Hey guys, any of you know what ring height is needed to clear the magazine on a Daystate Wolverine? I tried doing a search but it came up empty.
Daystate Wolverine ring height
- Thread starter AncientSword
- Start date
I have fx no limit rings on mine. Their nice to be able to keep cross hair near center for most room to click
Upvote 0
I’d give AoA a call, they would know for sure. It’s likely going to be high or extra high due to the magazine clearance.
Upvote 0
This is from the AoA invoice when I bought my Wolverine 2 Hi-Lite .303.
1 AZT-E552550 Aztec Emerald 5.5-25x50 Scope
1 SM-HT071 Sportsmatch 2-Pc 30mm Extra High Mounts
Darren spec'd it out, and they mounted everything there.
I hope you enjoy yours as much as I do mine. My youngest can literally crawl up on the bench, and using a bipod, wrap her face around the scope (it's set to my eye relief not hers) and at 50 yards actually drive sheet-rock nails into a board.
1 AZT-E552550 Aztec Emerald 5.5-25x50 Scope
1 SM-HT071 Sportsmatch 2-Pc 30mm Extra High Mounts
Darren spec'd it out, and they mounted everything there.
I hope you enjoy yours as much as I do mine. My youngest can literally crawl up on the bench, and using a bipod, wrap her face around the scope (it's set to my eye relief not hers) and at 50 yards actually drive sheet-rock nails into a board.
Upvote 0
Yeah, I was checking the used section on AOA a couple of weeks ago and a Wolverine Super Grade .22 was on there. I waited a day but when no one grabbed it, I couldn’t resist. It just came in and I was thinking about ordering some new rings for it. I don’t have much in dovetail rings, but I do have adapters. Was considering getting silver rings to match with the receiver.
Upvote 0
Here's what is on mine. There's plenty of clearance with these high rings. Actually wish they were a little lower since the mag slides in from the side.
Upvote 0
I ended up using some medium rings that barely fit, but I want to order some silver rings. Thinking BKL but open to suggestions.
Upvote 0
On both of my Daystate Wolverines (a .22 R and a .25 HP R) I used MIZUGIWA 1 Inch High Profile Rings to mount my Hawke 4-12x40 scopes. First, I tried the medium height MIZUGIWA rings and found that they were not tall enough - the mag would go in, but rubbed the bottom of the scope and would not advance to the next pellet. Don't know about other brands of rings.
Here they are (they are prefect):
https://www.amazon.com/gp/product/B01A5ICTRS/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Bobby
Here they are (they are prefect):
https://www.amazon.com/gp/product/B01A5ICTRS/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
Bobby
Upvote 0
Yes, I also think medium rings will allow the scope tube to clear the mag (just), and also allow a 50mm objective to clear the shroud on the barrel.
I just ordered a pair, for my 30mm tube scope to fit on Wolverine, so I should no for sure on Sunday night or Monday.
I just ordered a pair, for my 30mm tube scope to fit on Wolverine, so I should no for sure on Sunday night or Monday.
Upvote 0
I bought Accushot UTG medium.
They're OK, good for the price (about $13 or $14,shipped). The mediums allow close to 1cm space to from magazine to bottom of tube, so plenty of room.
Although aluminum, they do feel a little heavy considering we don't need anything so substantial for PCPs that don't kick.
They're OK, good for the price (about $13 or $14,shipped). The mediums allow close to 1cm space to from magazine to bottom of tube, so plenty of room.
Although aluminum, they do feel a little heavy considering we don't need anything so substantial for PCPs that don't kick.
Upvote 0