Bullet Central Tungsten hammer install

[BulletCentral]

A quick video for you guys. We have been having questions about how hard it is to install the BC Custom Tungsten hammers.

Pull up a chair and have a quick watch. Installing the hammer isn't as hard as you think.

 

[AKairgunner907]

I was literally just looking for a better video on the hammer install. This was much needed. Excellent timing.

 

[BulletCentral]

Glad you can use it.

The one thing I didn't mention on the video. Is when you are lifting up the bolt assembly....BE VERY CAREFUL! You don't have to lift it up much to get the hammer out.

As always, just give us a call if you need any help.

 

[MEC17670]

A quick video for you guys. We have been having questions about how hard it is to install the BC Custom Tungsten hammers.

Pull up a chair and have a quick watch. Installing the hammer isn't as hard as you think.

Good video, do you have one on installing the tungsten hammer in a Crown mk2?
Thanks , Mike

 

[BulletCentral]

On the crown not as of yet. I can put that in the works and see what we can't get done.

 

[douger]

i see nobody useing loc tit on the c3

 

[Impact701]

I installed my B/C tungsten hammer weight today.

I left 1st and 2nd regulators the exact same as before the install as well as the valve adjuster, micro and macro adjusters.

Velocity went from 965 to 1020 fps with 2nd reg at 142 bar. Shooting NSA 36.2gr HP.

I had to turn down the micro adjuster from just over 4 to just under 2.5 for my target speed of 985 for the 36.2gr HP.

These are all some initial settings as I plan to shoot at least 38.5 HP or the 40gr Heavy HP.

The gun is alot quieter and docile to shoot without all that spring tension smacking the valve.

 

[Nsboost]

I installed my B/C tungsten hammer weight today.

I left 1st and 2nd regulators the exact same as before the install as well as the valve adjuster, micro and macro adjusters.

Velocity went from 965 to 1020 fps with 2nd reg at 142 bar. Shooting NSA 36.2gr HP.

I had to turn down the micro adjuster from just over 4 to just under 2.5 for my target speed of 985 for the 36.2gr HP.

These are all some initial settings as I plan to shoot at least 38.5 HP or the 40gr Heavy HP.

The gun is alot quieter and docile to shoot without all that spring tension smacking the valve.

View attachment 301576

View attachment 301577

View attachment 301578

View attachment 301580

View attachment 301581

View attachment 301582

Which one of the two weights did you get? The heavy one or the lighter one?

 

[Impact701]

Which one of the two weights did you get? The heavy one or the lighter one?

The standard weight. It is 14 grams

 

[BulletCentral]

You will be able to push the regulators higher, or if you are wanting to tame the rifle a little more. You are able to run the same regulator pressures but use a much lower spring tension. This will help to really smooth down the cycle of the action, as well as not put so much stress on the internals.

 

[M0ist0ne]

@BulletCentral did you ever release the spring for the heavy hammer?

 

[Healthservices]

I found, at least with the MK2 and the standard tungsten weight to hit too hard below 150 to get consistent speeds. Around 160 is where I started finding more control.

Allen

 

[BulletCentral]

@BulletCentral did you ever release the spring for the heavy hammer?

I have quite a few of them on order and waiting for them to show up.

As soon as they are here in the shop I will post here to let everyone know.

 

[BulletCentral]

I just got the "Blue Springs" in stock. We are working on getting them on the site and ready to ship out to you guys!

 

[alinyus]

I just got the "Blue Springs" in stock. We are working on getting them on the site and ready to ship out to you guys!

What is the recommended reg pressure and power wheel setting for 33 grains slug on .22 700mm?