshy )

https://youtu.be/MHmruondJ7E

 

[Hobbyman2007]

Nathan, the shot count is with the original tubes installed. I’ll run a full string to see how many shots I get from a 250bar fill. I was getting 5 mags worth on the regulator prior to changing the jets.

what cal was that? my .22 L2 is still in the "out of box" condition and whatever is a factory tune 3 mags can go before drop the reg

Sorry about the misinformation . From factory was getting three magazines on the regulator with a 300 bar fill. With the 350cc bottle and a 250 bar fill was 5 magazines. It’s a .25 caliber. These rifles sure like a lot of air . 


For removing broken fittings like the jet , I’d try a Torx bit , gently tapped into the brass. I’ve used them through my career as a mechanic for years . There’s a slight taper to them so they really bite well into soft metals like brass or aluminum. 

 

[yenniedn]

Thank you, Glem & Hobby . . . I was thinking along those lines but don't have many tools small enough to try to tap into the broken brass threads. Will be dropping it off later today to local friend with more tools, patience and skill than I have for extraction attempt. Thx

 

[RAMJET66]

find a correct sized EAZY OUT slightly tap it in , & it turn counter clock wise, neen using them for decades, good luck..

 

[Cranky1]

I’ve used the torx trick on carb jets before and it’s almost always worked…. When it didn’t I went to a left handed drill bit, slow and easy. 

 

[bckyrdsnpr52]

That's all good but without showing how they group, after smashing them, what's the point?

 

[Jack.K]

Got it out. The Torx T-7 did the trick. 

 

[jamoalla]

When I am shooting slugs, I don’t remove the magazine from the gun. I take off the back plate and load, then replace the back plate, much like loading a revolver except the back plate.

Thanks !

 

[Glem.Chally]

Got it out. The Torx T-7 did the trick. 

Nice work!

 

[yenniedn]

@jack.k is seriously the best! Thank you so much for the advice from the forum and to Jack for his awesomeness!

 

[theLBC]

so here is the pressure/velocity chart from the edgun video for the 5.5 or .22 350mm.

i was under the impression that 130bar from the factory would produce ~915fps or higher, and this seems to say different. anyone know what the stock pressure and velocity are when shipped from EGW?

 

[Rhinolow]

i was under the impression that 130bar from the factory would produce ~915fps or higher, and this seems to say different. anyone know what the stock pressure and velocity are when shipped from EGW?

Depends a lot on the grain of the pellet

 

[Cranky1]

so here is the pressure/velocity chart from the edgun video for the 5.5 or .22 350mm.

i was under the impression that 130bar from the factory would produce ~915fps or higher, and this seems to say different. anyone know what the stock pressure and velocity are when shipped from EGW?

Mine stock from egw don’t know what reg was at 440ft elevation

Granted this gun is 22 cal 350mm Alfa with huma mod 40…. Kat40 from egw. Just got it Friday so it’s still breaking in but it has grouped pretty good at 40 for a guy that is just a decent shot. 

 

[theLBC]

so here is the pressure/velocity chart from the edgun video for the 5.5 or .22 350mm.

i was under the impression that 130bar from the factory would produce ~915fps or higher, and this seems to say different. anyone know what the stock pressure and velocity are when shipped from EGW?

Mine stock from egw don’t know what reg was at 440ft elevation

Granted this gun is 22 cal 350mm Alfa with huma mod 40…. Kat40 from egw. Just got it Friday so it’s still breaking in but it has grouped pretty good at 40 for a guy that is just a decent shot.

thanks! i have similar .22/350mm with the mod40 and i have only been shooting some flavor of 18.13gr jsb that eduard is using in his demos.

 

[Glem.Chally]

Mine was shooting the cphp at 1020 out of the box. 2 x .2mm jets, reg at ? With the .22 350mm.

 

[shortfuse]

Where are all the Dirty 30 guys I’m getting 844 FPS at 71 fpe from my 350 mm with reg set at 160 bar with 2X .3 jets have a 450 barrel coming this week hoping to get to 90 fpe

 

[Cranky1]

Mine was shooting the cphp at 1020 out of the box. 2 x .2mm jets, reg at ? With the .22 350mm.

I’m thinking the newer guns have be restricted with the removable internal parts. I will check the jets when I decide to order a bottle. Plus for me it’s shooting the 18jsb and 20grn avs too good to mess with. 

8 8at 40 yards, the two fliers were my fault. 20grain avs. 

 

[Glem.Chally]

Mine was shooting the cphp at 1020 out of the box. 2 x .2mm jets, reg at ? With the .22 350mm.

I’m thinking the newer guns have be restricted with the removable internal parts. I will check the jets when I decide to order a bottle. Plus for me it’s shooting the 18jsb and 20grn avs too good to mess with. 

8 8at 40 yards, the two fliers were my fault. 20grain avs.

Yeah I guess we got the old stock up here Does yours have the externally adjustable reg?

 

[Cranky1]

Mine was shooting the cphp at 1020 out of the box. 2 x .2mm jets, reg at ? With the .22 350mm.

I’m thinking the newer guns have be restricted with the removable internal parts. I will check the jets when I decide to order a bottle. Plus for me it’s shooting the 18jsb and 20grn avs too good to mess with. 

8 8at 40 yards, the two fliers were my fault. 20grain avs.

Yeah I guess we got the old stock up here

Does yours have the externally adjustable reg?

Yes it has the repr reg. It is shooting 15.89 at 916fps with a small adjustment from the previous velocities I posted. Haven’t had the chance to chrony it, but the 18jsb shoot almost as good as the avs slugs.